• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.192-201
• /
• 2003

In this paper, to reduce the size of patch, three types of 3-dimensional patch antennas which are one-directionally-corrugaged type, rectangular ring-likely corrugated type, and lattice-likely corrugated type rectangular microstrip patch antennas(MPA) are designed and fabricated at the 1.575 GHz. As the result, one-directionally corrugated rectangular MPA is reduced in the resonant length of patch by 21.4% than that of general plane MPA. -10 dB bandwidth(B.W) is 62 MHz(3.9 %) and this is broader than that(39 MHz, 2.5 %) of plane MPA by 23 MHz(1.5 %). The gain is 5.8 dBd and this is reduced by 0.9 dB than that(6.7 dBd) of plane MPA. Half power beamwidth(HPBW) is broadened by 18$^{\circ}$ than that of plane MPA in the E-plane and this is due to the reduced length of patch. For rectangular ring-likely corrugated retangular MPA, the patch size is miniaturized by 21.6 % than that of plane MPA. For lattice-likely corrugated rectangular MPA, in the linear polarization, the size of patch is miniaturized by 43.3 % than that of plane MPA. -10 dB B.W is 70 MHz(4.4 %) and this is broadened than that of plane MPA by 31 MHz(2 %). Gain is 2.2 dBd and this is smaller than that of plane MPA by 4.5 dB. HPBW is increased in both E-plane and H-plane by 22$^{\circ}$ and 13$^{\circ}$, respectively. For circular polarization, the size of patch is reduced by 41 % than that by 41 %. The axial ratio(AR) is 0.8 dB at the 1.575 GHz and the axial ratio bandwidth(ARBW) within 2 dB is 20 MHz(1.27 %) and this is increased by 10 MHz(0.63 %) than that 10 MHz(0.63 %) of plane MPA. From all the results above, it is conformed that the proposed antenna has merit in size reduction of patch and in the input impedance B.W, and is more profitable in many application than the general plane type MPA.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.9
• /
• pp.817-825
• /
• 2013

The UHDTV system, which provides realistic service with ultra-high definite video and multi-channel audio, has been studied as a next generation broadcasting service. Since the conventional digital terrestrial transmission system is not capable to cover the increased transmission data rate of the UHDTV service, there are great necessity of researches about increase of data rate. Accordingly, the researches has been studied to increase the transmission data rate of the DVB-T2 system using dual-polarized MIMO technique and high order modulation. In order to optimize the MIMO DVB-T2 system where irregular LDPC codes are used, it is necessary to study the design of the bit mapper that matches the LDPC code and QAM symbols in MIMO channel. However, the research related to the design of the bit mapper has been limited to the SISO system. Therefore, this paper defines a new parameter that indicates the VND distribution of MIMO DVB-T2 system and performs the performance analysis according to the parameter which will be helpful for designing a MIMO bit mapper.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.2
• /
• pp.11-19
• /
• 1999

The design procedure as well as some test results of a low-cost commercial radome for mobile DBS(Direct Broadcasting Satellite) receiving antenna system are presented in this paper. At first the complex permittivity of dielectric material should be measured in order to select a material for radome design. The complex permittivities of low-cost plastics supplied by domestic vendors are measured and presented. And then the transmission losses of the sheets are calculated. The calculated results are verified by the measurements of wave transmission test of that sheets. Two kinds of radomes, ABS single-layer and A-Sandwich((PET-Foam-ABS), are fabricated and measured practically. The transmission losses of single-layer and A-sandwich radome are 1.5dB and 0.6dB respectively at the maximum wave incident angle of 57 degree. Also the calculated crosspolarization caused by A-sandwich radome is under 20dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.545-551
• /
• 2011

In this paper, we described a measurement method of an EIRP(Effective Isotropic Radiated Power) of a WCDMA base station using a pilot channel in line-of-sight environments. Especially we measured it in real base station environments in order to apply this method to domestic base station inspection test. Estimated EIRP results from measured value is -2 dB lower than theoretical values, which is calculated by the data of transmit antenna. The deviation of -2 dB is verified as a polarization mismatch between the base station antenna and a receiver antenna, and it can be calibrated. Therefore, we verified that our measurement method could be an effective tool to measure an EIRP in WCDMA base station inspection test.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.174-180
• /
• 2004

The World Radiocommunication Conference in year of 2000 adopted new Plans as well as Lists for BSS and its feeder-link in the Regions 1 and 3, based on the new technical criteria such as small size of antenna and low satellite power. Since the new Plans and Lists were based on new technical criteria, ITU was requested to review the relevant regulatory procedures and sharing criteria of broadcasting satellite networks contained in Appendices 30 and 30A of Radio Regulations. Korean BSS network at 116$^{\circ}$E was chosen for the study and ITU S/W (MSPACEG) was used. We analyzed the interference effects from adjacent BSS networks to Korean BSS network using parameters of an antenna diameter and polarization of receiving earth station. The analysis shows that it is difficult to co-operate BSS networks both at 116$^{\circ}$E and 113$^{\circ}$E, however, it is possible to use small antenna (i.e. 45cm) in frequency sharing among BSS networks with 6$^{\circ}$ orbital separation.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.8
• /
• pp.45-53
• /
• 1999

Electromagnetic scattering by finite number of conducting strips loaded on a grounded dielectric is considered for the TM polarization case from the viewpoints of transmitting(receiving) leaky wave antenna and grating coupler. An integro-differential equation whose unknowns are the induced currents over the strips is derived and solved by use of the method of moments. In order to construct the non-uniform leaky wave structures with specific source(current) distributions over the strips, distances between two adjacent strips and strip width are simultaneously varied along the structure. From some results for the current distributions over the strips and surface wave powers, it is observed that the maximum coupling efficiencies of the appropriately constructed non-uniform leaky wave structures from the viewpoints of both a receiving leaky wave antenna and a grating coupler amount upto 95%, which are about 15% improvements compared with those(80%) of the uniform structures.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2058-2060
• /
• 2004

In this paper, circular polarized antennas of Tx 30GHz and Rx 20GHz are implemented in LTCC process. Tx antenna has a circular patch structure and Rx antenna has a ring patch structure. The feeding line of Tx antenna is placed in the center hole of Rx ring patch antenna which is printed under Tx circular patch antenna layer. It makes antenna size smaller. Tx antenna's return loss in under -10dB level from 30GHz to 31GHz and Rx antenna is under -10 dB from 20GHz to 21GHz. The isolation between two antennas is less than -20dB. Axial ratio is less than 3dB though out each band.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.3
• /
• pp.471-477
• /
• 2013

We have studied on the possibility of precise positioning using hybrid Track Circuit system. Hybrid Track Circuit uses RFID which replaces UHF. Hybrid Track Circuit is a part of next generation railroad signal system which is available to communicate with a railway on board system based on a realtime operating system. If applicate on a current hand operating subway, phenomenon caused by driver's mistake such as passing a stop without stopping or mismatch error between PSD and train door should be prevented.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.293-296
• /
• 2005

This paper presents the design of linear and circular polarization baseball- shaped circular microstrip antenna (BCMA) with 3-dimensional structure using perturbation effect to reduce its size, which runs at 1.575GHz frequency bandwidth. As a result, the size of linear polarized antenna could be reduced up to 23.7% in patch diameter and 41.8% in its area. Linear polarized antenna has -26.04dB of return loss, 69MHz(4.38%) of -l0dB bandwidth, 4.51dBd of gain, and its -3dB beamwidth are 99$^{\circ}$ in E-plane, 83$^{\circ}$ in H-plane. Circular polarized antenna has -17.43dB of return loss, 113.7MHz(7.2%) of -l0dB bandwidth, 2dBd of gain, 2dB of axial ratio and its -3dB beamwidth are 87$^{\circ}$, 86$^{\circ}$ x-axis polarized, 80$^{\circ}$, 84$^{\circ}$ y-axis polarized. It has 82mm of diameter, which is 28.5% of linear polarized CMPA. Therefore, in this paper we verified that baseball-shaped 3-dimensional structure of circular microstrip patch antenna applied with perturbation effect is appropriate for miniaturization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.426-435
• /
• 2002

In this paper we present an indoor propagation model for indoor wireless LAN service in the ISM band. We primarily use a 3D ray tracing as well as a patch scattering model in order to take into account the indoor fixtures. Therefore input parameters such as indoor environment parameters and antenna's types, polarizations are considered. As the results, we present fading characteristics and rms delay spread from time delay spread. In order to investigate the accuracy of the presented model, comparisons of predictions with measurement and simulations are performed in indoor wireless LAN service environments. The results show that measurements and simulations are very similar. Therefore in this paper, the effect of presented indoor propagation model is confirmed.