• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4075-4079
• /
• 2010

In this paper, structural analysis was conducted by ANSYS code for three dimensional finite element method to the pipe butt welding machine. Based on this numerical structural analysis, stress, strain and total deformation were obtained and the design change of the pipe butt welding machine was made along with improved productivity and shorten design period.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2006.06a
• /
• pp.47-51
• /
• 2006

레이저를 이용한 폴리머의 융착기술은, 자동차산업에서의 다양한 적용분야에 힘입어 새로운 접합기술로 각광을 받고 있다. 현재까지는, 대부분 작고 간단한 형상의 제품을 융착하는 분야에 많이 적용되어 왔으며, 튼 사이즈의 제품을 대량으로 생산하는 공정에서는 레이저융착이 가지는 다양한 장점에도 불구하고, 프로세스의 안정성, 사출후의 제품변형에 따른 갭의 관리, 작업속도등에 대한 이유로 본격적인 적용을 기피하고 있는 실정이다. 이러한 배경에 의하여 개발된 하이브리드방식(레이저빔+할로겐램프)의 폴리머융착 시스템은, 다이오드레이저에서 출력되는 $800{\sim}980nm$의 레이저파장과 할로겐 램프에서 방사되는 적외선영역의 파장을 동시에 사용함으로써 프로세스의 안장성과 융착효율을 향상시켰다.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.62-62
• /
• 2010

PVC(Polyvinyl Chloride)와 HDPE(High-density Polyethlene) 하수도관은 수많은 고분자 재료 중에도 높은 기계적 강도를 가지며, 광범위하게 사용되고 있다. 하지만, PVC와 HDPE 하수관을 연결하기 위해 소모 접착제나 고무링 이용한 소켓 방법 이음 방법은 낮은 수밀성과 기계적 강도로 오 폐수의 누수가 발생되고, 이것이 흙에 스며들어 지하수, 하천 및 토양을 오염시키고 있다. 따라서, 대안으로 최근에는 열판을 이용한 맞대기 융착 용접을 PE 하수도 관에 제한적으로 적용하여 시공하고 있다. 그러나, PVC 하수관은 열을 가할 시 열에 의한 민감한 거동으로 인해 맞대기 융착 용접법이 적용되지 못하고 있는 실정이다. 따라서 본 연구에서는 하수도 관 중, 국내에서 가장 많이 사용되고 있는 내 충격 PVC 하수도관과 HDPE 이중 벽관의 DSC(Diffential Scanning Calorimeter), TGA(Thermogravimetric analyzer), TMA(Thermomechanical Analysis), DMA(Dynamic Mechanical Analysis) 분석으로 온도에 따른 열적 거동을 분석하여, 적절한 융착 온도 조건을 제시하였다. 또한 접합강도 향상을 위한 이음부 설계를 제안하여, 융착 용접 특성을 평가하였다.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.64-68
• /
• 2013

Non destructive testing(NDT) methods of electrofusion(EF) joints of thermoplastics pipes are required for fusion joint safety and for the long term reliability of a pipe system. Electrofusion joints, which are joined at the proper fusion process and procedures, may encounter defects due to the difference of ovality between pipes and coupling, improper fusion process or porosity result from electrofusion joining. These defects can cause the failure of pipeline and by extension, they can be caused the limit to expand the use of plastics pipes. This paper studies inspection results using ultrasonic imaging method for damaged polyethylene electrofusion joints. Gas was leaking from 250mm diameter polyethylene electrofusion joints at February 2004 which was electrofused at December 1994 and operation pressure was 2.45kPa. First, surface inspection was conducted and then in order to find the types of defects examination using ultrasonic imaging method was performed. Lack of fusion and inappropriate inserting for polyethylene pipes into electrofusion coupling were found and causes of the gas leak were judged that misalignment and insert defect. Cutting inspection was performed and each inspection results were compared to. Results of ultrasonic imaging method and cutting inspection were the same.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.1
• /
• pp.96-102
• /
• 2012

The current establishment of car engineering plastic piping polyethylene (PE) tube used as bonding state or part of the health or safety of fusion is very important. A part of these fusion methods to determine the soundness of the short-term trials and long-term tests can be largely classified. Typical tests included short-term strength, tensile strength, impact strength, compressive strength, resiliency and compression. Polyethylene (PE) pipes installed in the domestic terms of overall penetration rate of 45% has been used. However, polyethylene (PE) pipes have reliability problems, and these occurs mostly in part by defective welding. Therefore, the test is necessary for safety. Non-destructive methods (ultrasonic testing) are difficult to be used. Therefore, Polyethylene (PE) pipe are used. Fusion of thses materilas is necessary in these field however, its technical, and basic research has not been studied well. In this research, short-term strength of welding parts, its tensile strength, hardness, fatigue, and microstructure have been analyzed to find the optimum process conditions to improve mechanical properties.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.5
• /
• pp.564-569
• /
• 2011

The current establishment of city gas piping polyethylene (PE) tube used as bonding state or part of the health or safety of fusion is very important. A part of these fusion methods to determine the soundness of the short-term trials and long-term tests can be largely classified. Typical tests include short-term strength, tensile strength, impact strength, compressive strength, resiliency and compression. Polyethylene (PE) pipes installed in the domestic terms of overall penetration rate of 45% has been used. However, polyethylene (PE) pipes have reliability problems, and these occurs mostly in part by defective welding. Therefore, the test is necessary for safety. Non-destructive methods (ultrasonic testing) are difficult to be used. Therefore, Polypropylene copolymer (PP-C), polypropylene homopolymer (PP-H), and polyethylene (PE) pipe are used. Fusion of these materials is necessary in these field however, its technical, and basic research has not been studied well. In this research, short-term strength of welding parts, its tensile strength, hardness, fatigue, and microstructure have been analyzed to find the optimum process conditions to improve mechanical properties.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.63-71
• /
• 2018

A flower support was developed for real flower decoration automation production system using an ultrasonic wave sealer to automatically produce a system. Because a flower support for real flower decoration that was produced manually could not meet the needs of the consumers, this study developed an automated manufacturing system to increase productivity. A flower support for real flower decoration was constructed using a cap consisting of plastic and plate made from non-woven fabric. The guide was designed to transport the cap to the ultrasonic wave sealer and optimal guide was developed from the test according to the material and shape. To produce the entire system, the guides and accessories were weighed and appropriate motors and pulleys were calculated. Control of the automation production system was based on a PCB board, which increased the reliability and security, and a remote controller with manual and automatic modes was prepared. After development, tests of the transfer precision and repetition accuracy revealed an X-axis of 2.7mm, a Y-axis of 1 mm, and a repetition of 0 mm. The productivity was also checked. The automated machine worked 8 hours/day to make 35 supports and 70 Therefore, the automatic system produces 200% more output than manual work

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.154-163
• /
• 2013

Adhesive bonding and plastic welding have been widely used to join two plastic materials together. The goal of this paper is to determine a proper joining technology of a pair of flat panel (FP) photobioreactor (PBR) case. The material of the FP PBR case is polycarbonate (PC) plate. Two types of adhesion, including acryl adhesive and two-part epoxy adhesive, as well as two types of plastic welding technology, including ultrasonic welding and thermal welding, are employed for joining of PC plates. In order to influence of the adhesion and welding conditions on the joining characteristics of the PC plates in operational conditions of the FP PBR case, the morphology in the vicinity of the joined region as well as the water and pressure resistance characteristic are investigated. In addition, the variation of the bonding strength of the joined region and deformation behaviors in the vicinity of the joined region according to the adhesion and welding conditions is examined via the lap-shear test. From the results of basic experiments, proper joining technologies are chosen. Using the chosen joining technologies, the FP PBR case are fabricated to perform full-scale durability experiment. The results of the full-scale durability experiment have been shown that the chosen joining technologies can be applicable to fabricate the FP PBR case.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.11
• /
• pp.595-599
• /
• 2013

The pipes used in buildings are generally categorized into metallic or plastic materials. Metal pipes, such as copper and stainless steel pipes, are mainly used for water and hot water supply, and for the heating system. However, plastic pipes made of polyethylene and cross-linked polyethylene are used for floor heating, water drainage, and air vent systems. Usually, plastic pipes have thermal demerits, such as high linear expansion coefficients and bending phenomenon by hot water, although the pipes have several merits of light weight, low price, low thermal conductivity, and the comparatively high workability of metal pipes. Therefore, if those kind of demerits are overcome, plastic pipes can be easily accepted for hot water systems. This research is aimed to evaluate the applicability for vertical heating pipes of a plastic pipe system consisting of electric fusion fitting of a conductive carbon compound and propylene random glass fiber pipe, through measurement of the expansion rate and leakage in summer and winter seasons, in the apartment construction field.