• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.414-420
• /
• 2012

In an effort to commercialization of energy saving aeration apparatus, panel-type aeration membranes were prepared from polyurethane sheet of J company in Korea having tensile strength higher than $400kg_f/cm^2$ with thickness of 0.5mm. Micropores of 100 m size were made by poring technique utilizing needles. From lab-tests in 450 L water tank at temperature of $20^{\circ}C$, the performance of aeration panels at 40 L/min aeration rate showed 5 mg/L DO in less than 3 minutes approaching saturation point of 8 mg/L within 8 minutes. The results show very high efficiency with $K_{La(15)}$ ($16.34hr^{-1}$), Standard oxygen transfer efficiency (SOTE 54.7%) and Standard aeration efficienct (SAE 7.88 kg/kwh). Other pilot scale test in a $2m^3$ water tank with water temperature ($19^{\circ}C$) and aeration rate (30 L/min) showed DO exceeding 5 mg/L within 8 minutes along with $K_{La(15)}$ ($5.8hr^{-1}$), SOTE (42.1%) and SAE (6.41 kg/kwh). These efficiencies represent 2~2.5 times higher than conventional aeration devices. Especially, the achievement of higher Oxygen Transfer Rate indicate higher commercial viability. Conventional aeration devices when applied to clean water and wastewater frequently cause problems due to differences in actual Oxygen Transfer Rate. Our actual tests with $40^{\circ}C$ animal farm wastewater resulted very high efficiencies with Oxygen transfer efficiency ($OTE_f$ 22.1%) and $OTE_{pw40}$ (39.6%).

• Membrane Journal
• /
• v.6 no.4
• /
• pp.219-226
• /
• 1996

Rotary disc ultrafiltration module(RDM) was developed for the separation of oil emulsions. This module was devised to reduce the gel polarization phenomenon by alecoupling the operation pressure and the surface velocity of solution in ultrafiltration(UF) processes. Two-shaft engaged disc type RDM having 20 rotary disc membcanes(UOP, USA) was operated under 85kPa vacuum at $25^{\circ}$C. The pressure drop due to slip flow in the two-shaft RDM was found to be proportional to $(2.5{\omega}r)^{2}$. The pure water flux of two-shaft RDM decreased by 9.95% at the angular velocity of 41.89rad/s compared to the decrease of 3.01% for one-shaft RDM at the same velocity. When the angular velocity was changed from 31.42rad/s to 2.62rad/s, the flux decline for 1% cutting oil in two-shaft RDM was 30.16% that is similar to that of one-shaft RDM. Disc gap of 3mm and 7mm did not show any significant differences in the flux for 1% cutting oil solution. A modified model for two-shaft RDM showed good agreement with the experimental results for the cutting oil solution.

• Membrane Journal
• /
• v.23 no.5
• /
• pp.367-374
• /
• 2013

In the present study, Pebax-2533 plate membranes were prepared by drying precursor solutions which were obtained by dissolving Pebax-2533 polymer in 1-Propanol/n-Butanol mixed solvents. And then the $CO_2$ and $N_2$ permeation behaviors were tested by using a time-lag system. The prepared Pebax-2533 plate membranes showed a considerable $CO_2/N_2$ separation performance : the $CO_2$ permeability was 130 to 288 barr, and the $CO_2/N_2$ permselectivity was 5-8. The $CO_2$ permeation data obtained by varying feed pressure, permeation temperature, and solvent composition announced that not only the $CO_2$ sorption but also the $CO_2$ diffusion is equally important in the overall $CO_2$ permeation.

• Membrane Journal
• /
• v.6 no.2
• /
• pp.86-95
• /
• 1996

Rotary disc ultrafiltration module(RDM) was developed for the separation of oil e$$\mu$sions. This module was devised to reduce the gel polarization phenomenon by decoupling the operation pressure and the surface velocity of solution in ultrafiltration(UF) processes. The rotary disc membrane consists of 3mm-thick ABS plate covered with UF membrane (UOP, U.S.A.). When the angular velocity($\omega$) was increased, the pure water flux was slightly decreased due to pressure drop caused by centrifugal force and slip flow at the surface of membrane. The pressure drop was proportional to the square of linear velocity(${\omega}r$). When the angular velocity was changed from 52.36rad/s to 2.62rad/s, the flux decline for 5% cutting oil in one-shaft RDM at $25^{\circ}C$ and 0.1MPa was 30.16%. In the lower concentrations, angular velocity tends to give less effect on the flux. Flux(J; $kg/m^{2} \cdot s$) in a rotating disc module is mainly a function of the bulk concentration($C_{B}$; %), the linear velocity(${\omega}r$; m/s) and the effective transmembrane pressure($\Delta P_{T}$ ; Pa). Using a modified resistance-in-series model, the flux data of cutting oil experiments were fitted to give the following equation.