• The Journal of Korean Academy of Prosthodontics
• /
• v.61 no.3
• /
• pp.179-188
• /
• 2023

Purpose. The purpose of this study was to evaluate the effect of surface treatments on the shear bond strength of two types of zirconia (3-TZP and 5Y-PSZ) with resin cement. Materials and methods. Two different types of zirconia specimens with a fully sintered size of 14.0×14.0×2.0 mm³ were prepared, polished with 400, 600, and 800 grit silicon carbide paper, and buried in epoxy resin. They were classified into four groups each control, sandblasting, primer, and sandblasting & primer. Cylindrical resin adhered to the surface-treated zirconia with resin cement. It was stored in distilled water (37℃) for 24 hours, and a shear bond strength test was performed. The normality of the experimental group was confirmed with the Kolmogorov-Smirnov & Shapiro-Wilk test. The interaction and statistical difference were analyzed using a two-way ANOVA. A post-hoc analysis was performed using Dunnett T3. Results. As a result of two-way ANOVA, there was no significant difference in shear bonding strength between zirconia types (P > .05), but there was a significant correlation in the sandblasting, primer, and alumina sandblasting & primer group (P < .05). Dunnett T3 post-test showed that, regardless of the type of zirconia, shear bonding strength was sandblasting & primer > Primer > sandblasting > control group (P < .05). Conclusion. There was no difference in shear bond strength between the types of zirconia. The highest shear bond strength was shown when the mechanical and chemical treatments of the zirconia surface was performed simultaneously.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.3
• /
• pp.365-376
• /
• 2006

The purpose of this study was to evaluate the efficacy of blocking the oxygen in the air during the polymerization of sealant. All curing were performed with various light curing units under the application of oxygen gel barrier, stream of nitrogen and carbon dioxide gas for inhibition of oxygen diffusion into sealant surface. The results of present study can be summarized as follows : 1. The amount of eluted TEGDMA form the specimens cured with all the three different light units in the stream of $N_2$ and $CO_2$ gas and application of Oxygen gel barrier($DeOx^{(R)}$) were significantly lower than in the room-air atmosphere (Control) (p<0.05). 2. In the $DeOx^{(R)}$ application, the amount of eluted TEGDMA the specimen cured with PAC light for 10seconds was less than that cured in the stream of $N_2$ and $CO_2$ atmospheric conditions (p<0.05) 3. In the LED using 10 or 20sec irradiation times under the stream of $N_2$ and $CO_2$, the eluted TEGDMA showed to be no statistically significant difference (p>0.05). 4. The microhardness from the specimens cured with all the three different light units under each treated conditions were significantly higher than in the room-air atmosphere (p<0.05). 5. The surface treatment by $DeOx^{(R)}$, $N_2$ and $CO_2$ reduces the thickness of oxygen inhibited layer by sp proximately 49% of the untreated control value.

• Transactions of Materials Processing
• /
• v.14 no.7 s.79
• /
• pp.587-594
• /
• 2005

분무성형공정은 급냉응고 및 결정입자 제어에 따른 고품위 소재 개발의 장점과 함께 고밀도 near-net-shape 제품의 제조가 가능한 합금제조기술이다 분무성형체의 미세조직은 적층표면에 도달하는 액적들의 평균 열용량, 즉 고상분율에 의하여 결정되며, 이는 액적의 비행과정에서의 분사가스-액적간의 열전달과 적층표면에서의 열유입과 열유출 속도에 영향을 받는다. 실제 다양한 공정변수들이 복합적으로 미세조직 형성과정에 영향을 미치지만, 균일한 미세조직을 얻기 위하여서는 적층표면에서의 온도와 고상분율을 항상 일정하게 제어하여야만 한다 즉, 적층표면 온도를 분무 성형공정중에 지속적으로 측정하여 이를 공정 제어 시스템에 feedback하여 원하는 적층표면온도를 유지하도록 공정변수를 제어하는 것이 필수적이다. 분무성형에 제조된 성형체는 합금원소의 편석이 없고 미세한 등방성의 결정립으로 이루어진 특징적인 미세조직을 나타낸다 이와 같은 미세조직으로 인하여 분무성형체는 우수한 성형성과 기계가공성을 나타내며, 또한 분무성형-후속가공된 최종 제품은 잉곳주조에 의하여 제조된 것과 비교하여 크게 향상된 기계적 성질을 가진다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.2
• /
• pp.1-8
• /
• 2009

Present studies of these experiments was conducted to using water, over a range of cross-flow velocities from 42 to 136 m/s, with injection frequencies from 35.7 to 166.2 Hz. In cross-flow field, main parameters of liquid jet for secondary breakup were cross-flow drag rather than pressure pulse frequency. As oscillation of the periodic pressure, liquid jet was moved up and down. Also, a bulk of liquid jet puff was detected at upper field of liquid surface. Because of pressure pulsation frequency, an inclination of SMD for the structured layer was evanescent. Cross-sectional characteristics of SMD at downstream area were non-structured distributions. The tendency of volume flux value for various frequency of pressure pulse was same distribution. And volume flux was decreased when the frequency of pressure pulse increasing.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.53-60
• /
• 2003

CCD(Charge-Coupled Device) wafers, with a layer of micro lenses on top, usually are not passivated with dielectric films. Micro lenses, in general, are made of polymer material, which usually has a large affinity for particles generated in the various chip fabrication processes, most notably the wafer sawing for chip-dicing. The particles deposited on the micro lens layer either seriously attenuate or deflect the incoming light and often lead to CCD failure. In this study we introduce new type of saws which would significantly reduce the particle-related problems found in conventional type of saws. In the new saws, the positions and diverging angles of side and center nozzles have been optimized so as to flush the particles effectively. In addition, an independent nozzle is added for the sole purpose of flushing the generated particles. The test results show that, with the new saws. the ratio of the particle-related CCD chip failures has been dropped drastically from 9.1% to 0.63%.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.78-83
• /
• 2010

On the paved track, the ballast is used as aggregate for the filling layer using the pre-packed concrete technique. The most important condition of aggregate is adhesive strength with mortar. To satisfy this condition, surface of aggregate should be cleaned by water or others. In a paved-track method to be introduced domestically, an environment-friendly dry-washing technology which will replace the water-washing method has been developed. A dry-washing method was designed to blast the crushed weight material with a diameter of 0.3~0.5mm at high pressure to peel the surface of the aggregate. The study was intended to enhance the washing efficiency of dry-blasting technology and to that end, the tests including blasting material, content of fine aggregate depending on time elapsed, content of chloride, LA abrasion rate and compressive strength were conducted to recommend the efficient washing material and the process.

• Journal of Welding and Joining
• /
• v.14 no.2
• /
• pp.19-27
• /
• 1996

재료의 표면개질은 표면층의 조직변화에 대한 개질법과 표면피복에 의한 개질 법으로 나눌 수 있다. 조직변화에 의한 개질법으로는 침탄, 질화, 이온주입 및 금속 확산 등이 있고, 표면피복에 의한 개질법으로는 도장, 도금, 육성용접, 물리증착(PVD) 및 화학증착(CVD) 등이 있는데, 용사법은 표면피복에 의한 개질법에 속한다. 용사기술 은 비교적 최근에 발달된 표면피복 기술로서 그림1과 같이 플라즈마, 가스화염 또는 아크열원을 이용하여 금속 또는 비금속 재료를 용융 혹은 반용융 상태로 모재에 고속 도로 분사하여 충돌 적층시켜 피복하는 공정으로 다른 표면개질기술에 비해서 여러 가지 잇점을 가지고 있다. 이것은 거의 모든 재질의 모재(금속, 세라믹, 유기재료 등) 에 대해 피막의 형성이 가능하고, 용사재료의 종류도 다양하다(금속, 합금, 각종 세라 믹, 플라스틱, 각종 복합재료 등). 또한 노재크기의 제한이 없고, 대형의 재료에 대해 서 한정된 부위의 피복이 가능하며, 모재의 열영향이 적고, 피막의 형성속도가 다른 피막법에 비해 빠른 장점을 가지고 있다. 그 예로 알루미나(Al$_{2}$O$_{3}$)를 피복할 경우 화학증착(CVD)법에 의해서는 피막형성 속도가 약 2 * $10^{-4}$mm/min 인데 비해 용사법에 의해서는 약 7.5 * $10^{-1}$mm/min로 매우크다. 이와같은 많은 장점을 갖고있는 용사법을 이용한 표면개질에 대해 본 기술보고에서 서술하고자 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.4
• /
• pp.53-62
• /
• 2006

Two-dimensional steady flowfields generated by transverse injection jets into a supersonic mainstream are numerically simulated. Fine-scale turbulence effects are represented by a k-${\omega}$ SST two-equation closure model which includes $y^+$ effects on the turbulence model. Solution convergence is evaluated by using Grid Convergence Index(GCI), a measure of uncertainty of the grid convergence. Comparison is made with experimental data and other turbulence models in term of surface static pressure distributions, the length of the upstream separation region, and the penetration height. Results indicate that the k-${\omega}$ SST model correctly predicts the mean surface pressure distribution and the upstream separation length for low static pressure ratios. However, the numerical predictions become less consistent with experimental results as the static pressure ratio increases. All these results are taken within 1% error band of grid convergence.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.341-347
• /
• 2011

This work studies the performance of an injector for a monopropellant thruster, comparing a conventional and new injector types. The conventional injector consists of 8 nozzles on a convex surface allowing the jet to be diverged. The new injector, we suggested, is an impinging type with nozzle holes on a concave surface. The fuel streams through the nozzle holes are collide at a point on an axial direction, which allow to atomize the liquid streams and to spray more uniformly along circular direction. The performance of the injectors is investigated by using computational fluid dynamics, particle image velocimetry and high speed camera visualization.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.1
• /
• pp.9-18
• /
• 2015

Purpose: The purpose of this study is to examine characteristics of implant surface with RBM and anodizing treatments, and to evaluate the responses of osteoblast-like cell (MG-63 cell). Materials and methods: Grade IV titanium disks were fabricated (Diameter 10 mm, thickness 3 mm). Anodizing treatment (ASD) group, RBM and anodizing treatment (RBM/ASD) group, control (machined surface) group were divided. In this study, osteoblast-like cell was used for experiments. The experiments consist of surface characteristics evaluation by FE-SEM images, energy dispersive spectroscopy and stereo-SEM. In order to evaluate cell adhesion evaluation by crystal violet assay and observe cells form by confocal laser microscopy. To assess cell proliferation by XTT assay, cell differentiation by RT-PCR and mineralization by Alizarin red S stain assay. ELISA analyzer was used for Quantitative evaluation. Comparative analysis was run by one-way ANOVA (SPSS version 18.0). Differences were considered statistically significant at P<.05. Results: In ASD group and RBM/ASD group, the surface shape of the crater was observed and components of oxygen and phosphate ions in comparison with the control group were detected. The surface average roughness was obtained $0.08{\pm}0.04{\mu}m$ in the control group, $0.52{\pm}0.14{\mu}m$ in ASD group and $1.45{\pm}0.25{\mu}m$ in RBM/ASD group. In cell response experiments, ASD group and RBM/ASD group were significantly higher values than control group in cell adhesion and mineralization phase, control group was the highest values in the proliferative phase. In RT-PCR experiments, RBM/ASD group was showed higher ALP activity than other groups. RBM/ASD group in comparison with ASD group was significantly higher value for cell adhesion and proliferation phase. Conclusion: In the limitation of this study, we are concluded that the surface treatment with RBM/ASD seems more effective than ASD alone or machined surface on cellular response.