• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.6
• /
• pp.470-477
• /
• 2017

As a method of the transmission efficiency improvement of an aperture smaller than the wavelength, we modified the conventional H-shaped resonant aperture to lower the resonance frequency of resonant aperture, and the transmission efficiency of resonant aperture was improved more than the conventional aperture. The maximum transmission cross section(TCS) calculated using the equivalent circuit tends to be almost equal to the maximum TCS from the small resonant aperture modified to improve the transmission efficiency. The transmission characteristics of resonant apertures can be quantified as the TCS, and the transmission efficiency of that can be compared. The modified resonant aperture has a maximum TCS increased by about 2.87 times from $846mm^2$ to $2,431mm^2$ compared to the H-shaped aperture, and the resonant frequency decreased from 5.06 GHz to 2.92 GHz, and the length-to-wavelength ratio of the aperture was reduced from 0.178 to 0.103.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.5
• /
• pp.459-465
• /
• 2015

There exist different kinds of aircrafts, such as conventional airplane, rotorcraft, fighter, and unmanned aerial vehicle. Their shape and feature are dependent upon their own assigned mission. One of the fundamental analyses performed during the aircraft design is the structural analysis. It becomes more complicated and requires severe computations because of the recent complex trends in aircraft structure. In order for efficiency in the structural analysis, a simplified approach, such as equivalent beam or plate model, is preferred. However, it is not clear which analysis will be appropriate to analyze the realistic configuration, such as an aircraft wing, i.e., between an equivalent beam and plate analysis. It is necessary to assess the limitation for both the one-dimensional beam analysis and the two-dimensional plate theory. Thus, in this paper, the static structural analysis results obtained by EDISON solvers were compared with the three-dimensional results obtained from MSC NASTRAN. Before that, EDISON program was verified by comparing the results with those from MSC NASTRAN program and other analytic solutions.

• Elastomers and Composites
• /
• v.35 no.1
• /
• pp.29-37
• /
• 2000

In this study as a basic research of the elastomer, we show the results of the behavior of the two different chain length polymers in the melt confined between two impenetrable planes. The cubic lattice simulations are conducted in the canonical ensemble with a method that is a combination of reptation and crackshaft bond flip motions. A total of 680 chains which are 544 short chains comprising 10 beads and 136 long chains comprising 160 beads were placed in 20 lattice layers. It was assumed that there is no energetic interactions between covalently connected beads. while all other neighbors will interact with a truncated 6-12 Lennard-Jones potential. From the analysis of the simulation results, it was shown that purely entropic effects caused the shorter chains to partition preferentially to the surface. We also showed that the center of mass density of the shorter chains shows maximum near the surface. This is the opposite phenomena when compared to that of the longer chains. However, the segments of the shorter and the longer chains did not display any significant changes in bond order.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.3
• /
• pp.243-247
• /
• 2015

The characteristics of the fluid force reduction of a square prism having a small triangular prism at the upstream side was investigated by measuring of lift and drag on the square prism The experimental parameters were the width ratios (H/B=0.2~0.6) of triangular prisms to the prism width and the gap ratios (G/B=0~3) between the square prism and the triangular prism. The drag reduction rate of the square prism was increased and then decreased with G/B in case of the same H/B, and was increased with H/B in case of the same G/B. The maximum drag reduction rate was represented by 78.5% at H/B=0.6 and G/B=1.5. The lift reduction rate of the square prism was hardly not affected by the width and gaps ratios, the average value was about 52.4%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.757-764
• /
• 2014

In this study, the effect of shape parameters on the J-R curves of curved CT specimens was evaluated using the limit load method. Fracture toughness tests considering the shape factors L/W and $R_m/t$ of the specimens were also performed. Thereafter, the J-R curves of the curved CT specimens were compared using the J-integral equation proposed in the ASTM (American Society for Testing and Materials) and limit load solution. The J-R curves of the curved CT specimens were also compared with those of the CWP (curved wide plate), which is regarded to be similar to real pipe and standard specimens. Finally, the effectiveness of the J-R curve of each curved CT specimen was evaluated. The results of this study can be used for assessing the applicability of curved CT specimens in the accurate evaluation of the fracture toughness of real pipes.

• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.179-186
• /
• 1993

Heat pipes. applied to a flat plate solar collector, have a long and slender configuration with relatively low heat flux in the evaporator section. Such a heat pipe has a tendency to build-up a liquid pool at the lower part of the evaporator section. and at this pool occurs such complicated phenomena of evaporation and fluid dynamics as superheat, sudden generation of bubble, its likely explosive growth process and flooding, etc. In the present study. we tried to solve these problems by means of adjusting two principal design parameters, the liquid inventory and the installation region of the wick, using 4 heat pipes and 3 thermospheres. The corresponding results can be summarized as follows$\^$1)/. The effective thermal conductances of the heat pipe was greatly improved by eliminating the wick in the adiabatic and condenser sections$\^$2)/. The liquid inventory should be increased by about 40% larger than what is saturated the wick$\^$3)/. In the evaporator section the wick has a favorable effect to reduce both unstable operation by intermittent occurrence of nucleate boiling and response time at the initial start-up process.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.368-371
• /
• 2020

In this paper, we propose a linear tapered slot rectifying antenna for a portable UHF-band RFID system. Since the proposed rectifying antenna does not use a dielectric substrate, the planar antenna is implemented with a thin metal thickness. The rectifier circuit converts input RF power into output DC voltage using a voltage doubler circuit based on two anti-parallel schottky diodes. The rectifying antenna is integrated by the voltage doubler circuit into a linear tapered slot antenna. For conjugate impedance matching of the rectifying circuit and the linear tapered slot antenna, the source-pull method was utilized by adjusting the angle of the tapered slot and the length of the antenna feed line. The proposed antenna prototype has been verified with the electrical and radiation characteristics through RF-DC conversion and far-field radiation test in open space measurement environment. Finally, the proposed antenna is realized to 0.23-wavelength (75 mm) and 0.18-wavelength (60 mm) at 915 MHz center frequency.

• Computational Structural Engineering
• /
• v.9 no.2
• /
• pp.133-142
• /
• 1996

In this paper, two different techniques for mixed-mode type engineering fracture mechanics are investigated to estimate the stress intensity factors by using p-version finite element model. These two techniques are displacement extrapolation with COD and CSD method and J-integral with decomposition method. By decomposing the displacement field obtained from p-version of finite element analysis into symmetric and antisymmetric displacement fields with respect to the crack line, Mode-I and Mode-II stress intensity factors can be determined using aforementioned techniques. The example problems for validating the proposed techniques are centrally and centrally oblique cracked panels under tension. The numerical results associated with the variation of oblique angle and the ratio of crack length and panel width (a /W ratio) are compared with those by theoretical values and empirical solutions in literatures. Very good agreements with the existing solutions are shown.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.3
• /
• pp.130-134
• /
• 2005

To the best knowledge, the formation and characterization of InSb nanowires have not been reported yet in spite of its good characteristics as a III-V compound semiconductor. The nanowire arrays were potentiostatically electrodeposited in a mixing solution of indium chloride, antimony chloride, citric acid, and potassium citrate according to our previous work on the electrodeposition of the stoichiometric InSb films. The electrical properties of nanowire arrays were measured by semiconductor parameter analyzer, and the microstructural analysis of the nanowires was conducted by employing XRD. Our experimental results indicate that the InSb nanowires have a highly preferred orientation of (220) direction and also exhibit electrical characteristics of n-type semiconductors which we, however, similar to semi-metals mainly due to their narrow band-gap and high electron mobility.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.296-302
• /
• 2009

In this paper, a planar microstrip patch antenna is proposed using the slit on the top layer of a multi-layered structure for GPS application. The proposed antenna has a circular polarization at 1,575.42 MHz. This proposed antenna is fabricated on multi-layered FR4 substrate. The slits embedded on the top plane may yield to lower a resonance frequency and sustain a broad bandwidth. The proposed antenna size is $20{\times}20{\times}4.0\;mm^3$. The measured gain of 0.5 dBi, 10 dB bandwidth(VSWR 2:1) of 70 MHz(4.4 %), and 3 dB axial-ratio bandwidth of 15 MHz(1 %) have been obtained, respectively.