• Journal of the Korean GEO-environmental Society
• /
• v.19 no.2
• /
• pp.5-12
• /
• 2018

Underground cavities could induce road subsidence, which have been frequently observed in urban areas. Therefore, adequate backfilling materials and the restoring methods of the cavities are required to prevent the road subsidence. The objective of this paper is to evaluate the suitability of backfilling methods using foaming lightweight grouting materials considering the flow values, unit weights, and air contents at slurry and expanded states, and unconfined compressive strengths. The grouting materials consist of water, cement, and foaming agent whose proportions of water, cement, and foaming agent are 25: 25: 1.0 and 25: 25: 1.2. The flow values of the two materials are greater than 200 mm, and their unconfined compressive strengths at 28 days age are smaller than 1.3 MPa. From the results, the two proportions of materials are expected to be effectively used as a backfilling material. However, the material components should be carefully mixed because poor mix of these materials could induce non-homogeneous distribution of air bubbles. The unexpectedly non-homogeneous distribution of air bubbles may induce significant cracks or additional cavities.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.6
• /
• pp.693-702
• /
• 2023

This research explores the potential application of Liquid Red Mud(LRM), a byproduct of industrial processes, in the construction sector. We neutralized LRM(pH 10-12) using nitric acid, aiming to understand its viability in construction applications. The study involved substituting LRM(pH 7-8) in mortar formulations, varying by cement type. We assessed the properties of these mixtures by measuring flow, setting time, and compressive strength. Additionally, X-ray Diffraction(XRD) and Scanning Electron Microscopy(SEM) analyses were conducted to examine the chemical properties. Results indicated a reduction in flow value for LRM and LN(neutralized LRM) compared to the control (Plain ) across different cement types. The setting times(initial and final) for LRM and LN were notably shorter than Plain. In compressive strength tests, LRM replaced with slag cement showed enhanced initial strength, though long-term strength gains were marginal across different cement types. SEM analysis revealed distinct voids in Plain and LN, with LRM exhibiting a fibrous microstructure. XRD patterns in SN(slag neutralized) resembled those in OR(original red mud) and ON(original neutralized), with a notable peak at a 2θ value of 22°. The study concludes that unneutralized LRM, when substituted for slag cement in mortar, yields superior initial strength compared to its neutralized counterpart.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.97-106
• /
• 2009

self-loading, various problems related to construction can be solved as well as the save of construction cost. Thus, this study has an aim of applying foam concrete to structural purpose by adding bottom ash as a reinforcing material like fine aggregate, in contrast to conventional non-structural usage such as soundproofing or insulating materials. In addition, it was evaluated in terms of unit volume weight, flow value, air void, water absorption and dosage of foam agent wether replacement of cement by granulated blast furnace slag or fly-ash has an effect on the material characteristics of foam concrete. As results of experiments, it can be found that the increase of fine aggregate ratio, that is to say, the increase of bottom ash results in the increase of unit volume weight, while decreasing air void and flow value. But, appropriate addition of bottom ash to foam concrete makes it easy to control a homogeneous and uniform quality in foam concrete due to less sensitive to bubbles. As the replacement ratio of mineral admixtures such as granulated blast furnace slag and fly-ash increases, as unit volume weight tends to decrease. In the meanwhile, serious effects were shown on fluidity of foam concrete when more than limit of replacement ratio was applied.

• The KIPS Transactions:PartB
• /
• v.17B no.4
• /
• pp.275-286
• /
• 2010

Reversible watermarking which can preserve the original quality of the digital contents and protect the copyright has been studied actively. Especially, in medical, military, and art fields, the need for reversible watermarking is increasing. This paper proposes a high-capacity reversible watermarking through predicted error expansion and error estimation compensation. Watermark is embedded by expanding the difference histogram between the original value and the predicted value. Differently from previous methods calculating the difference between adjacent pixels, the presented method calculates the difference between the original value and the predicted value, and that increases the number of the histogram value, where the watermark is embedded. As a result, the high capacity is achieved. The inserted watermark is extracted by restoring the histogram between the original value and the predicted value. To prove the performance, the presented algorithm is compared with other previous methods on various test images. The result supports that the presented algorithm has a perfect reversibility, a high image quality, and a high capacity.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.9B
• /
• pp.823-833
• /
• 2003

To satisfy the requirements of the real-time Internet services, queue management and scheduling schemes should be enhanced to accommodate the delay and jitter characteristic of them. Although the existing queue management schemes can address the congestion problems of TCP flows, they have some problems in supporting real-time services. That is, they show performance degradation when burst traffics are continuously going into the system after the queue is occupied at a predefined threshold level. In addition, under the congestion state, they show large jitter, which is not a desirable phenomenon for real-time transmissions. To resolve these problems, we propose a SDRED (State Dependent Random Early Detection) and dynamic scheduling scheme that can improve delay and jitter performances by adjusting RED parameters such as ma $x_{th}$ and $w_{q}$ according to the queue status. The SDRED is designed to adapt to the current traffic situation by adjusting the max,$_{th}$ and $w_{q}$ to four different levels. From the simulation results, we show that the SDRED decreases packet delays in a queue and has more stable jitter characteristics than the existing RED, BLUE, ARED and DSRED schemes.mes.mes.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.336-345
• /
• 2001

The construction of underwater structures has been increased, but underwater concrete hassome problems of quality deterioration and contamination around in-situ of civil and architecture; therefore, new materials and methods for them are demanded. In this paper in-situ application of underwater antiwashout concrete which is manufactured for trio purpose of not only decreasing suspended solids and the heat of hydration but also increasing long term strength was studied. In the case of mock-up test(Ⅰ), when underwater antiwashout concrete, whose slump flow was 58 cm, was placed in the mock-up test at a speed of 24 ㎥/hr, it took about a minute to flow to the side wall, and the surface was maintained at horizontal level. In this case, compressive strength of the core specimens in each section was higher than the standard design compressive strength of 240 kgf/㎠. In the case of mock-up test(II), pH value and suspended solids of high strength underwater antiwashout concrete were 10.0∼11.0 and 51 mg/ℓ at 30 minutes later, initial and final setting time were about 30, 37 hr, and the slump flow of that was 53$\pm$2 cm. In the placement at a speed of 27 ㎥/hr, there was no large difference in flowing velocity, with or without reinforcement and flowing slope was maintained at horizontal level. In this case, compressive strength and elastic modulus of the core specimens somewhat decreased as flowing distance was far : however, those of central area showed the highest value.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.84-84
• /
• 2023

소하천의 유속계측을 위해 가장 많이 사용되고 있는 표면영상유속계는 표면유속을 계측하는데, 계측된 표면유속을 이용하여 유량을 산정하기 위해서는 수심 평균유속으로 변환할 필요가 있다. 이때 평균-표면유속 환산계수가 주로 사용되는데, 적정 환산계수를 산정하기 위해서는 수심별로 유속을 직접 계측하고 계측된 유속분포를 이용하여 평균-표면유속 환산계수를 산정하는 방법을 사용한다. 그러나 소하천은 홍수시 유속이 매우 빨라 물속에 직접 들어가는 것이 어렵고 장비를 이용하여 간접적인 방법으로 계측을 한다고 하더라도 소류사와 유송잡물 등으로 계측기가 파손되어 직접 계측에는 한계가 있다. 또한 직선구간 확보나 식생 등으로 부자를 이용한 계측도 어려워 계측 결과를 이용하여 환산계수를 산정하는 방법은 한계가 있다. 이런 이유로 대부분은 USGS가 제시한 0.85 ~ 0.95 범위 값 중에서 현장 여건을 고려하여 최적값을 결정·사용하고 있다. 본 연구에서는 홍수시 수심-유속분포를 직접 계측하기 어려운 소하천에서 표면영상유속계를 이용하여 계측한 수심별 표면유속분포를 이용하여 평균-표면유속 환산계수를 산정하는 방법을 개발하였다. 개발한 방법을 정량적으로 평가하기 위하여 건설기술연구원의 안동 하천실험시설에서 표면영상유속계로 수심상승에 따른 횡방향 유속분포를 계측하고 수위가 완전히 상승한 이후의 안정된 흐름 조건에서 플로우트래커를 이용하여 수심별 횡방향 유속분포를 계측하여 두 계측결과를 1:1로 비교하였다. 비교 결과 표면영상유속계로 계측한 수심별 표면유속분포와 플로우트래커로 계측한 수심-유속분포 결과는 유사한 분포를 보이는 것으로 나타나 표면영상유속계로 계측한 수심별 표면유속분포를 이용하여 평균-표면유속 환산계수를 산정하는 것이 가능하다는 결론을 도출하였다. 본 연구에서는 개발한 평균-표면유속 환산계수 산정방법의 적용성을 검토하기 위하여 표면영상유속계가 설치된 5개 시범소하천에서 7년(2016~2022)간 계측한 수심별 표면유속 자료를 수집하고 이 결과를 이용하여 평균-표면유속 환산계수를 산정하였다. 산정결과 대부분 USGS가 제시한 범위내의 값을 보이는 것으로 나타나 향후 본 연구의 개발 방법을 평균-표면유속 환산계수 산정에 활용할 수 있을 것으로 판단된다. 본 연구에서는 개발한 환산계수 산정방법은 향후 보다 많은 수리실험과 현장실험 등으로 정밀검증을 수행한다면 홍수시 수심-유속분포를 직접 계측하기 어려운 소하천에서 간편하면서도 적용성이 큰 신기술 확보가 가능할 것으로 기대된다.

• Korean Journal of Remote Sensing
• /
• v.36 no.5_1
• /
• pp.763-774
• /
• 2020

Wind data forecasted from the numerical weather prediction (NWP) model is generally used as the first-guess of the target tracking process to obtain the atmospheric motion vectors(AMVs) because it increases tracking accuracy and reduce computational time. However, there is a contradiction that the NWP model used as the first-guess is used again as the reference in the AMVs verification process. To overcome this problem, model-independent first guesses are required. In this study, we propose the AMVs derivation from Lucas and Kanade optical flow method and then using it as the first guess. To retrieve AMVs, Himawari-8/AHI geostationary satellite level-1B data were used at 00, 06, 12, and 18 UTC from August 19 to September 5, 2015. To evaluate the impact of applying the optical flow method on the AMV derivation, cross-validation has been conducted in three ways as follows. (1) Without the first-guess, (2) NWP (KMA/UM) forecasted wind as the first-guess, and (3) Optical flow method based wind as the first-guess. As the results of verification using ECMWF ERA-Interim reanalysis data, the highest precision (RMSVD: 5.296-5.804 ms^-1) was obtained using optical flow based winds as the first-guess. In addition, the computation speed for AMVs derivation was the slowest without the first-guess test, but the other two had similar performance. Thus, applying the optical flow method in the target tracking process of AMVs algorithm, this study showed that the optical flow method is very effective as a first guess for model-independent AMVs derivation.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.33 no.3
• /
• pp.427-435
• /
• 2023

Cardinality estimation is used in wide range of applications and a fundamental problem processing a large range of data. While the internet moves into the era of big data, the function addressing cardinality estimation use only on-chip cache memory. To use memory efficiently, there have been various methods proposed. However, because of the noises between estimator, which is data structure per flow, loss of accuracy occurs in these algorithms. In this paper, we focus on minimizing noises. We propose multiple data structure that each estimator has the number of estimated value as many as the number of structures and choose the minimum value, which is one with minimum noises, We discover that the proposed algorithm achieves better performance than the best existing work using the same tight memory, such as 1 bit per flow, through experiment.

• KIISE Transactions on Computing Practices
• /
• v.21 no.12
• /
• pp.780-785
• /
• 2015

Recently HTTP (Hypertext Transfer Protocol) adaptive streaming services have been the subject of much attention. The video quality control scheme of conventional HTTP adaptive streaming services estimates bandwidth using segment throughput and smooths out the sample of segment throughput. However, the conventional scheme has the problem of QoE (Quality of experience) degradation occurring with buffer underflow and frequent quality change due to the fixed number of samples. In order to solve this problem, we propose a video quality control scheme based on segment throughput and buffer occupancy. The proposed scheme determines the number of samples according to the variation of segment throughput. The proposed scheme also controls video quality based on the threshold of bitrate to keep stable buffer occupancy. The simulation results show that proposed scheme improves QoE by preventing buffer underflow and decreasing quality change when compared with the conventional scheme.