• Proceedings of the Korean Information Science Society Conference
• /
• 2002.10d
• /
• pp.502-504
• /
• 2002

군중잡음(crowd noise)이 발생하는 환경에서 음성 통화 및 화자 인식을 할 때에는 음성에 파열음이나 마찰음과 같은 유색잡음(colored noise)이 부가되어 원래 음성이 왜곡된다. 이와 같이 왜곡된 음성 신호를 처리할 때에는 군중잡음을 제거하는 과정이 반드시 필요하다. 본 논문에서는 군중잡음의 특성을 분석하고, 그 결과를 이용하여 음성 신호처리 시에 효과적으로 군중잡음만을 제거할 수 있는 모델을 제안한다. 제안된 모델은 시간 영역에서는 침묵 구간을 검출하여 마찰음과 파열음을 제거하는 과정과 주파수 영역에서는 잡음 평균을 생성하고 이를 이용한 스펙트럼 차감법(spectral subtraction)으로 군중 잡음을 제거하는 과정으로 이루어진다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.4
• /
• pp.83-93
• /
• 1983

A non-linear numerical tidal model of the Yellow Sea and the East China Sea is used to derive the mean and maximum bed stress the mean and maximum transport potential on the continental shelf. It has provided a preliminary assessment of relation between sediment transport paths and the mean and maximum bed stress distribution determined from the numerical model.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.5
• /
• pp.461-467
• /
• 2012

An experimental study was carried out to measure frictional pressure drop in flow boiling to deionized water in a microchannel having a hydraulic diameter of $500{\mu}m$. Tests were performed in the ranges of heat fluxes from 100 to $400kW/m^2$, vapor qualities from 0 to 0.2 and mass fluxes of 200, 400 and $600kg/m^2s$. The frictional pressure drop during flow boiling is predicted by using two models; the homogeneous model that assumes equal phase velocity and the separate flow model that allows a slip velocity between two phases. From the experimental results, it is found that the two phase multiplier decreases with an increase in mass flux. Measured data of pressure drop are compared to a few available correlations proposed for macroscale and mini/microscale. The homogeneous model well predicted frictional pressure drop within MAE of 29.4 % for the test conditions considered in this work.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.3075-3083
• /
• 1994

The applications of the electrical transmission line theory to the pressure propagation characteristics in the volume loaded fluid transmission line with step and impulse input wave is demonstrated in this paper. The method is based on the premise that the time response is the inverse Fourier transform of frequency spectrum of the wave which spectrum is a product of frequency spectrum of input pressure wave and system transfer function. The frequency response and transient response of step and impulse input wave in the volume loaded fluid transmission line is analysed by the Laplace transform and inverse Laplace transform with FFT numerical algorithm. The numerical solution of the distributed friction model is compared with the average friction model and the infinite product model. And the result is showed that FFT method may have major advantages for the simulation of fluid circuitary.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1281-1293
• /
• 2013

A sophisticated finite element model is illustrated to analyze the behavior of Prefabricated Parallel Wire Strand(PPWS) sockets for main cables of suspension bridges. An orthotropic model is proposed for the casting material by considering both effects of individual wires and a casting alloy, and the contact between surfaces of a socket and a casting alloy is idealized by using the Coulomb friction and the surface-based contact model. The proposed FE model is verified by comparing the strain distributions obtained from the tensile test and FE analysis. The mechanical behavior of a socket is investigated with respect to the variation of the frictional coefficient. The result shows that the friction between surfaces significantly diminishes the stress concentration of a socket and a casting alloy, and the normal stress from the design equation represents the averaged value of the upper and lower quartiles in the distribution of contact stresses between a socket and a casting alloy.

• Journal of the Korea Concrete Institute
• /
• v.28 no.2
• /
• pp.167-176
• /
• 2016

Shear friction strength model of concrete was proposed to explain the direct friction mechanism at the concrete interfaces intersecting two structural elements. The model was derived from a mechanism analysis based on the upper-bound theorem of concrete plasticity considering the effect of transverse reinforcement and applied axial loads on the shear strength at concrete interfaces. Concrete was modelled as a rigid-perfectly plastic material obeying modified Coulomb failure criteria. To allow the influence of concrete type and maximum aggregate size on the effectiveness strength of concrete, the stress-strain models proposed by Yang et al. and Hordijk were employed in compression and tension, respectively. From the conversion of these stress-strain models into rigidly perfect materials, the effectiveness factor for compression, ratio of effective tensile strength to compressive strength and angle of concrete friction were then mathematically generalized. The proposed shear friction strength model was compared with 91 push-off specimens compiled from the available literature. Unlike the existing equations or code equations, the proposed model possessed an application of diversity against various parameters. As a result, the mean and standard deviation of the ratios between experiments and predictions using the present model are 0.95 and 0.15, respectively, indicating a better accuracy and less variation than the other equations, regardless of concrete type, the amount of transverse reinforcement, and the magnitude of applied axial stresses.

• Journal of the Korea Concrete Institute
• /
• v.28 no.4
• /
• pp.419-426
• /
• 2016

This study examined the effect of transverse reinforcement and compressive stress on the shear friction performance at the shear interface intersecting two structural elements with various concrete types. From the prepared 12 push-off test specimens, various characteristics at the interface were measured as follows: crack propagation, shear load-relative slip relationship, initial shear cracking strength, ultimate shear friction strength, and shear transfer capacity of transverse reinforcement. The configuration of transverse reinforcement and compressive strength of concrete insignificantly influenced the amount of relative slippage at the shear friction plane. With the increase of applied compressive stress, the shear friction capacity of concrete tended to increase proportionally, whereas the shear transfer capacity of transverse reinforcement decreased, which was insignificantly affected by the configuration type of transverse reinforcement. The empirical equations of AASHTO-LRFD and Mattock underestimate the shear friction strength of concrete, whereas Hwang and Yang model provides better reliability, indicating that the mean and standard deviation of the ratios between measured shear strengths and predictions are 1.02 and 0.23, respectively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.3
• /
• pp.170-177
• /
• 1981

1,200.deg.C에서의 단조철은 점소성을 나타내며 인발과 압출시 변형영역이 구형수렴형태가 됨을 실험을 통하여 나타난다. 이 변형역 모델로부터 평형방정식을 사용하여 평균 압출 및 인발응력과 정수압을 계산해 낸다. 평균 압출 및 임발응력은 상계 해석 방법에 의한 결과와 비교하여 본 연구의 해석방법의 유효성을 타진하고 정수압은 다른 연구자들의 결과와 비교 검토되며 특히 냉간가공의 경우와 비교 검토 된다. 그 외에 마찰계수, 급형각도와 단면감소율의 영향에 대해서도 논의 된다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.124-124
• /
• 2017

Fe-Ni-Co 합금 박막(<$100{\mu}m$)을 황화물계 용액에서 전주공정으로 제조하였다. XRF로 측정한 박판의 평균 조성은 Fe-34 wt.% Ni-3 wt.% Co 이다. AFM으로 측정한 표면 조도는 35.2 nm 이다. 표면의 나노 경도는 평균 5.4 GPa 이었다. Oliver 모델을 적용한 구리 박막의 탄성하강강성도는 약 75 이었다. Alekhin 모델을 적용한 구리 박막의 마찰계수, 피로한계는 각각 0.134, 0.027 이었다. 유한요소법으로 평가한 Berkovich 형 나노압침선단의 하중분포를 이차원 선형 및 비선형 해석하면 1 [mN]의 정적하중을 가한 Fe-Ni-Co 박막은 약 576 [mN]로 예측되었다. 압침선단의 하중집중정도는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.1
• /
• pp.52-60
• /
• 2008

Staggered dimples printed on opposite walls of an internal cooling channel are formulated numerically and optimized to enhance heat transfer performance. Nusselt number and friction factor based objectives are considered and a weighted average surrogate model is used to approximate the data generated by numerical simulation. The dimpled channel shape is defined by three geometric design variables, and the design point within design space are selected using Latin hypercube sampling. A weighted-sum method for multi-objective optimization is applied to integrate multiple objectives into a single objective. By the optimization, the objective function value is improved largely and heat transfer rate is increase much higher than pressure loss increase due to shape deformation. Channel with vertically non-symmetric optimum dimples is tested and found that the best appears if dimples on opposite wall are displaced by one quarter of dimple spacing.