• Journal of the Korean Magnetics Society
• /
• v.13 no.5
• /
• pp.198-203
• /
• 2003

To investigate whether the use of hard magnetic film is available to generate bias magnetic field for a magnetoimpedance sensor, the magnetic properties of SmCo hard magnetic films were investigated as a function of their compositions. The saturation magnetization decreased with Sm content increasing in SmCo films. And, the coercive force increased in the extent of Sm content of 28 at%, but decreased as Sm content increased moreover. The bias field effect of SmCo film to amorphous CoZrNb film was investigated with the magnetization corves, permeabilities, and magnetic domain structures of SmCo/CoZrNb multilayers. The bias field of about 60 Oe was observed in the film with 3 mm ${\times}$ 0.5 mm, which can be constructed as a MI sensor, and this result strongly indicates that the bias field generated from a hard magnetic film is adequate to enhance the sensitivity of a MI sensor with hard/soft magnetic multilayer structure.

• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.249-254
• /
• 1998

In relation to the application of magnetic method to the evaluation of irradiation damage (embrittlement) changes in the magnetic parameters(hysteresis loop and Barkhausen noise) and Vickers microhardness due to neutron irradiation and heat treatment were measured and compared. In the case of irradiation $(2.3{\times}10^{19}\;n/cm^2,\; E{\ge}1\;Mev,\; 288{\circ}C)$ hysteresis loop measurements show that susceptibility decreases as coercivity increase. Saturation magnetization do not show any change. Barkhausen noise amplitude and Barkhausen noise energy have decreased while Vickers microhardness has increased. For isothermally heat treated condition of irradiated specimen at 470 $^{\circ}C$ and 540 $^{\circ}C$, Barkhausen noise energy has increased while Vickers microhardness has decreased. Results of BNE and Vickers microhardness are reversed to the results on irradiated condition. All these consistent changes in magnetic parameter and Vickers microhardness measurement, which are thought to be resulted from the interaction between irradiation-induced defects and dislocation, and magnetic domain, respectively, show a possibility that magnetic measurement may be used to the evaluation of material degradation and recovery due to neutron irradiation and heat treatment, respectively, if a relevant large database in prepared.

• Journal of Korea Water Resources Association
• /
• v.35 no.1
• /
• pp.65-75
• /
• 2002

The objectives of this study are to analyse model-based soil moisture variations depending on model parameters m and $T_0$ and to evaluate the model performance for the simulation of soil moisture variations by the comparison of observed groundwater levels and model-driven soil moisture amounts and observed and simulated river discharges at the basin outlet. The selected study area is the Pyungchang IHP river basin with outlet at Sanganmi station and the summer flooding events during '94-'98 are used for the analysis. As a result, soil moisture holding capacity is increased according to increase the parameter m that represents effective groundwater depth. This phenomenon is especially dominant when higher m and $T_0$ values are used. The qualitative comparison of computed base flow and observed groundwater level shows that the base flow peaks are reasonably simulated and the decreasing limbs of hydrograph are mainly caused by base flows. It is concluded that TOPMODEL can be used effectively for simulating basin-averaged soil moisture variations in addition to river flow generations.

• Nuclear Engineering and Technology
• /
• v.27 no.4
• /
• pp.503-517
• /
• 1995

A mechanistic model for forced convective transition boiling has been developed to predict transition boiling heat flux realistically. This model is based on a postulated multi­stage boiling process occurring during the passage time of an elongated vapor blanket specified at a critical heat flux condition. Between the departure from nucleate boiling (DNB) and the departure from film boiling (DFB) points, the boiling heat transfer is established through three boiling stages, namely, the macrolayer evaporation and dryout governed by nucleate boiling in a thin liquid film and the unstable film boiling. The total heat transfer rate during the transition boiling is the sum of the heat transfer rates after the DNB weighted by the time fractions of each stage, which are defined as the ratio of each stage duration to the vapor blanket passage time. The model predictions are compared with some available experimental transition boiling data. From these comparisons, it can be seen that the transition boiling heat fluxes including the maximum heat flux and the minimum film boiling heat flux are nil predicted at low qualities/high pressures near 10 bar.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.142-142
• /
• 2010

본 논문은 단결정 및 다결정 실리콘 기판 상에 아산화질소 플라즈마 처리를 통하여 형성한 초박형 실리콘 옥시나이트라이드 박막의 특성과 이의 어플리케이션에 관한 것이다. 초박형 절연막은 현재 다양한 전자소자의 제작과 특성 향상을 위하여 활용되고 있으나 일반적인 화학 기상 증착 방법으로는 균일도를 확보하기 어려운 문제점을 가지고 있다. 디스플레이의 구동소자로 활용되는 박막 트랜지스터의 특성 향상과 비휘발성 메모리 소자의 터널링 박막에 응용하기 위하여 초박형 실리콘 옥시나이트라이드 박막의 증착과 이의 특성을 분석하였고, 실제 어플리케이션에 적용하였다. 실리콘 산화막과 실리콘 계면상에 존재하는 질소는 터널링 전류와 결함 형성을 감소시키며, 벌크 내에 존재하는 질소는 단일 실리콘 산화막에 비해 더 두꺼운 박막을 커패시턴스의 감소없이 이용할 수 있는 장점이 있다. 아산화질소 플라즈마를 이용하여 활성화된 질소 및 산소 라디칼들이 실리콘 계면을 개질하여 초박형 실리콘 옥시나이트라이드 박막을 형성할 수 있다. 플라즈마 처리 시간과 RF power의 변화에 따라 형성된 실리콘 옥시나이트라이드 박막의 두께 및 광학적, 전기적 특성을 분석하였다. 아산화질소 플라즈마 처리 방법을 사용한 실리콘 옥시나이트라이드 박막을 시간과 박막 두께의 함수로 전환해보면 초기적으로 증착률이 높고 시간이 지남에 따라 두께 증가가 포화상태에 도달함을 확인할 수 있다. 아산화질소 플라즈마 처리 시간의 변화에 따라 형성된 박막의 전기적인 특성의 경우, 플라즈마 처리 시간이 짧은 실리콘 옥시나이트라이드 박막의 경우 전압의 변화에 따라 공핍영역에서의 기울기가 현저히 감소하며 이는 플라즈마에 의한 계면 손상으로 계면결합 전하량이 증가에 기인한 것으로 판단된다. 또한, 전류-전압 곡선을 활용하여 측정한 터널링 메카니즘은 2.3 nm 이하의 두께를 가진 실리콘 옥시나이트라이드 박막은 직접 터널링이 주도하며, 2.7 nm 이상의 두께를 가진 실리콘 옥시나이트라이드 박막은 F-N 터널링이 주도하고 있음을 확인할 수 있다. 결론적으로 실리콘 옥시나이트라이드 박막을 활용하여 전기적으로 안정한 박막트랜지스터를 제작할 수 있었으며, 2.5 nm 두께를 경계로 터널링 메커니즘이 변화하는 특성을 이용하여 전하 주입 및 기억 유지 특성이 효과적인 터널링 박막을 증착하였고, 이를 바탕으로 다결정 실리콘 비휘발성 메모리 소자를 제작하였다.

• Journal of the Korean Vacuum Society
• /
• v.22 no.4
• /
• pp.211-217
• /
• 2013

Two types of organic thin film solar cell devices with bulk hetero-junction (BHJ) structure were fabricated on plastic substrates using conjugated polymers of $PCDTBT:PC_{71}BM$ and $PTB7:PC_{71}BM$ blended as active channel layer. Time-variant characteristics of the organic thin film solar cell devices were investigated: short circuit current density ($J_{SC}$); open circuit voltage ($V_{OC}$); ; fill factor (FF); power conversion efficiency (PCE, ŋ). All the performance parameters were degraded by progress of the measurement time, while $V_{OC}$ showed the most drastic decrease with time. Possible factors to cause the time-variant alteration of performance parameters were discussed to be clarified.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.3
• /
• pp.534-540
• /
• 2008

The adaptive learning circuit is designed on the basis of modeling of MFSFET (Metal-Ferroelectric-Semiconductor FET) and the numerical results is analyzed. The output frequency of the adaptive learning circuit is inversely proportional to the source-drain resistance of MFSFET and the capacitance of the circuit. The saturated drain current with input pulse number is analogous to the ferroelectric polarization reversal. It indicates that the ferroelectric polarization plays an important role in the drain current control of MFSFET. The output frequency modulation of the adaptive learning circuit is investigated by analyzing the source-drain resistance of MFSFET as functions of input pulse numbers in the adaptive learning circuit and the dimensionality factor of the ferroelectric thin film. From the results, adaptive learning characteristics which means a gradual frequency change of output pulse with the progress of input pulse, are confirmed. Consequently it is shown that our circuit can be used effectively in the neuron synapses of neural networks.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.216-216
• /
• 2017

제주지역의 하천은 일정강우 이상 발생 시 하천 표층이 포화된 후 갑작스러운 유출이 발생되며, 강우에 의해 점진적으로 하천유량이 증가하는 내륙지역 하천과는 다른 유출특성을 보인다. 그러나 제주지역 하천특성에 관한 연구는 최근부터 진행되어 현재까지도 내륙지역의 하천계획의 방법을 적용되고 있다. 이 연구에서는 제주도 한천유역을 대상으로 국내에서 적용되는 설계홍수량 산정방법을 적용하여 문제점을 도출하고, 지형 및 지역특성을 분석하여 설계홍수량 산정 시 매개변수의 적용방안을 개선하였다. 홍수량 검증을 위해 보유하고 있는 현장관측 자료 중 가장 큰 첨두유량이 발생한 3개의 사상을 선정하여 비교하였다. 기존 홍수량 산정방법을 이용하여 한천유역의 유출량을 산정한 결과 78.7 ~ 317.8 cms, 14.3 ~ 37.5%의 오차율로 관측자료 대비 큰 오차를 범하는 것으로 검토되었다. 한천유역의 상류지역은 45%로 매우 급한 경사형태를 보이고, CN산정 시 경사보정을 통해 홍수량을 산정한 결과 기존의 유출특성 대비 1.47 ~ 6.45% 개선되었다. 관측자료 기반 강우-유출의 최적화 기법을 통해 산정된 도달시간을 적용하여 홍수량을 산정한 결과 4.39 ~ 16.67% 개선되었으며, 한천유역을 소유역으로 구분하여 홍수량을 산정한 결과 9.92 ~32.96% 개선된 결과가 도출되었다. 이러한 결과는 지역별 함양특성과 급한 경사 특성, 토지이용에 따른 유역특성이 적용되고, 지역별 초기손실이 반영되어 홍수유출곡선이 실제 관측자료와 유사하게 나타나는 것으로 기존방법의 경우 전체 유역에 평균값이 일괄적으로 적용되기 때문에 실제관측자료와 큰 오차를 나타내는 것으로 분석되었다.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.68-74
• /
• 2021

Gas diffusion layer (GDL) compression is important parameter of polymer electrolyte membrane fuel cell (PEMFC) performance to have an effect on contact resistance, reactants transfer to electrode, water content in membrane and electrode assembly (MEA). In this study, the effect of GDL compression on fuel cell performance was investigated for commercial products, JNT20-A3. Polarization curve and electrochemical impedance spectroscopy was performed at different relative humidity and compression ratio using electrode area of 25 ㎠ unit cell. The contact resistance was reduced to 8, 30 mΩ·㎠ and membrane hydration was increased as GDL compression increase from 18.6% to 38.1% at relative humidity of 100 and 25%, respectively. It was identified through ohmic resistance change at relative humidity conditions that as GDL compression increased, water back-diffusion from cathode and electrolyte membrane hydration was increased because GDL porosity was decreased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.3
• /
• pp.59-70
• /
• 2020

Obtaining external forced convection heat transfer from bubble boiling and validating it with experimental results using cryogenic liquids are suggested to derive total heat transfer coefficient with pool boiling condition in the case of coil type heat exchanger with a bundle of tubes and to overcome the limitation of using the empirical correlation. Experiment is conducted with pool boiling heat transfer of saturate liquid nitrogen with helical coil type heat exchanger using liquid oxygen as hot stream fluid. Experimentally measured heat transfer coefficient is well-agreed with the estimated curve considering nucleate boiling and forced convection induced by bubble rise.