• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.1008-1012
• /
• 2008

Nanoscale zero-valent iron(nZVI) is famous for its high reactivity originated from its high surface area and it has received considerable attentions as one of the latest innovative technologies for treating contaminated groundwater. Due to its fine powdery form, nZVI has limited filed applications. The efforts to overcome this shortcoming by immobilizing nZVI on a supporting material have been made. This study investigated the differences of resin-supported nZVI's characteristics by changing the preparation methods and evaluated its reactivity. The borohydride reduction of an iron salt was proceeded in ethanol/water solvent containing a dispersant and the synthesis was conducted in the presence of ion-exchange resin. The resulting material was compared to that prepared in a conventional way of using de-ionized water by measuring the phyrical and chemical characteristics. BET surface area and Fe content of nZVI-attached resin was increased from $31.63m^2/g$ and 18.19 mg Fe/g to $38.10m^2/g$ and 22.44 mg Fe/g, respectively, by switching the solution medium from water to ethanol/water with a dispersant. The reactivity of each material was tested using nitrate solution without pH control. The pseudo first-order constant of $0.462h^{-1}$ suggested the reactivity of resin-supported nZVI prepared in ethanol/water was increased 61 % compared to that of the conventional type of supported nZVI. The specific reaction rate constant based on surface area was also increased. The results suggest that this new supported nZVI can be used successfully in on-site remediation for contaminated groundwater.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.1
• /
• pp.60-67
• /
• 2010

Although several studies have reported that Cr, Cu and As can leach from CCA-treated woods, few studies have been conducted on this topic in Korea. Therefore, this study was conducted to monitor Cr, Cu and As leaching from CCA-treated wood products and to develop a rapid identification method for CCA-treated wood products by using indicators such as PAN stain. Soil samples were collected at depths of 0-70 cm and wood samples were collected by thickness of wood layer. The soil and wood samples were then digested and analyzed for Cr, Cu and As concentrations using an atomic absorption spectrometer. The As and Cu concentrations decreased sharply with depth from 34.38 and 33.65 mg $kg^{-1}$ at 0-1 cm to 1.72 and 7.84 mg $kg^{-1}$ at 70 cm, respectively. In general, As was more mobile than Cr and Cu in the soil. For wood samples, the Cr, Cu and As concentrations were higher in the outer layer (0-0.5cm) than the inner layers (0.6-4.5cm). Evaluation of rapid identification methods revealed that 100% acetone with 0.1% PAN indicator was the best combination for detection of CCA-treated wood in the field.

• Korean Journal of Soil Science and Fertilizer
• /
• v.41 no.5
• /
• pp.285-292
• /
• 2008

To investigate the effect of tillage methods on the silage barely growth and the soil environment in paddy field, liquid pig manure(LPM) was applied after harvesting rice at Jisan series soil for 2 years. Five plots, a LPM applied rate as N%; 0, 100, 150, 200(basal dressing) and 100(basal dressing)+50(additional fertilizer) were divided by tillage methods; non-tillage, non-tillage+rice straw and rotary tillage method. Emission amounts of $NH_3$ gas highly decreased in the rotary tillage and the non-tillage+rice straw plot compared to non-tillage plot. The contents of soil organic matter and exchangeable cation were increased in the applied LPM plot. $NH_4-N$ and $NO_3-N$ contents in soil were the highest in the non-tillage+rice straw plot and followed by the rotary tillage and highly decreased along with the growth of plant. Run-off rate of mineral components were higher in order of the rotary tillage plot£æthe non-tillage plot£æthe non-tillage+rice straw plot and then leached to $SO_4$, $NO_3-N$, K plentifully. The yield of silage barley in dry weight was higher in order of the non-tillage+rice straw plot>the rotary tillage plot>the non-tillage plot. To estimate the feed value of silage barley, crude protein, acid detergent fiber(ADF) and neutral detergent fiber(NDF) contents were analyzed. Crude protein and ADF contents were the highest at rotary tillage N150% plot as 9.7 and 29.4%, respectively. NDF contents was the highest at non-tillage+rice straw N150% plot as 56.7%. In conclusion, we recommend not to incinerate rice straw and to apply LPM at non-tillage status in cultivating the silage barley. This may prevent water pollution and increase barley yields.

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.4
• /
• pp.316-323
• /
• 2011

Purpose: The purpose of this study was to investigate the effect of different thread designs on the marginal bone stresses around dental implant. Materials and methods: Standard ITI implant(ITI Dental Implant System; Straumann AG, Waldenburg, Switzerland), 4.1 mm in diameter and 10 mm in length, was selected as control. Test implants of four different thread patterns were created based on control implant, i.e. maintaining all geometrical design of control implant except thread pattern. Four thread designs used in test implants include (1) small V-shape screw (model A), (2) large V-shape screw (model B), (3) buttress screw (model C), and (4) trapezoid screw (model D). Surface area for unit length of implant was 14.4 $mm^2$ (control), 21.7 (small V-shape screw), 20.6 (large V-shape screw), 17.0 (buttress screw) and 28.7 $mm^2$ (trapezoid screw). Finite element models of implant/bone complex were created using an axisymmetric scheme with the use of NISA II/DISPLAY III (Engineering Mechanics Research Corporation, Troy, MI, USA). A load of 100 N applied to the central node on the crown top either in parallel direction or at 30 degree to the implant axis (in order to apply non-axial load to the implant NKTP type 34 element was employed). Quantification and comparison of the peak stress in the marginal bone of each implant model was made using a series of regression analyses based on the stress data calculated at the 5 reference points which were set at 0.2, 0.4, 0.6, 0.8 and 1.0 mm from implant wall on the marginal bone surface. Results: Results showed that although severe stress concentration on the marginal bone cannot be avoided a substantial reduction in the peak stress is achievable using different thread design. The peak marginal bone stresses under vertical loading condition were 7.84, 6.45, 5.96, 6.85, 5.39 MPa for control and model A, B, C and D, respectively. And 29.18, 26.45, 25.12, 27.37, 23.58 MPa when subject to inclined loading. Conclusion: It was concluded that the thread design is an important influential factor to the marginal bone stresses.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.15-20
• /
• 2008

By considering the storage temperatures of agricultural products, three types of PCMs $(K_1$, $K_2$, $K_3$) were developed to be used in temperature ranges of $0{\sim}5^{\circ}C$, $5{\sim}10^{\circ}C$ and $10{\sim}15^{\circ}C$, $K_1$ PCM for $0{\sim}5^{\circ}C$ was developed by mixture of $C_{14}H_{30}$ and soduim polyacrylate, and $K_2$ PCM for $5{\sim}10^{\circ}C$ and $K_3$ PCM for $10{\sim}15^{\circ}C$ were mixture of $C_{14}H_{30}$, $C_{18}H_{38}$ and soduim polyacrylate with different composition ratio. 'The target temperatures of cold chain system were set at $7^{\circ}C$, $13^{\circ}C$, and $17^{\circ}C$ with $K_{1-3}$, $K_{2-3}$ and $K_{3-1}$ PCMs, respectively. The times to reach the target temperatures in the storage chamber were 21 hours, 18 hours, and 61 hours with $K_1$, $K_2$, and $K_3$ PCMs, respectively. The performances of natural convection type and forced convection of the temperature controlled portable container were analyzed Apples were stored in the portable container of $5^{\circ}C$, and temperatures at surface and center were measured. The initial temperature of the apple was $25^{\circ}C$. The temperatures of apple at the surface and the center were $15^{\circ}C$ and $16^{\circ}C$, respectively, after 5 hours with natural convection type. However, the temperatures at the surface and the center were already reached to $7^{\circ}C$ within 1 hour with forced convection type. The forced convection type showed the better performance and the temperatures of portable container were maintained more than 15 hours.

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.49-57
• /
• 2008

This study was conducted to develop an optimal composite recipe for a cookie including yam powder that would be attractive to all age groups. Wheat flour was partially substituted by yam powder to reduce the content of wheat flour. This study has produced the sensory optimal composite recipe by making cookies, respectively with each 5 level of yam powder $(X_1)$, Sugar$(X_2)$, butter$(X_3)$, by C.C.D (Central Composite Design) and conducting sensory evaluation and instrumental analysis by means of RSM (Response Surface Methodology). Sensory items showed very significant values in color, softness, overall quality (p<0.01), flavor (p<0.05) and those of instrumental analysis showed significant values in lightness, redness (p<0.05), spread ratio, hardness (p<0.01). Also sensory optimal ratio of yam cookie was calculated at yam powder 37.35 g, sugar 50.75 g, butter 78.40 g and it was revealed that the factors of influencing yam cookie aptitude were in older of yam powder, butter, sugar.

• Korean Journal of Food Science and Technology
• /
• v.31 no.6
• /
• pp.1529-1535
• /
• 1999

This study was done for the extraction of carotenoid from Phaffia rhodozyma in combination with PEF and other methods. PEF treatment conditions were $30{\sim}80\;kV/cm,\;100{\sim}1000\;Hz\;and\;100{\sim}1000\;{\mu}s$. In order to increase permeability of yeast cell wall, various methods such as freezing-thawing, mechanical treatment, solvents, permeabilizing agents, and yeast cell wall lytic enzyme were used before PEF treatment. The combination of PEF $(50\;kV/cm,\;300\;Hz,\;1000\;{\mu}s)$ and conventional methods such as solvent and freezing-thawing pre-treatment had no effects on the extraction of carotenoid pigments. The extent of extracted carotenoid by the PEF $treatment(50\;kV/cm,\;300\;Hz,\;1000\;{\mu}s)$ combined with yeast cell wall lytic enzyme and mechanical pre-treatment increased 52% and 69.8% more than the sum of that by each treatment, respectively. Permeabilizing agents, especially Tween 20 and capric acid, enhanced the extraction efficiency of carotenoid pigments from P. rhodozyma cells. These results indicated the feasibility for the continuous extracting carotenoid pigments from P. rhodozyma by PEF combined with other permeabilizing methods.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.10
• /
• pp.1475-1485
• /
• 2012

This study was conducted in order to understand nutrition teachers (dietitians)' perceptions of barriers to implementation of HACCP system in school foodservices in Gyeongnam, Korea. Questionnaires were distributed to 350 nutrition teachers (dietitians) from November to December of 2009, and 214 were collected and analyzed. The results of this study were as follows. First, nutrition teachers (dietitians) recognized the following as barriers in implementing the HACCP system: 'the status of facilities and utilities'> 'monitoring'> 'work satisfaction'> 'foodservice employees'> 'cooperation of HACCP team'> 'cooperation of persons concerned besides foodservice employees'> 'understanding the HACCP system'. Second, total working experience was found to be the factor most affecting 'cooperation of HACCP team (p<0.01)', 'cooperation of persons concerned besides foodservice employees (p<0.01)', 'foodservice employees (p<0.05)', and 'work satisfaction (p<0.05)'. Further, 'the status of facilities and utilities' was significantly affected by 'construction/reconstruction of kitchen (p<0.01)', 'division of kitchen area (p<0.01)', 'existence of preliminary preparation room (p<0.01)', and 'existence of dishwashing room (p<0.01)'. Third, dietitians perceived the following concerning hindrance factors of the HACCP system according to CCP stage: 'CCP 1'> 'CCP 3'> 'CCP 2, 'CCP 6'> 'CCP 4'> 'CCP 8'> 'CCP 7'> 'CCP 5'. In conclusion, this study showed that nutrition teachers (dietitians) in the Gyeongnam area recognized 'the status of facilities and utilities' from HACCP areas and 'CCP 1 (menu planning)' from CCP stages as the greatest barriers to implementing the HACCP system in school foodservices. To implement the HACCP system successfully in school foodservices, facilities and utilities should be properly equipped, and menu planning training for nutrition teachers (dietitian) should be conducted.

• Applied Microscopy
• /
• v.29 no.2
• /
• pp.137-147
• /
• 1999

Comparative differences between the fine structure of cultured LL/2 cell in vitro and tumor cells in vivo which were induced in the lung by inoculation of LL/2 cells to C57 BL/6 mouse via tail vein during 21 days are not observed except for cell configuration which was changed spindle shape into oval shape. At first tumor cells appeared at lymphatic nodules and around capillary in the lung. Tumor cells divided actively by mitosis, so they became tumor nodules. The pulmonary aveoli around tumor nodules were observed somewhat flattened in shape but the cells in the aveoli appeared to be in normal condition. Furthermore the normal lung cells were observed in the tumor nodules and some apoptotic tumor cells appeared in the large tumor nodules. A lot of neutropiles were observed in the aveoli and tumor nodules of C57 BL/6 mouse lung after inoculation 22 days and 31days.