• Economic and Environmental Geology
• /
• v.47 no.3
• /
• pp.247-254
• /
• 2014

The compressibility of fracture in naturally fractured reservoir is larger than the compressibility of matrix in rock, although the compressibility of a typical rock is very small. The effective compressibility including the fracture compressibility should be considered to predict oil recovery correctly. It is hard to quantify changes of fracture aperture and pore volume in reservoir without the effective compressibility. In this study, oil recovery is analyzed by commercial simulator concerning the fracture compressibility based on fracture properties. We found that the effective compressibility affects oil recovery with change of polymer flooding factors such as polymer molar weight, concentration and injection rate. The estimated cumulative oil production is smaller with the effective compressibility than without it. Also, bottomhole pressure decreases rapidly without considering effective fracture compressibility.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.53-61
• /
• 2018

Low-salinity water based polymerflooding (LSPF) is one of promising enhanced oil recovery (EOR) method that has the synergetic effect of combining polymer injection method and low-salinity water injection method. In order to maximize EOR efficiency, it is essential to design low-salinity water appropriately considering the properties of polymer. In this aspect, the main purpose of this study is to investigate the effect of pH and $SO_4{^{2-}}$ ion which one of PDI (Potential Determining Ion) on oil production when applying LSPF to carbonate oil reservoir. First, the stability and adsorption of polymer molecule were analyzed in different pH of injection water and $SO_4{^{2-}}$ concentration in injection water. As a result, regardless of pH and $SO_4{^{2-}}$ concentration, when $SO_4{^{2-}}$ ion was contained in injection water, the stability of polymer solution was obtained. However, from the result of polymer retention analysis, in neutral state of injection water, since $SO_4{^{2-}}$ interfered the adsorption of polymer, the adsorption thickness of polymer was thinner as $SO_4{^{2-}}$ concentration was higher. On the other hand, when injection water was acidic as pH 4, the amount of polymer adsorption increased with the injection of polymer solution, so the mobility of polymer solution was greatly lowered. From the results of wettability alteration due to low-salinity water effect, in the case of neutral injection water injected, as $SO_4{^{2-}}$ concentration was increased, more oil which attached on rock surface was detached, altering wettability from oil-wet to water-wet. On the other hand, in acidic condition, due to complex effect of rock dissolution and polymer adsorption, wettability of the entire core system was less altered relatively to neutral condition. Therefore, it was evaluated that better EOR efficiency was obtained when injecting low-salinity water based polymer solution containing high concentration of $SO_4{^{2-}}$ with neutral condition, enhancing the oil production up to 12.3% compared to low-salinity water injection method.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.3
• /
• pp.29-39
• /
• 2022

The engineering characteristics of synthetic polymer-silica sol, which has the effect of reducing leakage, was evaluate and compared with typical grouting material, the water glass-based SGR injection material in this study. The result of the laboratory tests on strength and durability about the synthetic polymer-silica sol showed more than twice as high as LW-based injection materials in uniaxial compressive strength, significantly lower values in shrinkage rate and permeability. The result of pH was less than 8.5 (the drinking water quality standard). As a result of the leaching test, the Na₂O elution amount of the synthetic polymer-silica sol was measured to be 3 to 4 times smaller than that of the water glass grout. These results be assumed that the synthetic polymer-silica sol has better durability and permeability than those of the typical water glass-based grout.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.5
• /
• pp.387-401
• /
• 2023

The Earth Pressure Balanced (EPB) Shield Tunnel Boring Machine (TBM) is widely employed for constructing urban underground spaces due to its minimal vibration and low noise levels. The injection of additives offers several advantages, including maintaining shield chamber pressure, reducing shear strength, minimizing cutter wear, and decreasing the permeability of the excavated soil. This technique is known as soil conditioning and involves the application of additives such as foam, polymer, and bentonite slurry. In this study, weathered granite soil commonly encountered at domestic tunnel sites was used as a soil specimen. Foam and polymer were applied as additives to assess the rheological properties of conditioned soils. The workability was evaluated through slump tests, while the rheological properties were assessed through laboratory pressurized vane shear tests conducted under the same conditions. Specially, the polymer was applied under specific conditions with low workability with high slump values, with the aim of evaluating the impact of polymer application. The test results revealed that with an increase in the Foam Injection Ratio (FIR), the slump value also increased, while the torque, peak strength, yield stress, apparent viscosity, and thixotropic area decreased. Conversely, an increase in the Polymer Injection Ratio (PIR) led to results opposite to those of FIR. Additionally, a correlation between the slump value and yield stress was proposed. When comparing conditions with only foam applied to those with both foam and polymer applied, even with similar slump values, the yield stress was found to be lower in the latter conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.184-184
• /
• 2016

대기압 플라즈마를 이용한 폴리머 합성은 기존의 합성방법에 비해 간단하고 쉽게 폴리머를 합성할 수 있다는 장점이 있다. 대부분의 폴리머는 합성온도가 $150^{\circ}C$ 이하이기 때문에 각 폴리머에 적합한 온도를 제어하는 것이 핵심이라 할 수 있다. 본 연구에서는 폴리머 합성온도를 제어하기 위하여 플라즈마 방전전극에 모노머를 직접 주입하지 않고 간접적인 방법을 선택했다. 그리고 모노머는 액체 공급 장치를 이용해 플라즈마의 가스량과 파워를 제어하면서 폴리머를 합성의 조건을 찾았다. AC 플라즈마를 이용해 methyl methacrylate($C_5H_8O_2$) 모노머를 폴리머로 합성했으며, 그 결과는 FTIR, XRD 등으로 분석하고 특성을 평가했다. FTIR의 결과, C-O, C-H, C=O 등의 전형적인 poly methyl methacrylate(PMMA)의 피크를 확인할 수 있었다. 그리고 XRD의 관찰결과 C1s 및 O1s의 각 binding energy가 각각 283, 285, 288 eV 및 533 eV 주변에서 확인되었다. 그리고 합성시간에 따라 폴리머의 두께가 비례해서 증가하는 것을 관찰할 수 있었다. 실험결과, AC 플라즈마를 이용한 폴리머합성은 가능한 것으로 확인되었으며 소형화 및 휴대가 가능하기 때문에 식품, 바이오, 의약품, 의료용품 등의 현장포장 등 여러 가지 용도로 활용이 가능할 것으로 판단된다.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.837-843
• /
• 1997

In oxidized polyethylene wax preparation, the effects of main parameters such as the property of used wax, oxidation time, oxidation temperature, air feed rates on the change of acid-numbers were investigated. The change in polymer property was also investigated. The results showed under given reaction conditions, the acid numbers with oxidation temperature increased upto $160^{\circ}C$, but at higher temperature, it decreased. The base resin which was lower molecular weight had higher acid number. The result showed molecular weight as a experimental parameter was more effective than density in oxidation experiment. In milder condition, free radical initiator was used for catalyst to get higher acid-numbers, which was successful in comparison to the non-catalyst system. Also the catalyst with longer half-life was efficient, in order of DCPO, HOPO and BPO.

• Polymer(Korea)
• /
• v.32 no.6
• /
• pp.566-572
• /
• 2008

Polyethylene has been prepared via metallocene catalysts [(TMDS)$Cp_2$]$ZrCl_2$, 1, and [$(n-Bu)_2Cp_2$]$ZrCl_2$, 2, in the presence of hydrogen as a chain transfer reagent. Increase of hydrogen flow to the polymerization reactor resulted in the drop of catalytic activity, reduction of molecular weight of polyethylene, getting narrow of molecular weight distribution of polyethylene, and melting point of the polyethylene wax. It should be noticed that it was possible to control molecular weight down to 1500 and melting temperature to 60 $^\circ$C of polyethylene wax using the catalyst 1 that has been developed by authors as well as the catalyst 2 from Exxon.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.4
• /
• pp.545-560
• /
• 2019

During EPB TBM tunnelling, an appropriate application of additives such as foam and polymer is an essential factor to secure the stability of TBM as well as tunnelling performance. From the '90s, there have been many studies on the optimal injection of additives worldwidely contrary to the domestic situation. Therefore, in this paper, the foam, which is widely adopted for soil conditioning, was selected as an additive in order to investigate the effect of foam injection on TBM performance through a series of laboratory excavation tests. The excavation experiments were carried out on artificial sandy soil specimens with consideration of the variance of FIR (Foam Injection Ratio), FER (Foam Expansion Ratio) and $C_f$ (Surfactant Concentration), which indicate the amount and quality of the foam. During the tests, torque values were measured, and the workability of conditioned soil was evaluated by comparing the slump values of muck after each experiment. In addition, a weight loss of the replaceable aluminum cutter bits installed on the blade was measured to estimate the degree of abrasion. Finally, the foam injection ratio for the optimal TBM excavation for the typical soil specimen was determined by comparing the measured torque, slump value and abrasion. Note that the foam injection conditions satisfying the appropriate level of machine load, mechanical wear and workability are essential in the EPB TBM operational design.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.7
• /
• pp.690-698
• /
• 2010

Contamination of groundwater resources by organic chemicals has become an issue of increasing environmental concern. Surfactant-enhanced aquifer remediation (SEAR) is widely recognized as one of the most promising techniques to remediate organic contaminations in-situ. Solutions of surfactant or surfactant with polymer are used to dramatically expedite the process, which in turn, may reduce the treatment time of a site compared to use of water alone. In the design of surfactant-based technologies for remediation of organic contaminated aquifers, it is very important to have a considerable analysis using extensive numerical simulations prior to full-scale implementation. This study investigated the formation and flow of microemulsions during SEAR of organic-contaminated aquifer using the finite difference model UTCHEM, a three-dimensional, multicomponent, multiphase, compositional model. The remediation process variables considered in this study were the sequence of injection fluids, the injection and extraction rate, the concentrations of polymer in surfactant slug and chase water, and the duration of surfactant injection. For each variable, temporal changes in injection and production wells and spatial distributions of relative saturations in the organic phase were compared. Cleanup time and cumulative organic recovery were also quantified. The study would provide useful information to design strategies for the remediation of nonaqueous phase liquid-contaminated aquifers.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.4
• /
• pp.617-626
• /
• 2006

Compared with the sludge from gravity sedimentation, it is difficult for operations to settle the sludge occurred from dissolved-air-flotation (DAF). Even though there are some problems in treating DAF sludge with conventional gravity thickeners, those has been used until now. In this study, Solid Flux theory for gravity thickening was applied to the Solid Flux of DAF sludge through flotation in order to develop new methodology for treatment of DAF sludge. Also, characteristics of DAF sludge were investigated. From the experiment results, it was revealed that the higher the polymer dosage, at fixed the solid concentration, the greater the rising velocity becomes. When we applied solid flux theory, the relationship, which is similar to that of gravity thickening, has been achieved. Also, we could find the proper polymer dosage from the rising velocity is about 50 mg/L. Consequently, the limiting solid flux can be derived from the relationship between the total solid flux and the withdrawal velocity of DAF sludge. Furthermore, the factors, such as solid concentrations, bubble volume, pH, zeta potential, and temperature, have effects on the flotation and sedimentation for DAF sludge treatment.