• Journal of the Korean Society for Railway
• /
• v.13 no.2
• /
• pp.201-207
• /
• 2010

The replacement criterion of rail by accumulated passing tonnage was estimated by the bending fatigue life of rail. In order to estimate the bending fatigue life, it is basically needed to analyze bending fatigue behavior on the rail. In this study, the bending fatigue test were performed for 50kg/m and 60kg/m rails, and test specimens were distinguished by new and used rails and by the types of welded rail such as base material, thermite weld, and gas pressure weld. Also, this study analyzed the fractured surface, the position of initial crack and the bending fatigue behavior (S-N curve). Therefore, it evaluated S-N curve for welded rails according to the fracture probability. The result from this study might be used essential data in order to estimate the bending fatigue life of rail by the accumulated passing tonnage.

• Journal of the Korean Institute of Gas
• /
• v.16 no.5
• /
• pp.28-34
• /
• 2012

Material degradation of Cr steels in using for boiler tubes was studied in the relation of microstructural changes like carbide behavior and mechanical properties of hardness and creep-rupture life. The carbide dissolution was occurred in 2Cr steel of T22 during high temperature operation. And the grain refinement within martensite lath of 12Cr steel of X20 was derived by the high temperature-long time exposure. But the specific phenomena of material degradation which might be represented by hardness or creep-rupture time of the used tubes were not shown in all the tubes of T22 and X20 even in the fire-side using.

• Journal of the Korean Society for Railway
• /
• v.17 no.6
• /
• pp.391-396
• /
• 2014

In this study, the strength of magnesium-GFRP/epoxy single-lap bonded joints are experimentally evaluated with different end shapes. In order to achieve this, four different single-lap joints with different end shapes are fabricated and the failure load is measured under tensile loading tests. From the test results, the single-lap joint with a square end exhibits the lowest failure load while the single-lap joint with reverse tapering and a spew fillet has the highest stress values. It has 11.1% higher failure strength than the single-lap joint with a square end.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6D
• /
• pp.895-904
• /
• 2008

CWR (Continuous Welded Rail) may be broken when a temperature drop below the neutral temperature changes in axial force, causing tensile fracture and rail gap, in winter. Rail-breaks may lead to the damage of the rail and wheel by dynamic load, and the reduction of running safety if not detected before the passage of a train. In this study, the track and train coupled model with open gap for dynamic interaction analysis, is proposed. Linear track and train systems is coupled by the nonlinear Herzian contact spring and the complete system matrices of total track-train system is constructed. And the interaction phenomenon considering open gap, was defined by assigning the irregularity functions between the two sides of a gap. Time history analysis, which have an iteration scheme such as $Newmark-{\beta}$ method based on Modified Newton-Raphson methods, was performed to solve the nonlinear equation. Finally, numerical studies are performed to assess the effect of various parameters of system, apply to various speeds, open gap size and the support stiffness of rail.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.450-453
• /
• 2009

본 논문에서는 지진하중을 고려하여 충분한 연성거동이 가능하도록 배근한 철근콘크리트 횡하중 저항 골조(내진상세)와 고정하중과 적재하중만을 고려하여 설계한 중력하중 저항 골조(일반상세)를 대상으로 외부기둥과 내부기둥에 연결된 보의 연쇄붕괴 거동을 평가하기 위한 실험을 수행하였다. 일방향 가력실험 결과에 따르면 내진상세의 경우 대변형 상태에서 보의 하단철근의 파단이후 상단 압축철근이 인장력을 부담하면서 전체 보 부재는 축인장력이 작용을 하면서 힘-변위 곡선은 상승하는 현수작용이 발현되었다. 그러나 일반상세의 경우 충분한 현수작용이 발현되기 전에 보의 주근이 정착된 외부기둥 접합부의 파괴로 인하여 저항내력이 감소하였다.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.1-8
• /
• 1992

본 고에서는 균질화법의 정식화를 이용하여 복합재료의 거시적 균질화된 재료상수를 구하고, 이 재료상수를 이용하여 거시구조물의 변형과 응력을 구하고, 이로부터 다시 미시구조의 응력분포와 변형도를 구하는 방법을 기술하였다. 주기성을 가정한 균질화법은 복합재료 구조물의 물성평가와 거동예측에 대한 매우 적절한 수치해석 방법이다. 균질화법은 이러한 선형변형의 문제뿐만 아니라, 내압을 존재하는 빈공간 소재의 물성, 기지재료와 강화재료 계면의 미끄러짐 등으로 인한 미세 파손현상 등의 예측이 가능하다. 그외에도 탄소성 대변형 거동 이론과 균질화법을 함께 적용하여, squeeze casting에서 발생하기 쉬운 계면분리나 파단 등의 미소결함과 같은 2차 성형성의 예측도 가능하다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.6
• /
• pp.531-535
• /
• 2005

This study investigates the behavior of fatigue crack propagating between holes or holes lilted with another materials. It is experimentally and analytically confirmed that the center crack stops when its tip reaches near the center line of the holes and a small crack is initiated from the boundaries of holes or the holes filled with another materials and it propagates to final fracture. The mechanical behaviors of center crack near the another materials are also investigated. The phenomenon that this crack propagates to fracture is investigated by compliance method.

• Korean Journal of Materials Research
• /
• v.11 no.1
• /
• pp.8-14
• /
• 2001

Microstructural evolution and creep failure behavior of GTD 111 have been studied. Solidification and precipitation behaviors of the alloy during casting have been analyzed by microstructural observations. It has been found that MC carbides solidify just before the $\gamma$/$\gamma$' eutectic solidification. The ηphase was found to be formed by transformation of Ti-rich $\gamma$'phase. PFZ has formed in the vicinity of the transformed $\eta$ phase. A few MC particles, which have been identified as TaC, precipitated within the PFZ. Creep failure along grainboundary was dominant at and above $871^{\circ}C$. Creep failure above$ 871^{\circ}C$ was caused by the propagation of surface cracks and internal cracks. Creep crack has initiated at the microporosities embedded on the grainboundary. The $\eta$phase and PFZ have been found to be little or no effect on creep crack initiation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1241-1242
• /
• 2010

• Tribology and Lubricants
• /
• v.7 no.2
• /
• pp.22-27
• /
• 1991

접촉운동에 의해 재료 접촉부위의 기계적 상태의 변화가 야기될 때 에너지가 방출되며 그 중의 일부는 AE(음향방출)의 형태로 방출된다. AE가 재료의 표면과 작용해서 일어나는 표면변위(surface displacements)는 기술적으로 표면에 설치한 변위계(displacement sensor)에 의해 쉽게 측정될 수 있으며 이 측정값은 AE가 발생된 물리적인 원인을 설명해주는 여러가지 정보를 제공한다. AE측정의 용이함에 재료의 기계적 변형, 파단과구조 및 조성 등의 변화와 AE와의 밀접한 관계로 인해, 재료의 마찰 접촉시의 거동을 이해하기 위해 AE 모니터링이 점차 활발히 적용되고 있다.