• Journal of Industrial Technology
• /
• v.24 no.A
• /
• pp.119-126
• /
• 2004

BLDC Motor is one of the widely utilizable motors in servo system. The accurate calculation of the power loss for the IGBT and Inverse diode with Bipolar and Unipolar switching modes the driving modes is important for the design of drives for their heat treatment. If it were not for temperature-sensors in devices, it is difficult to get direct power loss, so. Power losses may be modeled by computer modeling to obtain the Calculation of the Power loss for Inverter in BLDC Motor with switching modes which is presented in this paper. The computer modeling is carried out by Matlab simulation. The power loss consists of conduction losses Conduction losses are the source of occurrence due to The IGBT and Inverse diode currents. Switching losses are the source of occurrence due to switching on/off in the devices, and gives the dominant influence to the loss. As a result, the unipolar I mode is best in reducing the heat losses.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.1
• /
• pp.62-68
• /
• 1989

In this paper, Analog/Digital BCDMOS technology that the bipolar devices for driver applications CMOS devices for logic applications, and DMOS devices for high voltage applications is pressented. An optimized poly-gate p-well CMOS process is chosen to fabricate the BCDMOS, and the basic concepts to desigh these devices are to improve the characteristics of bipolar, CMOS & DMOS with simple process technology. As the results, $h_{FE}$ value is 320 (Ib-$10{\mu}A$ for bipolar npn transistor, and there is no short channel effects for CMOS devices which have Leff to $1.25{\mu}m$ and $1.35{\mu}m$ for n-channel and p-channel, respectively. Finally, breakdown voltage is obtained higher than 115V for DMOS device.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.790-797
• /
• 2015

In this paper, We made the microwave polar transmitter based on the software to analyze the synchronization status between the phase signal and the amplitude signal of polar transmitter, and analyzed the result. In order to solve the time delay mismatch problem, we applied simplified compensation algorithm and compared the synchronization status between the two paths before and after compensation. Before compensation, the value of time delay mismatch was the maximum of 97 nsec at 9.3 GHz with the occupied bandwidth of 12 MHz, but after applying the compensation algorithm, the signals between the two paths were synchronized, and we identified the occupied bandwidth could recover to the previous 3.7 MHz.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.39 no.1
• /
• pp.40-48
• /
• 2002

Three-Dimensional scene reconstruction from images acquired with different viewpoints is possible as estimating Fundamental matrix(F-matrix) that indicates the epipolar geometry of two images. Correspondence points required to calculate F-matrix of two images include noise such as miss matches, so generally it is hard to calculate F-matrix accurately. In this paper, we classify noise into two types; outlier and minute noise. we propose SSOR algorithm that estimate F-matrix effectively. SSOR algorithm is rejecting outlier step by step in a noise environment. To evaluate the performance of proposed algorithm we simulated with synthetic images and real images. As a result of simulation we show that proposed algorithm is better than conventional algorithms.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.93-98
• /
• 2005

Silicon bipolar transistors (Si-BJT) are widely used in the telecommunication system such as short range wireless control and wireless indoor voice communication system. New modeling method for the internal current source model of Si-BJT is proposed. The proposed method based on new thermal resistance extraction method and new analytical expressions for the current source parameters of Si-BJT. The proposed method can directly extract the model parameters without any optimization procedure which is adopted in the conventional modeling method. The proposed method is applied to 5 finger $0.4\times20[{\mu}m^2]$ and the model shows good prediction of the measured data in $3[\%]$ of errors proving the validity of this method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1C
• /
• pp.83-91
• /
• 2004

An epipolar rectification is the process of transforming the epipolar geometry of a pair of images into a canonical form. This is accomplished by applying a homography to each image that maps the epipole to a predetermined point. In this process, rectified images transformed by homographies must be satisfied with the epipolar constraint. These homographies are not unique, however, we find out homographies that are suited to system's purpose by means of an additive constraint. Since the rectified image pair be a stereo image pair, we are able to find the disparity efficiently. Therefore, we are able to estimate the three-dimensional information of objects within an image and apply this information to object segmentation. This paper proposes a rectification method for object segmentation and applies the rectification result to the object segmentation. Using color and relative continuity of disparity for the object segmentation, the drawbacks of previous segmentation method, which are that the object is segmented to several region because of having different color information or another object is merged into one because of having similar color information, are complemented. Experimental result shows that the disparity of result image of proposed rectification method have continuity about unique object. Therefore we have confirmed that our rectification method is suitable to the object segmentation.

• Journal of Korean Electronics
• /
• v.3 no.1
• /
• pp.75-81
• /
• 1983

• The monthly packaging world
• /
• s.223
• /
• pp.82-85
• /
• 2011

• The Korean Publising Journal, Monthly
• /
• s.335
• /
• pp.26-28
• /
• 2003

• Proceedings of the KIEE Conference
• /
• 2008.04a
• /
• pp.242-243
• /
• 2008

사다리꼴 역기전력을 갖는 BLDC 전동기 제어는 구형파 전류를 인가함으로서 DC 모터와 같은 제어를 할 수 있어 많은 응용 분야에 사용되고 있다. 구형파 전류를 인가하기 위하여 연구된 PWM방식을 분석해 보면 몇 가지 문제점을 가지고 있다. 기존의 연구내용으로는 유니폴라 PWM방법, 바이폴라 PWM 방법, 하이브리드 PWM 방법이 있으나 PWM을 정확히 분석해보면 원하는 전압을 인가할 수 없는 부분이 있음을 알 수 있다. 특히 방향을 바꾸는 시점이나 속도를 급격히 줄이는 부분에서는 원하는 전압이 인가되지 않음을 알 수 있다. 본 논문에서는 이러한 문제점을 분석하고 정확한 전압이 인가될 수 있는 방법을 제안한다.