• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.10
• /
• pp.1049-1056
• /
• 2014

Microelectronics components contain various materials with different coefficients of thermal expansion (CTE). Although a large amount of published data on the CTE of standard materials is available, it occasionally becomes necessary to measure this property for a specific actual material over a particular temperature range. A change in the temperature of a material causes a corresponding change in the output of the strain gage installed on the specimen because of not only the mechanical load but also the temperature change. In this paper, a detailed technique for CTE measurement based on these thermal characteristics of strain gages is proposed and its reliability is evaluated. A steel specimen, aluminum specimen, and copper specimen, whose CTE values are well known, were used in this evaluation. The proposed technique was successfully applied to the measurement of the CTE of a coreless package substrate composing of electronics packages.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.1
• /
• pp.157-162
• /
• 2018

The partial molar volumes of an antidepressant in Halobacteriun Halobium and in suspensions of several lipids have been determined at $25^{\circ}C$ it using a excess volume dilatometer. The potency of general antidepressant, Fluoxetine has long been known to correlate with lipid solubility. Denaturations of the vesicle, which is a sole membrane protein in the purple membrane of Halobacteriun Halobium, were studied by absorption changes at 280 nm and fluorescence changes at 330 nm with excess volume dilatometer. The 1H NMR analysis of viscous polymer solutions by diffusion interchange is the important step by measurement. The partial molar volume and particle size of Fluoxetine in Halobacteriun Halobium were measured to be positive. An antidepressant can prevent diseases that produce a variety of cognitive and mental symptoms based on low morale and depression, resulting in poor daily performance.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.2 s.39
• /
• pp.1-7
• /
• 2006

In this paper, warpage magnitude and shape of printed-circuit board in case that properties of core and thickness of solder resist are varied are investigated. The cause of warpage is coefficient of thermal expansion differences of stacked materials. Therefore, we need small difference of coefficient of thermal expansion that laminated material, and need to decrease asymmetric of top side and bottom side in structure shape. Also, we can control occurrence of warpage heightening hardness of core in laminated material. Composite material that make core are exploited in connection with the structural bending twisting coupling resulting from directional properties of fiber reinforced composite materials and from ply stacking sequence. If we use such characteristic, we can control warpage with change of material properties. In this paper, warpage of two layer stacked chip scale package is investigated, and evaluate improvement result using an experiment and finite element method tool.

• Journal of the Korean Ceramic Society
• /
• v.38 no.2
• /
• pp.158-165
• /
• 2001

고체산화물 연료전지용 밀봉재로서 전지 구성원과 열팽창계수가 유사하고 비젖음성 특성을 가지며 전지 작동온도에서 화학적 안정성을 갖는 밀봉유리를 개발하고자, BaO-Al$_2$O$_3$-La$_2$O$_3$-Ba$_2$O$_3$-SiO$_2$계 유리를 제조하여 조성 변화에 따른 열적 특성 변화와 접합후의 젖음성 및 반응성 등을 조사하였다. 유리망목 형성산화물인 B$_2$O$_3$와 SiO$_2$의 함량비 및 BaO의 망목 형성산화물(B$_2$O$_3$+SiO$_2$)에 대한 함량비 변화에 따른 유리의 열적 특성을 조사한 결과, 0.33~0.71의 B$_2$O$_3$/SiO$_2$함량비하에서 BaO/(B$_2$O$_3$+SiO$_2$)가 0.70일 때 유리의 열팽창계수는 106~111$\times$$10^{-7}$/K 이었으며 이때 연료전지 구성원인 YSZ(yttria stabilized zirconia)와의 열팽창 불일치(thermal expansion mismatch)가 가장 작았다. 또한 이러한 조성의 유리로부터 분말성형체를 제조하여 YSZ에 접합을 시도한 결과, 우수한 접합성 및 비젖음성을 확인할 수 있었으며, 800~8$50^{\circ}C$의 전지 작동온도에서 100시간까지 유지시에도 YSZ와의 계면반응이 일어나지 않음을 관찰할 수 있었다.

• Composites Research
• /
• v.16 no.2
• /
• pp.41-47
• /
• 2003

This paper is concerned with the performance evaluation and comparison analysis fur several kinds of LIPCA (Lightweight Piezo-Composite Actuator) device system. LIPCA device system is composed of a piezoelectric ceramic layer and fiber reinforced light composite layers, typically a PZT ceramic layer was sandwiched by a top fiber layer with low CTE (coefficient of thermal expansion) and base layers with high CTE. To investigate the effect of lay-up structure of the LIPCA on the actuating performance, four kinds of actuator with different lay-up stacking sequence were designed, manufactured, and tested. The performance of each actuator was evaluated using an actuator test system consisted of an actuator supporting jig, a high voltage actuating power supplier, and a non-contact laser measuring system. From the comparison of the performance of the LIPCA prototypes, it was found that the actuator with higher coefficient of unimorph actuator can generate larger actuating displacement.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.94-100
• /
• 2002

This paper is concerned with the development, and performance test of LIPCA (Lightweight Piezo-composite Curved Actuator) that is lighter than other conventional piezo-composite type actuators. LIPCA is composed of top fiber composite layers with a high modulus and low CTE (Coefficient of Thermal Expansion), a middle PZT cermaic wafer, and base layers with a high modulus and high CTE. The performance of each actuator was evaluated using an actuator test system consisting of an actuator supporting jig, a high voltage actuating power supplier, and a non-contact laser measuring system. The simply supported condition actuator was excited by the power supplier with 1.0Hz cycle and up to $100\sim400V_{pp}$. The displacement at the center point of actuator was measured with non-contact laser displacement measuring system, It has been shown that the LIPCA-C2 can 34% decrease in mass and 13% increase in displacement compared to THUNDER.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.176-184
• /
• 1993

The glasses, which the $\beta$-spodumene as the principal crystalline phase could be precipitated, were melted by adding >, $P_2O_5, TiO_2, ZrO_2 in the Li_2O-Al_2O_3-SiO_2$ system. In order to achieve the glass-ceramic body of near-theoritical density by sintering method, the optimum condition of heat treatment, the effect of glass powder size and the properties were investigated by DTA, XRD, bulk density, thermal expansion and SEM. Addition of $P_20_5$ imProved the tendency of sintering and the sample with 9wt% $P_20_5$ content was the most dense OOdy by sintering method. The optimum condition of heat treatmemt was sintered for densitification at $740^{\circ}C$ and crystallized at $950^{\circ}C$. In the optimum condition, the relative density was above 90% and the thermal expansion was negative about $-1{\times}10^{-7}/^{\circ}C$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.195-195
• /
• 2003

PDP, FED 등의 디스플레이와 각종 IC 칩부품에 적용 가능한 저융점 유리 프릿 중에서 환경규제가 이루어지고 있는 납성분이 포함되어 있지 않은, Bi계 유리 프릿의 열적 거동 연구를 행하였다. 열처리 온도에 따른 열거동에 따라 프릿의 소성온도 및 미세구조가 결정되므로, 열처리 온도에 따른 유리 프릿의 젖음각을 측정하였고, DTA와 TMA를 통해 유리전이온도, 연화점, 열팽창계수 변화 경향성을 관찰하였다. 본 연구에서 제조된 유리는 조성에 따라 전이온도가 390-50$0^{\circ}C$, 연화점이 400-55$0^{\circ}C$, 열팽창계수가 65-120$\times$10-7/$^{\circ}C$ 범위를 나타내었으며, 고온현미경 측정 결과 Pb-계 유리와 비교시 유사한 열거동을 나타내었다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.323-324
• /
• 2010

The purpose of this study was to investigate alkali-silica reaction of accelerating agents in shotcrete. The test was performed with accelerating agents (aluminate, alkali-free, cement based mineral admixture) in the Type I cement. As a test result, using the nonreactive aggregates, detrimental expansion due to alkali-silica reaction doesn't occurred regardless of equivalent alkali contents of accelerating agent.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.195-198
• /
• 2000

It can be acquired the high effective productivity through of high speed, precision of machine tools, and then, machine tools will be got a competitive power. Industrially advanced countries already developed that the high speed feed is 60m/min using the high speed ball screw. Also, a lot of problems have happened the feed drive system. It is necessary to study about the characteristics of thermal deformation played a more critical role than static stiffness and dynamic rigidity in controlling the level of machining accuracy. In spite of the improving the thermal deformation characteristics of machine tools at the design stage, there are always some residual errors that have to be compensated for during machining. In this study, thermal deformation error automated compensation device with multiple linear regression is proposed that thermal deformation error can be eliminated at the machining stage. The developed device has been practically applied to the feed drive unit.