• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.35-45
• /
• 1990

Casting are widely used nodays as complicated and diversified forming materials due to its superior castability. However the welding of cast iron has not been accompaniced satisfactory resulting in an microstructure change happened in the heat affected zone (HAZ), especially the graphite are formed and shaped consecutively in the area and it has great impact on the crack occuring and growth together with martensite forming in this area. It case of gray cast iron welding, it is required for pre-heat treatment or specific welding consumables to restrain forming the martensite in the HAZ. In this study, by applying the plasma surface overlaid welding. Fe-Mn-Al steel powder has been used for improvement of anti-crackability in the HAZ and much attention has been paid to establish the overlaid welding method for gray cast iron so that optimum welding conditions may prevent the cracking. With our experiments, we have found that to prevent defects which may occur in the HAZ, the overlaid welding technique for gray cast iron has been developed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.159-160
• /
• 2007

저온 플라즈마 침탄 처리 후 연속적인 공정으로 저온 플라즈마 질화를 실시하여 내식성과 표면경도를 향상시키는 처리에서 질화처리 시 Ar 가스가 표면특성에 미치는 영향을 조사 하였다. 모든 시편의 경도가 미처리재 보다 약4배 증가하였으며, Ar가스의 양이 증가할수록 N의 침투깊이가 깊어졌다. 전체 경화증의 두께는 거의 일정하였고, 경화층은 모재보다 내식성이 증가되어 단면조직사진에서 밝게 나타났다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.157-158
• /
• 2007

AISI316L강의 내식성과 표면경도를 동시에 향상시키기 위한방법으로 저온 플라즈마 침탄과 저온 플라즈마 질화를 동일한 로 내에서 연속적으로 실시하였다. 여러 가지 공정인자 중 저온 플라즈마 질화 시 $N_2$가스가 표면에 미치는 영향을 조사 하였다. 모든 시편의 표면에 N에 의해 확장된 오스테나이트 (${\gamma}_N$)가 형성되었으며, 형성된 ${\gamma}_N$로 인하여 표면경도가 약 $3{\sim}4$배 증가하였다. $N_2$가스가 증가할수록 ${\gamma}_N$층의 두께가 증가 하였다.

• Journal of the Korean Vacuum Society
• /
• v.15 no.1
• /
• pp.57-63
• /
• 2006

We have examined the electrical and optical characteristics of the plasma display panel(PDP) produced by vacuum in-line sealing technology. We found that the luminous efficiency was decreased as the base vacuum level was increased. For the base vacuum level of $1\times10^{-3}$ Torr, the firing voltage was 235V at the discharge gas pressure of 400 Torr and the luminous efficiency was 0.8 lm/W at 180V sustaining pulse. However, for the base vacuum level of $1\times10^{-6}$ Torr, the firing voltage was reduced to 215V and the luminous efficiency was improved to 2.5lm/w. Finally, we demonstrated successfully the operation of tip-less PDP fabricated using vacuum in-line sealing method.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.57-65
• /
• 1997

A study was undertaken to determine the influence of welding variables such as shielding and plasma gases, torch standoff, travel speed and heat input, etc. on the quality of plasma arc welds in Zircaloy-4 sheet, 2mm thick. Effect of shielding gases and their flow rates on the mechanical properties of Zircaloy-4 welds by plasma arc welding were determined in terms of tensile, bardness and bend tests. The microstructure and fracture surface of Zircaloy-4 welds were investigated by optical and scanning electron microscopies. In addition, the causes of porosity and undercut in plasma arc welds of Zircaloy-4 were also investigated. Zircaloy-4 weld bead width and depth by helium shielding gas showed a wider and deeper than those by argon. It was found that Zircaloy-4 welds with shielding gas of helium did dxhibit a little smoother and uniform weld beads than those with shielding gas of argon. It was also found that the optimum gas flow rates for Zircaloy-4 welding were 0.45l/min for plasma gas with Ar and 4.5 - 6 l/min for shielding gas with He. In addition, there was no big difference in the microstructure and fracture surface of the weld metals made by either Ar shielding gas or He shielding gas.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.5
• /
• pp.394-399
• /
• 2001

In this Paper, the development of the power supply for dry scrubber is discussed. 1500w, 100kHz power supply Is designed and tested. The main power stage is used for the FB PWM inverter with an LC filter in the secondary circuit. The operation characteristics of power supply are verified by simulation and experimental results.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.65-70
• /
• 2015

This research examines the removal efficiency of benzene, toluene, xylene (BTX) and total volatile organic compounds (TVOCs) by flowing VOCs, which are generated at a petrochemical complex in the Ulsan area, in a sliding arc plasma (SAP) reactor. The SAP reactor process is composed of 5 steps and the analysis was conducted using a BTX detector and TVOC measuring instrument. The removal efficiency of BTX was better at high concentration than at low concentration and the emitted TVOC concentration increased in later steps of the reactor. In addition, the removal efficiency improved, as the flow velocity increased. The maximum permissible concentration of TVOCs in the first step was about 481 ppm and showed over 94.83% efficiency when it was operated in the 2nd step at concentrations beyond 481 ppm. Therefore, there are many factors for improving the removal efficiency of SAP reactors at low concentration and measures should be prepared according to the application method for the various types of industrial reactors.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.7
• /
• pp.50-57
• /
• 1989

Tapered etching of polysilicon films has been achieved by implanting phosphorus ions into the polysilicon film and using plasma etch in either $CF_4-O_2\;or\;SF_6$. A two-step plasma etching method is also proposed to control the taper angle of the etched edge without changing the implantion conditions. The taper angle is determined by the ratio of the etch rate of the undamaged region to that of the damaged top region of the polysilicon layer. The ratio is found to be dependent on the implantion dose, the implantion energy and the anisotropy of etching. The minimum angle in our experiments is about $10^{\circ}$. When the two-step etching method is employed, the taper angles can be controlled from the minimum angle up to about $55^{\circ}$.