• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.99-106
• /
• 1998

In order to investigate the impact properties of structural materials for LNG tank, instrumented Charpy impact tests were carried out at cryogenic temperatures. $9\%$ Ni steel showed a superior fracture resistance because of less degradation in toughness until 77 K. From the load-deflection curve obtained by an instrumented methods it was found that with the decrease of temperature from 173 K to 77 K, the peak load in the curve increased, but the total absorbed energy decreased. In addition, the energy absorbed during the crack growth was larger than one absorbed in the process of crack initiation. In SUS304L material, the energy absorbed in the process of the crack initiation was relatively large, but the energy absorbed in the process of crack growth was small, the behavior of absorbed energy was well agreed with the observations of the fracture surface which showed a relatively smooth fracture surface. The absorbed Charpy impact energy in the case of A5083 alloy was lower as compared with other steels, and some cracks were observed along the crack propagation direction at the fracture surface of 77 K.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.1
• /
• pp.61-68
• /
• 2007

Interfacial fracture energy(${\Gamma}$) between $Al_2O_3$ thin film deposited by Atomic Layer Deposition(ALD) and sputter deposited Cu electrode for embedded PCB applications is measured from a $90^{\circ}$ peel test. While the interfacial fracture energy of $Cu/Al_2O_3$ is very poor, Cr adhesion layer increases the interfacial fracture energy to $39.8{\pm}3.2g/mm\;for\;Ar^+$ RF plasma power density of $0.123W/cm^2$, which seems to come from the enhancement of the mechanical interlocking and Cr-O chemical bonding effects.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.383-390
• /
• 1998

0.93m/sec의 평균속도는 변위제어 삼점휨 실험된 콘크리트 보의 하중-변위 측정결과를 선형탄성파괴역학모델과 가상균열모델에 기초한 유한요소법으로 분석하였다. 두 모델 모두 실험결과와 잘 일치하며, 균열성장길이가 약 60∼70㎜가 될 때까지 안전된 균열성장을 보이다 불안정한 균열성장에 의해 파손되었다. 선형탄성파괴역학모델에 의한 수치해석 결과 에너지해방률은 균열성장길이에 비례해서 증가하였으며, 최대값(202N/m)에 이르게 되면 일정한 값을 유지하였다. 가상균열모델에 기초한 수치해석결과 이 연구에 사용된 하중속도와 시험편의 크기에 대해 70㎜의 완전한 파괴진행대가 평성되었으며, 이는 기존의 정적 실험결과에 대한 수치해석 결과보다 상당히 작은 값이었다.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.6
• /
• pp.235-243
• /
• 1996

The mechanical behavior ot concrete is strongly influenced by various scenarios of crack initiation and crack propagation. Recently. the study of the interface fracture and cracking in interfacial regions is emerged as an important field, in the context of the developement of high performance concrete composites. The crack path criterion for elastically homogeneous materials is not valid when the crack advances at an interface because. in this case, the consideration of the relative magnitudes of the fracture toughnesses between the constituent materials and the interface are involved. In this paper, a numerical method is presented to obtain the values of two interfacial fracture parameters such as the energy release rate and the phase angle at the tip of an existing interface crack. Criteria based on energy release rate concepts are suggested for the prediction of crack growth at the interfaces and an hybrid experimental-numerical study is presented on the two-phase beam composite models containing interface cracks to investigate the cracking scenarios in interfacial regions. In general, good agreement between the experimental results and the prediction from the criteria is obtained.

• Composites Research
• /
• v.35 no.2
• /
• pp.61-68
• /
• 2022

Composite materials have been used in aerospace industry and many applications because of many advantages such as specific strength and stiffness and corrosion resistance etc. However, it is vulnerable to impacts, these impact lead to formation of cracks in composite laminate and failure of structures. In this paper, we analyzed Mode I fracture toughness of Carbon/Epoxy laminates using acoustic emission signal. DCB test was carried out to analyze Mode I failure characterization of Carbon/Epoxy laminates, and AE sensor was attached to measure AE signal induced by failure of specimen. Fracture toughness was calculated using cumulative AE energy and measured crack length using camera. The calculated fracture toughness was applied in FE model and the result of FE analysis compared with DCB test results. The results show good agreement with between FEM and DCB test results.

• Tunnel and Underground Space
• /
• v.24 no.4
• /
• pp.275-281
• /
• 2014

The performance criteria of rockfall protection fence and reliability index were investigated considering characteristic of rockfall energy occurred at 160 cut slopes in national highway. As a result of study on statistic of variables that decide rockfall energy using Monte-Carlo simulation, the degree of slope was normal distribution type, mass of rockfall and height of slope was lognormal distribution type. The rockfall energy follows lognormal distribution because of statistical characteristic of mass of rockfall. The reliability index of rockfall protection fence was 0.678 and the failure probability of was very high as 24.9%. Proposed performance criteria of rockfall protection fence considering the scale of domestic rockfall energy is maximum 500 kJ and the range of reliability index was from 1.028 to 1.956. the failure probability of rockfall protection fence was from 14.8 to 2.5 percent if applying the performance criteria using the reliability index.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.4
• /
• pp.391-399
• /
• 2008

In this paper, we further generalize the work of Lin and Abel to the case of the first and the second order derivatives of energy release rates for two-dimensional, multiply cracked systems. The direct integral expressions are presented for the energy release rates and their first and second order derivatives. The salient feature of this numerical method is that the energy release rates and their first and second order derivatives can be computed in a single analysis. It is demonstrated through a set of examples that the proposed method gives expectedly decreasing, but acceptably accurate results for the energy release rates and their first and second order derivatives. The computed errors were approximately 0.5% for the energy release rates, $3\sim5%$ for their first order derivatives and $10\sim20%$ for their second order derivatives for the mesh densities used in the examples. Potential applications of the present method include a universal size effect model and a probabilistic fracture analysis of cracked structures.

• Electric Engineers Magazine
• /
• v.208 no.12
• /
• pp.24-31
• /
• 1999

인류의 생존을 지켜주는 것은 공기와 물이라 할 수 있다. 이처럼 소중한 공기와 물이 인간의 욕구충족을 위해 인간에 의해 파괴당하고 있다는 사실은 엄연한 현실이며 알면서도 인간 서로가 파괴해가고 있다. 아직도 우리는 지구 이외에 전체의 어느 한곳에도 우리가 이주해 할 수 있는 장소를 발견하지 못하고 있으며 달이나 화성, 목성 등 어느 위성에도 인간이 살 수 있는 징후를 찾지 못하고 있다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.3
• /
• pp.287-294
• /
• 1985

본 연구에서는 충격하중하에서 충격파괴거동에 미치는 모상입경과 제2상 형태 의 영향을 분석, 검토하기위해서, 화학성분, 마르텐사이트체적율, 연결도, 강도비등을 되도록 일정하게 하고, 우선 모상입경과 제2상의 형태(연결재와 고립재)를 변화시켜, 충격속도를 달리하였을때 얻어지는 충격하중-시간유선을 토대로하여 충격강도, 하중작 용시간, 흡수에너지 및 연성파괴거동을 고찰하였다.

• Electrical & Electronic Materials
• /
• v.5 no.1
• /
• pp.43-51
• /
• 1992

최근 에너지 절약면에서 초전도 케이블에 관심을 모으고 있다. 그러나 케이블의 수명과 신뢰성을 보장하기 위해서는 극저온 절연기술이 반드시 필요하다. 본 논문에서는 극적은 기체 질소의 절연파괴특성과 기구에 대해 보고한다. 극저온 기체 질소(300K-93K)의 절연파괴전압은 액체 질소(77K)의 경우의 1/4~1/6배정도 낮으며 온도와 기체밀도에 의존한다. 또한 비등점근처의 온도영역을 제외하고는 Paschen의 법칙이 성립한다.