• Journal of the Korea Convergence Society
• /
• v.8 no.4
• /
• pp.199-205
• /
• 2017

In this study, the design analysis and the explosion welding were made into a clad sheet by the convergence method in order to solve the problem of heat transfer to the guide due to the heating of the 3D printer heating block. The shear strength of the clad plate material was tested and the results were analyzed by thermal analysis, thermal conductivity and thermal imaging. The following conclusions were obtained. 3D modeling of the heating block made of copper and titanium clad plate material The thermal analysis showed that the surface temperature of the filament guide area was lower than the heating block surface temperature. The average shear strength of copper and titanium clad plate material was measured and the average value of 195.6MPa was obtained. The thermal conductivity of the heating block made of copper and titanium clad plate material was measured three times and the average value was $62.52W/m{\cdot}K$. The surface temperature of the heating block made of copper and titanium clad plate material was measured by a thermal imaging camera at a maximum of $107.3^{\circ}C$ and $183.2^{\circ}C$ at the filament guide. The temperature distribution was $89^{\circ}C$ lower than that of the existing filament.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.4
• /
• pp.263-270
• /
• 2017

The shipbuilding industry uses large stationary tanks to store low-pressure air, which is used to open and close large shut-off valves. However, when supplying air from the tank to a distant valve, there are problems related to the need for supplementary pipes and the pressure drop during transportation. In this study, a portable welded vessel for storing high-pressure nitrogen (11 kg, 10 L, and 50 bar) was designed to prevent air leakage and improve the convenience of workers. This pressure vessel was elliptical to reduce the number of welded parts, which are structurally weak. The thickness and ratio of the major and minor axes of the pressure vessel were calculated to verify its structure stability at the working pressure (50 bar), and that the proposed weight and capacity were satisfactory. The residual stress caused by the welding process was calculated by performing a transient thermal-structural coupled field analysis using the ANSYS parametric design language (APDL), and the fatigue life of the vessel was verified based on the Goodman criterion.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.6
• /
• pp.371-383
• /
• 2021

Steel-concrete single-leaf blast-resistant doors, having steel box and slab inside, are installed on the wall using supporting members such as hinges and latches. Several studies have been conducted on their deflection behavior in the same direction as that of the blast pressure, but studies on their deflection behavior in the opposite direction, that is, studies on negative deflection behavior are relatively insufficient. In this study, we conducted a parameter analysis using finite element analysis on blast-resistant doors, on their rebound behavior in the negative deflection phase. Results revealed that the plastic deformation of the door, and the change in momentum and kinetic energy during rebound, were major factors influencing the rebound behavior. Greater rebound force was developed on the supporting members in the impulsive region, than in the quasi-static region; due to the characteristics in the impulsive region, where the kinetic energy developed relatively greater than the strain energy. In the design process, it is necessary to consider excessive deformation that could occur in the supporting members as the rebound behavior progresses. Additionally, it was found that in the case of steel-concrete blast doors, the rebound force increased relatively more, when the effects of both rebound and negative blast pressure contributed to the negative deflection of the door. Since conditions for the occurrence of this superposition effect could vary depending on structural characteristics and explosion conditions, further investigation may be required on this topic.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.11
• /
• pp.107-118
• /
• 2022

The social need for stable hydrogen storage technologies that respond to the increasing demand for hydrogen energy is increasing. Among them, underground hydrogen storage is recognized as the most economical and reasonable storage method because of its vast hydrogen storage capacity. In Korea, low-depth hydrogen storage using artificial protective structures is being considered. Further, establishing corresponding safety standards and ground stability evaluation is becoming essential. This study evaluated the hydro-mechanical behavior of the ground during a hydrogen gas leak from a low-depth underground hydrogen storage facility through the HM coupled analysis model. The predictive reliability of the simulation model was verified through benchmark experiments. A parameter study was performed using a metamodel to analyze the sensitivity of factors affecting the surface uplift caused by the upward infiltration of high-pressure hydrogen gas. Accordingly, it was confirmed that the elastic modulus of the ground was the largest. The simulation results are considered to be valuable primary data for evaluating the complex analysis of hydrogen gas explosions as well as hydrogen gas leaks in the future.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.36 no.4
• /
• pp.273-282
• /
• 2023

Probabilistic safety assessment (PSA) has been widely used to evaluate the seismic risk of nuclear power plants (NPPs). However, studies on seismic PSA for process plants, such as gas plants, oil refineries, and chemical plants, have been scarce. This is because the major disasters to which these process plants are vulnerable include explosions, fires, and release (or dispersion) of toxic chemicals. However, seismic PSA is essential for the plants located in regions with significant earthquake risks. Seismic PSA entails probabilistic seismic hazard analysis (PSHA), event tree analysis (ETA), fault tree analysis (FTA), and fragility analysis for the structures and essential equipment items. Among those analyses, ETA can depict the accident sequence for core damage, which is the worst disaster and top event concerning NPPs. However, there is no general top event with regard to process plants. Therefore, PSA cannot be directly applied to process plants. Moreover, there is a paucity of studies on developing fragility curves for various equipment. This paper introduces PSA for gas plants based on FTA, which is then transformed into Bayesian network, that is, a probabilistic graph model that can aid risk-informed decision-making. Finally, the proposed method is applied to a gas plant, and several decision-making cases are demonstrated.

• Korean Journal of Optics and Photonics
• /
• v.27 no.1
• /
• pp.18-24
• /
• 2016

To effectively utilize a flash and predict its effects on an infrared device, it is essential to know the infrared characteristics of the flash source. In this paper, a study of the IR characteristics of flash light sources is carried out. The IR characteristics of three flash sources, of which two are combustive and the other is explosive, are measured with an IR characteristic measurement system over the middle- and long-wavelength infrared ranges. From the measurements, the radiances over the two IR ranges and the radiative temperatures of the flashes are extracted. The IR radiance of flash A is found to be the strongest among the three, followed by those of sources C and B. It is also shown that the IR radiance of flash A is about 10 times stronger than that of flash B, even though these two sources are the same type of flash with the same powder. This means that the IR radiance intensity of a combustive flash source depends only on the amount of powder, not on the characteristics of the powder. From the measured radiance over MWIR and LWIR ranges for each flashes, the radiative temperatures of the flashes are extracted by fitting the measured data to blackbody radiance. The best-fit radiative temperatures (equivalent to black-body temperatures) of the three flash sources A, B, and C are 3300, 1120, and 1640 K respectively. From the radiance measurements and radiative temperatures of the three flash sources, it is shown that a combustive source radiates more IR energy than an explosive one; this mean, in turn, that the effects of a combustive flash on an IR device are more profound than those of an explosive flash source. The measured IR radiances and radiative temperatures of the flash sources in this study can be used to estimate the effects of flashes on various IR devices, and play a critical role for the modeling and simulation of the effects of a flash source on various IR devices.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.62-66
• /
• 2016

We designed a model composed a ring type magnet, a yoke, and a sensing coil buried in a projectile for calculating the muzzle velocity based on the voltage induced from sensing coil by simulation. The muzzle velocity was calculated from the master curve obtained through the voltage induced from sensing coil by simulation. The induced voltage increased with increasing the diameter of sensing coil. The projectile's velocity was proportional to the induced voltage when the sensing coil was buried in projectile. The projectile will be surely exploded at the target region by inputting the information of muzzle velocity variation corrected the diameter effect of induced voltage of sensing coil.

• KIPS Transactions on Software and Data Engineering
• /
• v.5 no.5
• /
• pp.221-230
• /
• 2016

With emerging the Internet of Things (IoT) paradigm, the sensor network and sensor platform technologies have been changed according to exploding amount of sensors. Sensor Registry System (SRS) as a sensor platform is a system that registers and manages sensor metadata for consistent semantic interpretation in heterogeneous sensor networks. However, the SRS is unsuitable for the IoT environment. Therefore, this paper proposes sensor registry data model to register and manager sensor information in the IoT environment. We analyze Semantic Sensor Network Ontology (SSNO) for improving the existed SRS, and design metamodel based on the analysis result. We also build tables in a relational database using the designed metamodel, then implement SRS as a web application. This paper applies the SSNO and sensor ontology examples with translating into the proposed model in order to verify the suitability of the proposed sensor registry data model. As the evaluation result, the proposed model shows abundant expression of semantics by comparison with existed models.

• Journal of Astronomy and Space Sciences
• /
• v.24 no.2
• /
• pp.135-144
• /
• 2007

Space environment becomes more hazardous for satellite because of increasing number of space debris. This research is to analyze collision hazards between KOMPSAT 3 in low-earth orbit and space debris generated by the explosion of FengYun satellite on the January 11, 2007. Based on the observed data of the space debris from FengYun satellite, the mass and number distribution of the debris are estimated including undetectable debris from the explosion of FengYun satellite. The spatial density and flux for the space debris can be calculated according to size. This study also brings out the analysis for the assessment of collision probability and damage probability. The algorithm developed in the current paper can be used to estimate the level of risk due to space debris for the satellites that will be launched in the future.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.9
• /
• pp.720-725
• /
• 2013

Nylon wire cutting method by nichrome wire is generally applicable for cube satellite applications due to its advantages of simplicity. However, the system complexity is not avoidable to apply it on the cube satellite with multi-deployable structures. A lower constraint force of the mechanism is also one of the disadvantages of the mechanism. In this study, we proposed a preliminary structure design of cube satellite with the separation mechanism which is applicable for holding and release of the multi-deployable structures. The effectiveness of the mechanism design was verified through function test of EM mechanism. The structure analysis results showed that the structure design proposed in this study is feasible.