• Transactions of Materials Processing
• /
• v.7 no.2
• /
• pp.177-185
• /
• 1998

The kinematically admissible veolcity field is developed for the shapes of dead metal zone and the curving velocity distribution in the eccentric plane dies extrusion. The shape of dead metal zone is defined as the boundary surface with the maximum friction constant between the deformable zone and the rigid zone. The curving phenomenon in the eccentric lane dies is caused by the eccentricity of plane dies. The axial velocity distribution in the plane dies is divided in to the uniform velocity and the deviated velocity. The deviated velocity is linearly changed with the distance from the center of cross-section of the workpiece. The results show that the curvature of products and the shapes of the dead metal one are determined by the minimization of the plastic work and that the curvature of the extruded products increase with the eccentricity.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.5
• /
• pp.372-377
• /
• 2007

This paper proposes a novel fault diagnosis method of a electrolytic capacitor used for DC-link voltage smoothing in adjustable speed drives. The equivalent series resistance (ESR) of the electrolytic capacitor is directly estimated from DC-link voltage and load currents and the status of the electrolytic capacitor is determined from the estimated ESR. To compensate the variation of the ESR owing to temperature variation, diodes are located on the same PCB near the capacitor and the temperature of the capacitor is sensed indirectly from the voltage drop of diodes. Simulation and experimental studies show the effectiveness of the proposed method.

• New & Renewable Energy
• /
• v.18 no.3
• /
• pp.23-31
• /
• 2022

This study evaluated the potential of coffee waste (CW) and used frying oil (UFO) as an additive in the production of pitch pine (PIP) and Mongolian oak (MOK) pellets. Ash contents obtained from CW and UFO were 0.5% and <0.1%, respectively. The calorific values of UFO (31.4 MJ/kg) and CW (26.3 MJ/kg) are higher than PIP (20.6 MJ/kg) and MOK (19.1 MJ/kg). For pellets fabricated using a pilot-scale flat-die pellet mill, regardless of fabricating conditions, moisture content (MC) and bulk density of PIP and MOK pellets satisfied the A1 wood pellet standard for residential and small-scale commercial uses, as designated by the National Institute of Forest Science (NIFOS) of the Republic of Korea. When CW was used as an additive, durability of PIP pellets made with 12%-MC sawdust and MOK pellets increased. The optimal conditions for producing PIP and MOK pellets could be by adding 20 mesh CW as an additive and the using of 12%-MC sawdust. However, durability of PIP pellets and ash content MOK pellets did not satisfy the A1 wood pellet standard of NIFOS. Thus, further research is needed to improve the properties of wood pellets with additives.

• The Hankook-Saengyark Bo
• /
• no.242
• /
• pp.2-2
• /
• 2000

각종 국제행사 맞아 '세계속 경동약령시로' - 중국, 한약재 전략산업화 적극 추진(사천성에 2백만평 규모 종합단지 조성 계획) - 한$\cdot$중 공동 심포지움 개최(한국약용작물학회) - '홍삼, 다이어트에 좋아요' 인삼연 제품개발, 부작용 적어

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.242-247
• /
• 1998

The conventional closed-die forging processes had been applied to forging of the spur gears. But this type process requires high pressure. The commercial finite element analysis code ANSYS for the stress and elastic deformation of non-axisymmetric die was adopted in this study. In the non-axisymmetric die such as gear forging, maximum stresses were imposed on the tip of the gear tooth. When the stress exceeds yield strength of insert die, many approaches were attemped to prevent the die failure. Good shaped products are forged successfully. This type process could by used as an advanced technique to replace conventional hobbing process of gear.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.80-83
• /
• 1999

Rigid Plasticity Finite Element Analysis is developed for the shapes of dead metal zone and the curving velocity distribution in the eccentric square dies extrusion. The shape of dead metal zone is defined as the boundary surface with the maximum friction constant between the deformable zone and the rigid zone. The curving phenomenon in the eccentric square dies is caused by the eccentricity of square dies. The deviated velocity is changed with the distance form the center of cross-section of the workpiece. The results show that the curving of products and the shapes of the dead metal zone are determined by Rigid Plasticity Finite Element Analysis and that the curvature of the extruded products increases with the eccentricity.

• Journal of Sericultural and Entomological Science
• /
• v.27 no.2
• /
• pp.28-39
• /
• 1985

The structural and useful characteristics of silk habutae treated with silicone resin by emulsion finishing method were studied. The results were obtained through crease recovery test, water repellency test, scanning micrograph observation, amino acid analysis, X-Ray diffraction analysis, and Fourier Transform Infrared Spectroscopy. The results are summarized as follows; 1) The improvement in crease recovery of silk habutae finished with silicone resin, was observed b soaping treatment and curing conditions. 2) The higher water repellency and stiffness in silk fabrics finished with silicone resin was found by the fabric inspection and the scanning electron microscopic observation. It is suggested that silicone resin impregnated into the void of silk fibroin. 3) The polar side chains of amino acid composition were decreased, when the silicone resin was treated on silk fibroin. 4) Through Amino acid analysis of silicone resin finished fibroin, the different amounts of amino acid composition was indicated due to silk fibroin silicone polymer reaction and the structural difference of its fibroin were also proved by X-ray diffractograms. 5) The functionality of the siloxane compound may be deduced from the silicone finished silk habutae by Fourier Transform Spectroscopy. It was concluded from the above results that the useful characteristics of silk fabric can be improved by silicone resin finishing.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.80-86
• /
• 2024

This study was conducted to evaluate the potential of rape stalk (RAS) as a raw material for the production of solid bio-fuels. RAS was immersed in an aqueous solution with acetic acid concentration of 1 percent, The content of reducing sugars separated from the RAS was analyzed. Glucose showed the highest content followed by xylose, galactose, arabinose and mannose. The immersed and non-immersed RAS were used for producing pellets with a pilot-scaled flat-die pellet mill. Bulk density and calorific values of the pellets improved with the use of the immersed RAS and the addition of wood particles. The values exceeded the minimum requirements for the A-grade of non-woody pellets (≧600 kg/m³ & ≧ 14.5 MJ/kg) designated by the ISO. Ash content of the pellets reduced with the immersion of RAS and the value satisfied the A-grade level (≦6.0%) of the ISO standard. The durability of the immersed RAS-based pellets was much higher than that of non-immersed IRS-based pellets, and the values were increased with the addition of wood particles. However, the durability did not meet the acceptance level for the B-grade of non-woody pellets (≧96.0%) designated by the ISO. These results suggested that the addition of binders in the production of non-woody pellets using an RAS immersed in acetic acid-based aqueous solution is required for the commercialization of the pellets.

• Transactions of Materials Processing
• /
• v.4 no.2
• /
• pp.141-150
• /
• 1995

The purpose of the open die press forging is to maximize the internal deformation for better structural homogeneity and center-line consolidation in case of the ingot. A two and three dimensional viscoplastic finite element analysis is carried out for the plate, cylinder and square forging with the flat die in order to study the forging effects during the process. Effect of width, height reduction, and die staggering are studied through simulation of the process. Thus favorable working conditions are suggested for better and more disirable product quality.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.437-440
• /
• 2000

Composite material consists of more than two materials and make various kinds of composite materials by combining different single materials. Copper clad aluminum composite material is composed of Al and Cu, and it has already been put to practical use in Europe because of its economic benefits. This paper presents the interface bonding according to the variation of extrusion ratio and semi-angle die by observing the interface between Cu and Al using metal microscope. By that result, we can predict the conditions of the interface bonding according to the extruding conditions.