• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1017-1025
• /
• 2008

The air data system(ADS) was developed for unmanned aerial vehicle(UAV) in this paper. Generally, the ADS helps flight control computer(FCC) to control the UAV above the stall speed and to hold the given altitude. The accurate measurement of airspeed and altitude of UAV is important because it indicates a flight performance and assures a safe flight. The ADS consists of MEMS pressure sensors, a lowpass filter, a micro controller unit and a pitot-tube. The ADS errors were reduced by pressure and temperature compensation of MEMS sensors. Finally, the altitude and airspeed data of the ADS was compared with GPS data in the flight test.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.3
• /
• pp.233-240
• /
• 2012

An experimental study to improve the impingement characteristics of the assist gas in laser cutting was carried out. For various assist-gas pressures, and locations and installation angles of the nozzle, the characteristics of the impingement of the jet from a supersonic rectangular nozzle were compared to those previously observed for typical circular nozzles. Schlieren flow visualizations and Pitot pressure measurements downstream of the kerf surface were utilized for this purpose. The present rectangular supersonic nozzle decreased the strength of the Mach disc occurring at the corner of the kerf surface, and thus, could weaken the separation of the assist gas on the kerf surface and increase the Pitot pressures downstream compared to conventional circular nozzles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.4
• /
• pp.69-75
• /
• 2003

The ideal thrust function is used to determine the local thrust of supersonic combustor. Method of thrust determination from measured pressures are applied to the Mach 2.5 model supersonic combustor. In this application, measured pressures from the experiments in the University of Michigan are used to determine the local thrust of supersonic combustor. Marginal results of local thrust are obtained and discussed. Combustion and wedge affect thrust distributions in the upstream region significantly. The thrust determination from pressure measurements can be a simple, feasible and applicable method, especially when thrust stand is not available.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.253-254
• /
• 2002

The determination of thrust is very important in hypersonic air-breathing propulsion design and evaluation. Because of the short flow-residence time in the combustor, the evaluation of engine performance is strongly influenced upon the engine thrust. Conventional methods to determine the thrust is using thrust stand or force measurement system. However, these methods cannot be applied to the case where thrust stands are impractical, such as free jet testing of engines, and model combustor. With this reason, the thrust determination method from measured pilot pressure is considered and evaluated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.359-363
• /
• 2011

In this paper, the characteristic of pressures had been analyzed with a series of shapes that are pressure probes used in supersonic wind tunnel. When a performance of supersonic wind tunnel is evaluated, the Mach number is calculated by using the ratio of static pressure in test section wall to total pressure in settling chamber. Also the flow condition can be visualized by schlieren system. However a number of limitations exist to measure pressure of test section due to high speed and boundary layer effect. Therefore a specific pressure probe is needed for evaluating flow condition in test section at a various of positions. In the paper, experiments were conducted in terms of some pitot probes and the results were compared and analyzed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.11
• /
• pp.747-754
• /
• 2022

An experimental study was carried out to control a shock-induced boundary layer separation by utilizing the supersonic sweeping jet from the fluidic oscillator. High-speed schlieren, surface flow visualization, wall pressure measurement and precise Pitot tube measurement were applied to observe the influences of the location and the supply pressure of the fluidic oscillator on the characteristics of the oblique-shock-induced boundary layer separation. The characteristics of the separation control by the present supersonic fluidic oscillator was quantitatively analyzed by comparing with a conventional control method utilizing an air-jet vortex generator.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.10-20
• /
• 2022

The performance analysis test of the scramjet engine intake was conducted under the Mach 5 condition of the scramjet engine test facility, a free-jet ground test facility of the Korea Aerospace Research Institute. A pitot/static pressure rake installed at the rear of the isolator was designed and manufactured to measure the total pressure recovery rate and mass capture ratio, which are typical performance factors of the scramjet engine intake. The effect of the rake mounted at the rear of the isolator on the intake, the performance analysis measured by the rake, and the change in wall static pressure distribution according to the angle of attack were performed. Finally, the point at which the intake unstart occurred was confirmed by using the rear back pressure adjusting device, which simulates pressure rise in the combustor, and the results are summarized in this paper.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.24-31
• /
• 2002

The effects of vortex generators, in the form of small delta-shaped tabs or thin tapes at an axi-symmetric supersonic nozzle exit, on the characteristics of supersonic jet flowfields are investigated by Schlieren images and Pitot-tube measurements. Small tabs as small as 1 % of the nozzle exit area can introduce streamwise vortices and produce a significant effect on the jet flowfield downstream of the nozzle. The effect is stronger for the cases of under-expanded jet than over- and perfect-expanded cases, introducing a larger flow entrainment. The effects of the angle of tabs with respect to the flow direction are also investigated, and for over-expanded jet cases, it is found that the tabs bended toward upstream can weaken the interaction strength and remove the Mach disc in the jet flowfield. Introduction of small proturbances inside the nozzle surface by attachment of thin tapes is also found to change the pressure distribution in the circumferential direction of the flowfield. Its effect is also found to be dependent on the jet expansion ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.306-309
• /
• 2006

Passive control of the shock wave/turbulent boundary-layer interaction control utilizing slotted plates over a cavity has been carried out. Effect of various slot configurations on the characteristics of the interactions are tested. Pitot/wall surface pressure distributions and flow visualizations including Schlierens and interference fringe patterns over a thin oil-film have been obtained at the downstream of the shock interactions. It was found that the interaction control by a certain slot-configuration could lead a reduction of the total pressure loss through the shock wave, however, the boundary layer thickness became thicker as compared with the case of no control.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.3
• /
• pp.230-236
• /
• 2012

The purpose of this research is to determine the calibration constants of the wind speed measurement systems required to calculate the wind tunnel velocity in the test section. In the present work, the aerodynamic calibration tests of the test section were conducted in the Agency for Defense Development's Low-Speed Wind Tunnel. The test speed ranged from 10 to 100 m/s with a reference pitot-static pressure probe. The validity of the calibration results was evaluated by comparing them with the previous calibration constants. The calibration results show that fair to good agreement is obtained with resonable accuracy.