• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.11A
• /
• pp.933-940
• /
• 2011

In this paper, Ka-band transceiver for road watch radar system is designed and fabricated. The transceiver for road watch radar system is composed of waveform generator, frequency generator. IF transceiver and RF up/down converter. The transceiver especially has 3 different waveform mode for target detection range. The transceiver had over 150 MHz bandwidth in Ka-band and 22 dBm output power. The receiver gain and noise figure was 30 dB and 4 dB respectively. The receive dynamic range was 65.28dB and amplitude imbalance and phase imbalance of I/Q channel was 0.3 dB and 1.8 degree respectively. The transceiver meets the required electrical performances through the individual tests.

• Journal of Korea Multimedia Society
• /
• v.17 no.1
• /
• pp.34-42
• /
• 2014

In this paper an embedding algorithm based on commute time is implemented by organizing patches according to the graph-based metric, and its performance is analyzed by comparing with the results of principal component analysis embedding. It is usual that the dimensionality reduction be done within some acceptable approximation error. However this paper shows the proposed manifold embedding method generates the intrinsic geometry corresponding to the signal despite severe approximation error, so that it can be applied to the areas such as pattern classification or machine learning.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.5
• /
• pp.64-71
• /
• 2006

We developed a fiber-optic temperature sensor system, with 10 fiber Bragg gratings, for abnormal high-temperature monitoring in power systems. We used Gaussian line-fitting algorithm to compensate the spectrum distortion in the wavelength-scanned Farby-Perot filter demodulation scheme. Compared with highest-peak-detection method, the proposed algorithm substantially reduced measurement errors. The overall measurement error was less than 1[%] compared with the reference thermocouple and the linearity error was 0.37[%].

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.4
• /
• pp.81-89
• /
• 2009

The seepage should be analyzed to design or reinforce the levees. The steady seepage analysis is an usual application in USA and European countries where the large scaled dams and levees are existed. However, Korea and Japan, where the reaching time is short, the excessive forces are applied on the levees at the short reaching time if the seepages are analyzed in steady condition. Accordingly, the unsteady analysis based on the variation of time is necessitated. In the unsteady analysis, the flood wave type is necessary. No criteria and standards, however, are derived for the unsteady seepage in Korea. In the study, the flood wave type is derived for the unsteady seepage. The major reliable flood surface data are collected in 5 stations including Jindong of the Nakdong river basin. The data are sorted in duration, and they are non-dimensionalized. The statistical method is also applied to derive the waves. To verify the study, the seepage is analyzed by the derived wave and applied to the prototype. The results are also compared with the Japanese Method. The errors between the hydraulic gradient and critical velocity method are $0{\sim}0.7%$, $0{\sim}0.7%$ at the Jindong, $1.6{\sim}4.0%$, $1.7{\sim}4.1%$ at the Hyunpoong, $0.6{\sim}3.6%$, $0.6{\sim}3.7%$ at the Waegwan, $2.0{\sim}8.1%$, $2.0{\sim}8.1%$ at the Nakdong, and $1.2{\sim}9.8%$, $1.3{\sim}9.9%$ at the Jeongam, respectively. The relationship($R^2$) between each method is relatively high as $0.983{\sim}0.999$. This means the results are more logical than the Japanese method, and the study is applicable to the design of hydraulic structures.

• Geophysics and Geophysical Exploration
• /
• v.1 no.1
• /
• pp.49-56
• /
• 1998

Seismic tomography has been widely used as high resolution subsurface imaging techniques in engineering applications. Although most of the techniques have been using travel time inversion, waveform method is being driven forward owing to the progress of computational environments. Although full-waveform inversion method has been known as the best method in terms of model resolving power without high-frequency restriction and weak scattering approximation, it has practical disadvantage that it is apt to get stuck in local minimum if the initial guess is far from the actual model and it consumes so much time to calculate. In this study, 2-D full-waveform inversion algorithm in acoustic medium is developed, which uses result of traveltime tomography as initial model. From the application on synthetic data, it is proved that this approach can efficiently reduce the problem of conventional approaches: our algorithm shows much faster convergence rate and improvement of model resolution. Result of application on physical modeling data also shows much improvement. It is expected that this algorithm can be applicable to real data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.558-565
• /
• 2013

In this paper, modeling and simulation for performance analysis of high resolution SAR system has been carried out in the time, frequency and numeric domain using ADS Ptolemy simulation tool of Agilent corporation. SAR system consists of antenna, controller and transceiver. Error parameters affecting SAR system performances have been defined, modeled and simulated such as phase noise of frequency synthesizer, amplitude and phase characteristic of TWTA, sampling frequency of waveform generator and I/Q imbalance. Finally, the development requirements of SAR system based on the impulse response function have been derived.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.2
• /
• pp.135-144
• /
• 2003

A method for the automatic segmentation of speech signals is described. The method is dedicated to the construction of a large database for a Text-To-Speech (TTS) synthesis system. The main issue of the work involves the refinement of an initial estimation of phone boundaries which are provided by an alignment, based on a Hidden Market Model(HMM). Multi-layer perceptron (MLP) was used as a phone boundary detector. To increase the performance of segmentation, a technique which individually trains an MLP according to phonetic transition is proposed. The optimum partitioning of the entire phonetic transition space is constructed from the standpoint of minimizing the overall deviation from hand labelling positions. With single speaker stimuli, the experimental results showed that more than 95% of all phone boundaries have a boundary deviation from the reference position smaller than 20 ms, and the refinement of the boundaries reduces the root mean square error by about 25%.

• Journal of Convergence for Information Technology
• /
• v.11 no.8
• /
• pp.1-7
• /
• 2021

In this paper, a method of extending 1 bit by adding an external device to a parallel interface type Digital-to-Analog conversion(D/A C) circuit is presented. To do this, the principle of the D/A C circuit was examined, and the problems that occur when extending one bit by adding individual devices were analyzed, and a bit extension method of the D/A devices using an OP-Amp. circuit was presented. As the proposed method uses the high-precision characteristics of the OP-Amp., even if an error occurs in the device, only the overall size of the output waveform is affected, and the voltage reversal phenomenon that occurs between each bit does not occur. In order to confirm the effect of the proposed method, an experimental circuit was constructed and the absolute voltage of the output and the relative error were measured. As a result, a voltage error of 0.0756% appeared, confirming that the 0.195% requirement for one bit expansion by adding individual devices was sufficiently satisfied.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.57-60
• /
• 1999

본 논문에서는 성문파에서 화자특성 계수를 추출하여 화자 인식기에 적용하고자 한다. 공분산 방법으로 음성의 잔류신호를 추정하고 이를 적분하여 성문파를 얻어낸다. 하나의 성문파 구간을 성문닫힘순간 사이가 아닌 잔류신호의 오차가 최대가 되는 순간 사이로 잡았다. 구해진 성문파를 M개의 데이터로 다시 샘플링하여 특성 벡터로 삼고 VQ기반 인식기를 사용하여 인식률을 측정하였다. 4초의 test data와 30차의 특성벡터를 사용한 경우 남성의 경우 평균 $96.08\%$, 여성에 대하여 $93.61\%$의 평균 인식률을 얻었다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.105-106
• /
• 2011

전력계통에서 비선형부하와 시변부하 사용의 증가 및 분산전원의 보급 증가로 전력품질(power quality)에 대한 관심이 증대되고 있다. 전력계통에서 전력품질은 전력신호를 통해 모니터링이 가능하다. 하지만 전력신호 상시 관측을 통한 전력품 모니터링은 많은 신호 데이터양이 필요하여 전력 신호 압축이 요구된다. 이에 따라 본 연구에서는 신호 압축 성능이 우수한 DCT(discrete cosine transform)기법을 이용하여 전력신호를 압축, 복원하는 방법을 제안한다. 그리고 DSP (digital signal processor) 보드를 통해서 압축 저장 된 신호를 오차 범위 5% 이내로 복원한다. 따라서 정전과 같은 이벤트(event)가 발생하였을 때 특정시간, 장소에서의 전압과 전류 파형을 볼 수 있게 한다. IEC 61000-4-30, IEEE std 1159에 근거하여 Matlab 프로그램 상에서의 성능을 평가하고 DSP보드를 이용하여 DCT를 이용한 데이터압축 시스템을 구현하였다.