• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.469-471
• /
• 2008

The charge pump affects the performance of PLL. In designing the charge pump, we need to consider various issues such as current mismatch, charge sharing, feedthrough, charge injection, and leakage current. This paper propose the new charge pump circuit which is improved in terms of the current match over the existing high-speed charge pump. The simple method used for reducing current mismatch is the technique that uses a cascode in order to increase the output resistance of the charge pump. However the method limits the output voltage range of the charge pump. So the method is hard to apply as the supply voltage is lowered. Thus this paper proposes a new charge pump circuit using an op amp instead of the cascode. And the new charge pump circuit has an excellent current matching characteristics over a wide output range.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06a
• /
• pp.22-28
• /
• 1989

유압베인펌프는 토출유량이 많고 소형으로 동력밀도는 높으나 토출압력면에스는 피스톤식 펌프에 뒤지기 때문에 발생압력의 고압화에 대한 연구가 계속되어 왔다. 유압장치의 경제적인 압력으로서 $300kgf/cm^2$가 제시되어 있는 가운데, 유압베인펌프의 고압화의 연구가 진행중에 있는 점, 또한 최근들어 에너지 절약의 일환으로 펌프의 수명연장 문제가 거론되어 지고 있는 점, 물에 타기 어려운 난연성유압 작동유를 사용할 경우 마찰증대 및 마모성능이 저하하는 점 등의 이유에서 유압베인 펌프의 마찰, 윤활문제가 중요시 되어지고 있다. 특히 펌프의 체적효율을 높이는 것과 마찰, 마모를 저하시키는 것과는 서로 상반된 관계에 놓여있기 때문에 문제의 해결에 어려움을 갖고 있다. 이와같은 모순을 해결하기 위해서는 베인과 캠링사이의 슬라이딩부분의 윤활상태를 파악하지 않으면 안된다. 그러나 베인의 선단부에는 10-20ms의 짧은 시간동안에 수백기압의 압력이 변화하기 때문에 지금까지 확실한 작용력의 파악이 어려워 이 분야의 윤활상태 파악에 관한 연구는 거의 이루어지지 않고 있다. 베인과 캠링간의 윤활상태를 윤활공학적 관점에서 보면 변동하중 상태에서의 슬라이딩 탄성유체윤활상태 또는 혼합윤활상태에 있는 것으로 판단되어지는데, 이와같은 여러가지 어려운 조건 때문에 윤활상태를 파악하는데, 어려운점이 뒤따르게 된다. 위와 같은 배경에 착안하여 본 연구에서는 유압베인펌프를 모델화하여 변동하중상태에서 실험이 가능한 장치를 제작, 사용하여 베인 선단 슬라이딩부분의 윤활상태를 파악하였다.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.5
• /
• pp.67-76
• /
• 2011

생활공간 냉난방용 열펌프의 성능향상을 위해 R22의 대체 냉매로서 새로운 혼합냉매R22/R23/R152a(RM-1)을 개발하고 U. S. A.의 NIST사의 REFPRO Pprogram을 이용해 이 혼합냉매의 P-h diagram을 구성하여 실용화에 이용할 수 있도록 하였다. 본 연구는 실험을 통해 R22와 RM-1의 열펌프 성능효과를 분석하였다. 입 출구 물의 온도와 제2의 전열매체로서 물의 질량유량, 압축기의 소요 에너지 그리고 열펌프의 기타 열적 특성을 다양한 조건하에서 측정하였다. 이 실험 데이터를 통해 공기-물 열펌프 시스템에서의 RM-1과 R22의 성능계수(COP)를 비교하였다. 이를 통해, 혼합냉매 RM-1을 사용하는 열펌프 시스템은 외기온 $-17^{\circ}C$에서도 2.2의 성능계수로 작동하는 결과를 본 연구에서 보여주었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1572-1583
• /
• 1993

This paper deals with the analysis method of regenerator characteristics for designing a vuilleumier heat pump. First, models for evaluating the reheat and the flow losses are established by the comparative study between already proposed ones. Calculations based on the second-order method are performed for the well-known schulz heat pump. Results show that operating conditions as well as design parameters significantly affect the regenerator performances. The effects of operating conditions on the reheat and the flow losses appear to be similar in trends in both the hot-warm and the cold-warm regenerators. However, the losses in the one regenerator vary oppositely to those in the other with specific design parameters such as the phase angle and the swept volume ratio being changed. Also, it is confirmed that there is an optimum aspect ratio(D/L) which minimizes total loss for each regenerator.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.3
• /
• pp.20-26
• /
• 2009

Turbopump test for a 30-ton-thrust liquid rocket engine was carried out using real-propellant. Liquid oxygen, kerosene, cold hydrogen gas were used for the oxidizer pump, the fuel pump, and the turbine, respectively. The turbopump was reliably operated at the design and off-design conditions and the performance requirements were satisfied, which implies that the turbopump development at the engine subsystem level is successfully accomplished in the point of performance validation. This paper presents the results of a test where the turbopump was run for 75 seconds at three operating modes. In terms of performance characteristics of pumps and turbine, the results of turbopump assembly test using real-propellant showed a good agreement with those of the turbopump component tests using simulant working fluid.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.11-17
• /
• 2009

Hot-fire test of a turbopump for a gas generator cycle rocket engine of 30 ton class was carried out in real propellant environment. Liquid oxygen and kerosene were used for the oxidizer pump and the fuel pump, respectively, while hot gas produced by the gas generator was supplied to the turbine. A part of the propellant discharged from the pumps was provided to the gas generator. The turbopump was run stably at both on-design and off-design conditions, satisfying all the performance requirements. This paper describes one of the test cases, where the turbopump was run for 120 seconds at three different operating modes in one test. In terms of performance characteristics of pumps and turbine, the results from turbopump assembly test using real propellant showed a good agreement with those from the turbopump component tests using simulant working fluid.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.359-365
• /
• 2008

Turbopump test for a 30-ton-thrust liquid rocket engine was carried out using real-propellant. Liquid oxygen, kerosene, cold hydrogen gas were used for the oxidizer pump, the fuel pump, the turbine, respectively. The turbopump was run stably at the design and off-design conditions and the performance requirements were satisfied, which implies that the turbopump development at the engine subsystem level is successfully accomplished in the point of performance validation. This paper presents the results of a test where the turbopump was run for 75 seconds at three operating modes. In terms of performance characteristics of pumps and turbine, the results from turbopump assembly test using real-propellant showed a good agreement with those from the turbopump component tests using simulant working fluid.

• Proceedings of the KIEE Conference
• /
• 2005.07d
• /
• pp.2622-2624
• /
• 2005

화력발전소 보일러의 급수량은 유출되는 증기량에 맞추어 자동 조절된다. 유출 증기량이 변하는 상황에서도 이에 상응하는 급수량은 실시간으로 조절되어야 한다. 증기량과 급수량에 차이가 있으면 보일러의 보유 수량과 드럼의 수위가 변하게 되므로, '드림수위를 일정하게 유지하는 것'이 급수량제어의 목표라고 할 수 있다. 본 논문은 실제 운용되고 있는 설비를 대상으로 고찰한 내용이며, 급수펌프 구동력으로는 중기터빈을 사용한다. 증기터빈과 급수펌프는 같은 축으로 연결되어있으며, 급수량 조절은 급수펌프의 회전속도를 제어함으로써 이루어진다. 터빈에 사응되는 증기는, 고압과 저압 2종류이며, 저압 증기가 부족한 경우에 고압증기를 사용하는 구성으로 되어있다. 증기 밸브의 유량 특성에는 비선형성을 많이 포함하고 있었다. 이 외에도 급수펌프가 갖는 비선형성을 분석하였으며, 이 특성들을 모두 종합한 '증기터빈 속도제어기 튜닝 곡선'을 제시하였다

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.7-10
• /
• 2009

The development and evaluation of solid propellant were performed for the turbopump pyro starter, which start up the liquid propellant rocket engine for the Space Launch Vehicle (SLV). Requirements for the turbopump pyro starter propellant include the production of low flame temperature, low burning rate and nontoxic gas to protect the mechanical corrosion or air pollution. This study describes the development of the solid propellant composition which is based on PCP binder. DHG (Dihydroxy glyoxime), which has advantages of oxygen balance and ignition, was used as coolant. The mechanical properties and burning rate of the propellants were measured. Finally, static fired test was performed to prove the possibility of development.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5587-5594
• /
• 2012

Determination of the soil-water characteristic curve is one of the most important things to solve geotechnical engineering problems. Expecially, convenient and reliable method to measure the soil-water characteristic curve during drying and wetting cycles is required with lower labor input, more independence from operator experience, and shorter testing time than other available methods. Many measurement methods including the flow pump system have been developed to characterize the soil-water characteristic curve for the several decades. This study measured the soil-water characteristic curve during drying and wetting cycles using a suction control technique with the flow pump system. Two test materials were used for determination of the soil-water characteristic curve, and it is concluded that suction control technique is suitable for determination of the soil-water characteristic curve and characterization of the hydraulic hysteresis with varying test conditions. Especially, the suction control technique can reduce error of measurement and save time in measuring the soil-water characteristic curve due to automated system and high degree of precision.