• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.475-479
• /
• 2003

Traditional ultrasonic evaluation to detect micro/small surface cracks is the pulse-echo technique using the normal immersion transducer with high frequency, or the angle beam transducer with surface wave. It is difficult to make the automatic ultrasonic system that is to detect micro and small surface crack and position on the large structure like steel and ceramic rolls, because of the huge data of inspection and the ambiguous position data of transducer. The aim of this study using the high precision scanning acoustic microscope with 10MHz large aperture transducer was to display the real time A, B, C-scan for the automatic ultrasonic system in order to detect the existence and position of surface crack. The ultrasonic method with large aperture transducer was improved the scanning time and speed over 10times faster than traditional methods.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.2
• /
• pp.40-47
• /
• 1993

Composites composed of a precipitation harden 2124 alloy matrix reinforced by SiC whiskers, which are fabricated by powder metallugy, are suscepttible to fatigue damage due to the pile-up of moving dislocation and the microcrack initiation along SiC-Al interfaces, especially at the external surfaces of a body. The initial process, such as pile-up of dislocation or microcrack, that corresponds to the stage I during fatigue failure process are too small to be detected and characterized by conventional ultrasonic technique. This paper describes the applicability of an acoustic microscope with Line-Focus-Beam(LFB) lens of 225MHz to evaluate fatigue damage of SiC whiskers reinforced Al alloy. The specimens which were 6.6mm thick, 13mm wide, and 105mm long in the gage section were fatigued in tension-tension under load control. The velocity of leaky surface and leaky pseudosurface acoustic waves are obtained by FFT analysis technique from V(z) curve which is a record of output of piezoelectric transducer. These results are discussed with the change of number of fatigue cycles. The result obtained by acoustic microscope is compared with that by ultrasonic technique generated at 5MHz with conventional surface wave transducers.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.1
• /
• pp.82-90
• /
• 2000

An experimental study has been carried out at circulating water channel to investigate the non-breaking and breaking waves generated by a submerged circular cylinder steadily moving under the free surface. Free surface profiles and pressure distributions on cylinder surface were measured at various submerged depths of cylinder. They were complemented by the measurements of velocities, head losses and turbulence intensities in the wakes of body and "breaker". Part 1 of this three-part paper describes the experimental arrangement and the patterns of wave profile and pressure distribution at various depths of submergence. These databank contributions are of special interest in traditional ship hydrodynamics. In Part 2, special focuses are made to elucidate the viscous and turbulent aspects of flow field. Finally Part 3 will deal with the visualization of instantaneous vortical flow to study the mutual interaction between vorticies shedded from the free-surface and the cylinder using a Particle Image Velocimetry.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.1
• /
• pp.9-16
• /
• 2014

In recent years, the structural shock response to UNDEX (UNDerwater EXplosion) has been studied as much, or more, through numerical simulations than through testing for several reasons. Very high costs and sensitive environmental concerns have kept destructive underwater explosion testing to a minimum. Increase of simulation capabilities and sophisticated simulation tools has made numerical simulations more efficient analysis methods as well as more reliable testing aids. In this study, the main issue is the fluid-structure interaction. Here, appropriate relations between the acoustic pressure on the fluid surface and displacements on the structure surface are formed internally. The analysis was carried out using ABAQUS/Explicit and the results have been visualized in ABAQUS CAE. The shock loading history, acoustic pressure, stress of stand-off point, the velocity and strain energy time histories were presented.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.267-275
• /
• 2012

Austenite stainless steel 304 has properties of high resistance to corrosion and temperature changes. Therefore, this material is widely used in various of industries. However, when the material is subjected to heating and cooling cycles the forming accuracy, for example, the right angle associated with a sharp bend such as corner is lost. This phenomenon is caused by the reversion of the deformation-induced martensite into austenite when the temperature in increased. This result in misfit of a structure or an assembly, and an increase in residual stress. Hence, it is important to understand this process. In this study, to evaluate the mechanical behavior of the deformation-induced martensite and reversed austenite, a scanning acoustic spectroscope including the capability of obtaining both phase and amplitude of the ultrasonic wave (i.e., the complex V(z) curve method) was used. Then, the velocities of the SAW propagating within the specimens made in different conditions were measured. The experimental differences of the SAW velocities obtained in this experiment were ranging from 2,750 m/s to 2,850 m/s, and the theoretical difference was 3.6% under the assumption that the SAW velocity was 2,800 m/s. The error became smaller as the martensite content was increased. Therefore, the SAW velocity may be a probe to estimate the marternsite content.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.211-217
• /
• 2014

This study analyzes the nonlinear interaction between two different vortex shedding frequencies from a cylinder with two diameters. In particular, two different vortex shedding frequencies are generated by preparing a cylinder having two diameters artificially. Flow velocity fluctuations behind the cylinder are measured three-dimensionally. Additionally, we fabricated a hole and placed a pressure transducer for measuring the pressure on the cylinder surface. The pressure signal from the pressure transducer is used as basic signal. A TSC(Trans Spectrum Coherence) is used for checking the strength of the nonlinear interaction between two different vortex shedding frequencies. As a result, the following are clarified: i) frequency distribution behind the cylinder, ii) three-dimensional flow state behind the cylinder through calculation of ensemble average, and iii) close relationship between the vertical vortex and change of low frequency by nonlinear interaction between two different vortex shedding frequencies from the cylinder with two diameters.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.114-131
• /
• 1992

In the present work, a two-dimensional boundary-value problem for a large amplitude motion is treated as an initial-value problem by satisfying the exact body-boundary and nonlinear free-surface boundary conditions. The present nonlinear numerical scheme is similar to that described by Vinje and Brevig(1981) who utilized the Cauchy's theorem and assumed the periodicity in the horizontal coordinate. In the present thesis, however, the periodicity in the horizontal coordinate is not assumed. Thus the present method can treat more realistic problems, which allow radiating waves to infinities. In the present method of solution, the original infinite fluid domain, is divided into two subdomains ; ie the inner and outer subdomains which are a local nonlinear subdomain and the truncated infinite linear subdomain, respectively. By imposing an appropriate matching condition, the computation is carried out only in the inner domain which includes the body. Here we adopt the nonlinear scheme of Vinje & Brevig only in the inner domain and respresent the solution in the truncated infinite subdomains by distributing the time-dependent Green function on the matching boundaries. The matching condition is that the velocity potential and stream function are required to be continuous across the matching boundary. In the computations we used, if necessary, a regriding algorithm on the free surface which could give converged stable solutions successfully even for the breaking waves. In harmonic oscillation problem, each harmonic component and time-mean force are obtained by the Fourier transform of the computed forces in the time domain. The numerical calculations are made for the following problems. $\cdot$ Forced harmonic large-amplitude oscillation(${\omega}{\neq}0,\;U=0$) $\cdot$ Translation with a uniform speed(${\omega}=0,\;U{\neq}0$) The computed results are compared with available experimental data and other analytical results.

• Tunnel and Underground Space
• /
• v.11 no.4
• /
• pp.362-367
• /
• 2001

The stiff top layer in a soil profile, which can happen in winter, may change the isolation effect of the wave barrier. The research scope of this paper is the investigation of the propagation of surface waves in layered soil with a stiff layer on its top, and the isolation effect of the solid stiff wave barrier. The investigations have been performed numerically by the Boundary-Element Method as a two-dimensional problem. A strip foundation vibrated harmonically in vertical direction was considered as the vibration source. Three soil profiles, a homogeneous half-space, two profiles with different thickness of stiff top layer, with two different types of wave barriers were investigated. The profiles with a stiff top layer show considerable reductions of the amplitude of the vibration in comparison to the homogeneous soil profile. The layered soil profiles with a stiff top layer do not show wave propagation velocities as high as they are expected from the material properties. Furthermore the vibration amplitudes in a frozen soil are much smaller with distance than in a non-frozen soil.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.218-224
• /
• 2013

Generally, SAW device, which uses Time Domain Sampling, requires high speed A/D converter because SAW device using TDS needs high sampling speed as much as its high data speed. However, the high price of A/D converter discourages makers from using it. On the other hand, SAW device, which uses Frequency Domain Sampling, does not required high speed A/D converter because SAW device using FDS does not need high sampling speed. It is very efficient in price comparison to its performance because high processing speed of SAW device using FDS can be implemented using low price Embedded Systems. The purpose of the paper is to solve the issues above by designing and realizing SAW device(FDS) using SAW sensor for TDS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.89-89
• /
• 2000

AlN 박막은 Al과 N원자의 부분적 이온결합 특성을 가진 공유결합을 한 육방정계의 wurtzite 경정구조의 화합물 반도체로서, III-V족 반도체 중 가장 큰 에너지 갭(6.2 eV), 결정 구조적 이방성, 화학 양론적 결합구조, 높은 탄성종과 전달속도(약 10$\times$106 m/s)와 높은 열전도도, 고온 안정성, 가시광성.적외선 영역에서의 좋은 투과성과 높은 굴절률, 상온 대기압에서의 유일하게 안정적인 특성을 가지고 있어, 절연재료, 내열재료, 저주파 영역 센서의 압전 트랜스듀서, 광전소자, 탄성파 소자 및 내환경 소자, MIS소자 등으로 주목받고 있다. 본 연구에서는 BAW 공진기의 활용을 목적으로 반응성 마그네트론 스퍼터링 방법으로 AIN 압전박막을 제작하여, 증착 조건-질소 농도, 고주파 출력, 전체 스퍼터링 압력, 기판 온도-에 대한 박막의 특성을 조사하였다. AlN 박막의 c축 우선 방위 결정성 및 낮은 투과성, 적당한 굴절률의 특성이 BAW 공진기의 활용을 위한 요건이므로, 각각의 증착 조건하에 제작된 박막은 XRD의 $\theta$/2$\theta$ 스캔 회절상에 의한 결정성의 분석과 우선 성장 결정면의 rocking curve 및 XRD로 측정한 FWHM과 표준 편차로 결정성의 배열성과 소자 응용가능성을 조사하였다. 박막의 표면.단면 미세 구조 및 평활도는 SEM으로 관찰하였으며, Al-N 결합 상태는 XPS와 FT-IR로 분석 조사하였다. 제작된 AlN 박막의 결정성 분석 결과, c축 우선 방위 성장을 위한 스퍼터링 압력에 대한 임계 질소 농도와 임계 스퍼터링 압력이 관찰되었다. 전체 스퍼터링 압력이 6~8 mTorr의 범위에서 나타난 최소 임계질소 농도는 10%, 최대 임계 질소 농도는 60%이며, 4 m Torr 이하 10 m Torr 이상의 전체 스퍼터링 압력에서 박막의 우선 방위성장이 제재된다. 이는 AlN 박막이 형성에 관여하는 질소 이온 양의 충분한 형성에 필요로 하는 질소 가스의 유입량에 따른 것으로 판단된다. AlN 박막의 c축 결정면인 (002) 결정면의 성장을 유도하며 다른 방향으로의 성장을 제어하여 소자 활용에 유용한 박막을 제작하기 위한 고주파 출력은 300W 정도가 적당하며, 기판을 가열하지 않았을 때 낮은 투과도를 나타낸다. 본 연구에 의한 BAW 공진기 활용을 위한 AlN 압전박막의 제작을 위한 최적 증착 조건은 기판의 가열 없이 6~8 mTorr의 전체 스퍼터링 압력에 20~25%의 질소종도, 300W의 고주파 출력이다. 최적 조건에서의 AlN 박막은 약 0.19$^{\circ}$의 FWHM과 약 0.08$^{\circ}$의 표준편차를 가지며, 균일하고 조밀한 표면 미세구조와 주상정 구조의 측면구조, 파장에 대한 약 2.0의 굴절률, 낮은 투과도와 화학 양론적 구조를 가지는 우수한 박막이 형성되었다.