• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.2
• /
• pp.129-151
• /
• 2022

In the current work, a series of three-dimensional finite element analyses have been carried out to understand the behaviour of piles when the adjacent tunnelling passes underneath grouped piles with a reinforced pile cap. In the current study, the numerical analysis studied the computed results regarding the ground reinforcement condition between the tunnel and pile foundation. In addition, several key issues, such as the pile settlements, the axial pile forces, the shear stresses and the relative displacements have been thoroughly analysed, and the IoT platform based preliminary design guidelines were also presented. The pile head settlements of the nearest pile from the tunnel without the ground reinforcement increased by about 70% compared to the farthest pile from the tunnel with the maximum level of reinforcement. The quality management factor data of the piles were provided as API (Application Programming Interface) of various forms by the collection and refinement. Hence it has been shown that it would be important to provide the appropriate API by defining the each of data flow process when the data were created. The behaviour of the grouped piles with the pile cap, depending on the amount of ground reinforcement, has been extensively analysed, and the IoT platform regarding the quality management of piles has been suggested.

• Journal of the Korea Concrete Institute
• /
• v.18 no.6 s.96
• /
• pp.811-817
• /
• 2006

The primary purpose of this study is to estimate the guaranteed strength and construction quality of the combined high flowing concrete which is used in the slurry wall of underground LNG storage tank. The required compressive strength of this type of concrete become generally known as a non economical value because it is applied the high addition factor for variation coefficients and low reduction factor under water concrete. Therefore, after estimation of the construction quality and guaranteed strength in actual site work, this study is to propose a suitable equation to calculate the required compressive strength in order to improve its difference. Application results in actual site work are shown as followings. The optimum nix design proportion is selected that has water-cement ratio 51%, sand-aggregate ratio 48.8%, and replacement ratio 42.6% of lime stone powder by cement weight. Test results of slump flow as construction quality give average 616~634mm. 500mm flowing time and air content are satisfied with specifications in the rage of 6.3 seconds and 4.0% respectively. Results of strength test by standard curing mold show that average compressive strength is 49.9MPa, standard deviation and variation coefficients are low as 1.66MPa and 3.36%. Also test results by cored cylinder show that average compressive strength is 66.4MPa, standard deviation and variation coefficients are low as 3.64MPa and 5.48%. The guaranteed strength ratio between standard curing mold and cored cylinder show 1.23 and 1.32 in the flanks. It is shown that applied addition factor for variation coefficients and reduction factor under water concrete to calculate the required compressive strength is proved very conservative. Therefore, based on these results, it is proposed new equation having variation coefficients 7%, addition factor 1.13 and reduction factor 0.98 under water connote.

• Journal of Intelligence and Information Systems
• /
• v.8 no.1
• /
• pp.141-157
• /
• 2002

extensible Markup Language (XML) is a new markup language for data exchange on the Internet. In this paper, we propose a language extensible Rule Markup Language (XRML) which is an extension of XML. The implicit rules embedded in the Web pages should be identifiable, interchangeable with structured rule format, and finally accessible by various applications. It is possible to realize by using XRML. In this light, Web based Knowledge Management Systems (KMS) can be integrated with rule-based expert systems. To meet this end, we propose the six design criteria: Expressional Completeness, Relevance Linkability, Polymorphous Consistency, Applicative Universality, Knowledge Integrability and Interoperability. Furthermore, we propose three components such as RIML (Rule Identification Markup Language), RSML (Rule Structure Markup Language) and RTML (Rule Triggering Markup Language), and the Document Type Definition DTD). We have designed the XRML version 0.5 as illustrated above, and developed its prototype named Form/XRML which is an automated form processing for disbursement of the research fund in the Korea Advanced Institute of Science and Technology (KAISI). Since XRML allows both human and software agent to use the rules, there is huge application potential. We expect that XRML can contribute to the progress of Semantic Web platforms making knowledge management and e-commerce more intelligent. Since there are many emerging research groups and vendors who investigate this issue, it will not take long to see XRML commercial products. Matured XRML applications may change the way of designing information and knowledge systems in the near future.

• KIPS Transactions on Software and Data Engineering
• /
• v.1 no.3
• /
• pp.137-148
• /
• 2012

Cloud service users request dedicated virtual computing resource from the cloud service provider to process jobs in independent environment from other users. To optimize this process with automated method, in this paper we proposed a framework for workflow scheduling in the cloud environment, in which the core component is the middleware called broker mediating the interaction between users and cloud service providers. To process jobs in on-demand and virtualized resources from cloud service providers, many papers propose scheduling algorithms that allocate jobs to virtual machines which are dedicated to one machine one job. With this method, the isolation of being processed jobs is guaranteed, but we can't use each resource to its fullest computing capacity with high efficiency in resource utilization. This paper therefore proposed a cost-efficient job scheduling algorithm which maximizes the utilization of managed resources with increasing the degree of multiprogramming to reduce the number of needed virtual machines; consequently we can save the cost for processing requests. We also consider the performance degradation in proposed scheme with thrashing and context switching. By evaluating the experimental results, we have shown that the proposed scheme has better cost-performance feature compared to an existing scheme.

• The Journal of Information Technology
• /
• v.4 no.3
• /
• pp.87-100
• /
• 2001

IETF has proposed integrated services model(Int-Serv) and differentiated service(Diff-Serv) to supply IP QoS in Internet[1][2]. Int-Serv model uses state information of each IP flow, so satisfies QoS according to traffic characteristics, but increases the amount of flow state information with increasing flow number. Diff-Serv uses PHP(Per Hop Behaviour) and there are well-defined classes to provide differentiated traffics with different services according to delay and loss sensitivity. Diff-Serv model can provide diverse services in Internet because of having no the state and signal information of each flow. As MPLS uses the packet forwarding technology based on label, it implements the forwarding engine of high performance easily. The MPLS can set up the path having different and variable bandwidth and assign each path to particular CoS (Class of Service). Therefore it is possible to support the Diff-Serv model of well- defined classes that can provide the differentiated traffic with different services according to delay and loss sensitivity in IP QoS models of IETF. In this paper we propose a scheme that can accommodate Diff-Serv model to provide QoS. The system performance has been estimated by scheduling plan according to traffic classes.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.254-262
• /
• 2003

In this study, the results of applying cold weather concreting mixed with Accelerator for Freeze Protection(AFP) to full scale structures are presented. Since the determination of W/C and amount of AFP significantly have an effect on strength gain and protection of frost damage in early, a full investigation is needed to determine these values at stage of nux design. The flowability of fresh cold weather concreting with AFP was similar to the same W/C. Lower loss of workability and initial slump flow of concrete using superplasticizer of polycarboxylic ester than that of melamine sulphonate showed that polycarboxylic ester was more effective on elapsed time. Temperature histories of specimens located in insulation boxes at the site was similar to that of structures. Thus, it is cleared that simple adiabatic curing method is effective for evaluating in-place concrete strength than specimens cured by sealing method. The investigation results of development of compressive strength of cold weather concreting included AFP with curing methods by logistic curves indicated that AFP can be effective to gain strength at lower temperature than normal curing temperature. In field testing, vinyl sheets were placed over the concrete sections and AFP enabled concrete to gain $5N/{mm}^2$ to protect frost damage in early ages and specified compressive strength of concrete at 28 days under average temperature of $-2^{\circ}C$ (lowest temperature was $-12^{\circ}C$) during site application.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.7-14
• /
• 2010

In this paper, we introduce a hierarchical internet application traffic classification system based on SVM as an alternative overcoming the uppermost limit of the conventional methodology which is using the port number or payload information. After selecting an optimal attribute subset of the bidirectional traffic flow data collected from the campus, the proposed system classifies the internet application traffic hierarchically. The system is composed of three layers: the first layer quickly determines P2P traffic and non-P2P traffic using a SVM, the second layer classifies P2P traffics into file-sharing, messenger, and TV, based on three SVDDs. The third layer makes specific classification of the entire 16 application traffics. By classifying the internet application traffic finely or coarsely, the proposed system can guarantee an efficient system resource management, a stable network environment, a seamless bandwidth, and an appropriate QoS. Also, even a new application traffic is added, it is possible to have a system incremental updating and scalability by training only a new SVDD without retraining the whole system. We validate the performance of our approach with computer experiments.

• The Journal of Society for e-Business Studies
• /
• v.18 no.2
• /
• pp.223-240
• /
• 2013

RFID(Radio Frequency Identification) is use of an RFID tag applied to object for the purpose of identification and tracking using radio waves. Recently, it is being actively researched and introduced in logistics and manufacturing. RFID portals in supply chains are meant to identify all the tags within a given interrogation zone. Hence the hardware and software mechanisms for RFID tag identification mostly focus on successful read of multiple tags simultaneously. Such mechanisms, however, are inefficient for determining moving direction of tags, sequence of consecutive tags, and validity of the tag reads from the viewpoint of workflow. These types of problems usually cause many difficulties in RFID portal implementation in manufacturing environment, there by having RFID-system developers waste a considerable amount of time. In this research, we designated an RFID portal system with SDO(Sequence, Direction, and Object-flow)-perception capability by using fundamental data supplied by ordinary RFID readers. Using our work, RFID system developers can save a great amount of time building RFID data-capturing applications in manufacturing environment.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.12
• /
• pp.34-43
• /
• 2007

Recently, in addition to the sharp increase of mobile nodes, various kinds of wireless technologies are available for mobile nodes. If IPv6 technology is applied to the network, multi-homing terminals which have several public IP addresses on one interface will be common. Accordingly, there are many research activities on mobility management for multi-interface, multi-homming nodes. In this paper we propose an extended fast handover mechanism for multi-interface MIPv6 environments that uses multi-interface FBU (MFBU) message instead of the existing FBU message. The MFBU message has the "tunnel destination" mobility option that points a specific tunnel destination other than NAR, and "T" flag that indicates the existence of tunnel destination option. The proposed mechanism can improve the TCP performance by mitigating packet reordering during FMIPv6 handover that can cause unnecessary congestion control due to 3 duplicate ACKs. In this paper, we implemented a multi-Interface MIPv6 simulator by extending a single-interface MIPv6 simulator in NS-2, and showed that the performance of TCP traffic is improved by using the proposed multi-interface fast MIPv6.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.3
• /
• pp.301-315
• /
• 2010

Recently, competition between companies has intensified and so has the necessity of creating a new business value inventions has increased. A numbers of Business organizations are beginning to realize the importance of business process management. Processes however can often not go the way they were initially designed or non-efficient performance process model could be designed. This can be due to a lack of cooperation and understanding between business analysts and system developers. To solve this problem, business process mining which can be used as the basis of the business process re-engineering has been recognized to an important concept. Current process mining research has only focused their attention on extracting workflow-based process model from competed process logs. Thus there have a limitations in expressing various forms of business processes. The disadvantage in this method is process discovering time and log scanning time in itself take a considerable amount of time. This is due to the re-scanning of the process logs with each new update. In this paper, we will presents a modified FP-Tree algorithm for FP-Tree based business processes, which are used for association analysis in data mining. Our modified algorithm supports the discovery of the appropriate level of process model according to the user's need without re-scanning the entire process logs during updated.