• 대한방사선방어학회:학술대회논문집
• /
• 2009.04a
• /
• pp.202-203
• /
• 2009

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.193-193
• /
• 2015

도금공정에 있어서 전처리는 제품품질을 확보하는데 중요한 단계이다. 전처리 공정의 주요인자중 처리액의 온도, 처리시간, 교반력, 오염도를 개선함으로써 제품의 산화막 및 오염물질을 효과적으로 제거할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.121.1-121.1
• /
• 2015

전기애자 표면의 오염도에 따라 절연능력이 상실되어 불시에 원치 않은 고장 및 사고의 원인이 된다. 이러한 오염도는 애자가 사용되는 장소에 따라 다르지만, 특히 터널과 지하구간처럼 밀폐되어 있는 공간에서의 오염정도는 매우 심각하다. 본 연구에서는 기능성 나노코팅을 이용한 애자의 표면 코팅으로 내오염 특성을 향상시켜 오염에 의한 절연능력 저하를 억제하는 방안을 제시하였다. 기능성 나노코팅은 전기애자와 재질이 같은 세라믹 기판위에 코팅하였고, 열처리 분위기에 따른 변화를 실험하였고, 주변 분위기로는 질소, 알곤, 산소, 진공의 네 가지 분위기로 수행하였다. 세라믹 기판 위에 합성된 기능성 나노코팅의 특성분석은 내오염 특성, 접촉각, 부착력, 경도를 수행하였고, 실험에 활용된 기능성 나노코팅이 세라믹 기판 표면 오염방지에 탁월한 효과를 가짐을 확인하였다.

• Proceedings of the Korean Society of Veterinary Service Conference
• /
• 2001.06a
• /
• pp.186.1-186
• /
• 2001

• Proceedings of the KSAR Conference
• /
• 2002.06a
• /
• pp.195.1-195
• /
• 2002

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.3
• /
• pp.512-521
• /
• 2015

In this research, environmental friendly organic acid containing microetching system to improve adhesion strength between photoresist resin and Copper Clad Laminate(CCL) was developed without using strong oxidant $H_2O_2$. Etching rate and surface contamination on CCL were examined with various etching conditions with different etchants, organic acids and additives. to develope an optimum microetching condition. Etching solution with 0.04 M acetic acid showed the highest etching rate $0.4{\mu}m/min$. Etching solution with the higher concentration of APS showed the higher etching rate but surface contamination on CCL is very serious. In addition, stabilizer solution also played an important role to control the surface contamination. As a result of research, the etching solution containing 0.04 M of acetic acid, 0.1 M of APS with 4 g/L of stabilizer solution(ST-1) was best to improve adhesion between CCL and photoresist resin as well as showed the most clean and rough surface with the etching rate of $0.37{\mu}m/min$.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.12 no.1
• /
• pp.3-12
• /
• 2008

Purpose: Contaminated clothes and bedclothes of patients by mouth or with excrement are produced after Radioisotope $^{131}I$ treatment. In this paper, patient's clothes and bedclothes contaminated by radioactivity measured and radioactive waste wish to calculate optimum storage period. Material and Methods: The whole area of patients' clothes and bedclothes measured 70 patients, 12 males and 58 females, who had radioisotope $^{131}I$ therapy between August 2005 and February 2006. Assuming contamination is evenly distributed, the radioscope used to measure up to social toleration level at 7 day intervals. Results: Each optimum storage period of control group of 60 case and non control group of 10 case were average $44{\pm}16$ days and $32{\pm}13$ days. Decontamination effect of surface contamination for radioactive waste was average $83.66{\pm}15.15%$. Conclusion: It is important that classify radioactive waste according to difference of surface contamination. Result of this research, handling radioactive waste in optimum storage period may be useful.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.659-662
• /
• 2009

본 연구는 건축자재로 널리 사용되는 PVC 바닥상재 표면의 오염성 및 정전기로부터 보호하기 위하여 기존에 사용하는 광경화형 우레탄-아크릴 수지에 내오염/대전성을 향상시킨 광경화형 내오염 코팅액 개발에 관한 것이다. PVC 바닥상재용으로 사용되는 내오염성이 없는 우레탄-아크릴 수지에 4가 암모늄을 사용한 수용성 대전방지제와 아크릴용 대전방지제, 폴리우리탄용 대전방지제를 수지의 양 대비 함량(wt%) 5~20%로 변화하여 첨가한 후 1000rpm에서 30분간 고속 배합하여 수지의 내오염/대전성을 향상시킨 내오염 코팅액을 제조하였다. 제조한 내오염 코팅액은 코팅 층의 두께조절이 가능한 코팅(Bar-coating)을 사용하여 PVC 바닥상재에 코팅 한 후 내오염성, 대전성, 부착력, 코팅두께 등의 코팅 층 표면물성을 평가하였다. 연구결과, 수지에 수용성대전방지제 15%를 혼합하여 제조한 코팅액을 Bar-coater No.12로 코팅한 코팅표면이 전기저항($3.24{\times}10^9{\Omega}/cm^2$), 내오염도(매직 Test, 먼지부착 Test) 및 부착력(100%) 모두 가장 좋은 물성을 보였으며, 전반적으로 함량이 많을수록 전기저항과 오염도에서 우수한 것으로 나타났다. 그러나 대전방지제가 과량으로 들어간 경우 migration 현상이 보이는 것을 알 수 있었다.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.21-29
• /
• 2005

The HANARO, a multi-purpose research reactor of 30 MWth open-tank-in-pool type, has been under normal operation since its initial criticality in February, 1995. Recently, ten years after the initial operation of the HANARO, one of the two primary cooling pumps was decontaminated for overhaul maintenance in 2004. Before decontamination exposure doserate and surface contamination level of primary cooling pump measured at 4 points. After final decontamination exposure doserate and surface contamination level of primary cooling pump remeasured by same method done before. It is easy to decontaminate the out side exposed surfaces of the pump, but it is difficult to approach the inside surface due to double volute installed in the casing. Therefore, a new decontamination facility has been developed to solve this problem. A concentrated de-contaminant (DX-300) is rotated in the closed pump casing by the impeller actuated by a temporary motor. Nuclide particles are removed by the emulsification effect of the de-contaminant and the surface contaminants are chemically removed from the pump by the corrosion and dissolution effect. The inside surfaces of the primary cooling pump have been decontaminated by using the facility. As results, the contamination level of the inside surfaces was maintained below the surface contamination limit.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.3 no.3
• /
• pp.159-165
• /
• 2005

The characterization of radiological contamination inside pipes generated during the decommission of a nuclear facility is necessary before pipes can be recycled or disposed. But, existing direct measurements of radioactive contamination level using the survey-meter can not estimate the characteristic of contamination on a local area such as the pipe inside. Moreover, the measurement of surface contamination level using the indirect methods has many problems of an application because of the difficulty of collecting sample and contamination possibility of a worker when collecting sample. In this work, plastic scintillator was simulated by using Monte Carlo simulation method for detection of beta radiation emitted from internal surfaces of small diameter pipe. Simulation results predicted the optimum thickness and geometry of plastic scintillator at which energy absorption for beta radiation was maximized. In addition, the problem of scintillator processing and transferring the detector into the pipe inside was considered when fabricating the plastic detector on the basis of simulation results. The characteristic of detector fabricated was also estimated. As a result, it was confirmed that detector capability was suitable for the measurement of contamination level. Also, the development of a detector for estimating the radiological characteristic of contamination on a local area such as the pipe inside was proven to be feasible.