• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.75.2-75
• /
• 2000

• Ceramist
• /
• v.12 no.2
• /
• pp.74-81
• /
• 2009

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.181-189
• /
• 1992

The purpose of this investigation is to examine the effects of the strengthening treatments on the mechanical properties of the flame-sprayed titania ceramic coating layer. The strengthening treatments for flame sprayed specimens were carried out in 12 different conditions in vaccum furance. The mechanical properties such as microhardness, thermal shock resistance, adhesive strength and erosion resistance were tested for the sprayed specimens after strengthening treatments. And it was clear that the mechanical properties of coating layer were much improved by the strengthening treatments. The results obtained are summarized as follows; 1. It was shown that the metallurgical bond was formed between substrate and coating layer by the strengthening treatments and that thermal shock resistance and adhesive strength were remarkably raised. 2. Microhardness of coating lay was considerably increased by the strengthening treatments. 3. Erosion resistance and porosity of coating layer were slightly improved by the strengthening treatments.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.463-470
• /
• 1996

Ceramic membrane consisting of an ${\alpha}-Al_{2}O_{3}$ support and Fe doped $TiO_{2}$ top layer was prepared by the sol-gel method. The supported Fe doped $TiO_{2}$ top layer was made by dip coating the support in a mixed sol. The microstructure of the composite membranes was studied by SEM after calcination at $550~850^{\circ}C$. After sintering at $650^{\circ}C$ for 1 hr., the average particle diameter of the Fe doped $TiO_{2}$ top layer was ~40 nm. The supported Fe doped $TiO_{2}$ composite membranes exhibited much higher heat resistance than the $TiO_{2}$ membrane. The Fe doped $TiO_{2}$ composite membrane retained a crack-free microstructure and narrow particle size distribution even after calcination up to $650^{\circ}C$.

• Proceedings of the KWS Conference
• /
• 1990.11a
• /
• pp.145-147
• /
• 1990

• Journal of Welding and Joining
• /
• v.9 no.3
• /
• pp.18-25
• /
• 1991

The purpose of this paper was to investigate the effect of deposition configuration on the mechanical properties of the flame sprayed titania ceramic coating. The sprayed deposition configuration was made in different five types with titania ceramic and Ni-base alloy on the mild steel substrate. The composite coating exhibited superior mechanical properties such as hardness, adhesive strength, thermal shock resistance and corrosion resistance, whereas the mixed coating proved to be more resistant to erosion. Especially graded coating, which consist of Ni-base alloy undercost, intermediate grade coat and titania ceramic overcost, showed excellent mechanical properties.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.461-468
• /
• 2012

This study focuses on the difference of photocatalytic activity depending on crystal structure type of nanoparticles ($TiO_2$) and nanotubes (TNT). The photodecomposition of 2-chlorophenol on the synthesized $TiO_2$, Sn-impregnated $TiO_2$, TNT, and Snimpregnated TNT were evaluated. The characteristics of the synthesized photocatalyts, TNT, Sn/TNT, $TiO_2$, and Sn/$TiO_2$ were analyzed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-Visible spectroscopy (UV-Vis), and cyclic voltammeter (CV). The water-suspended 2-chlorophenol photodegradation over $TiO_2$ (anatase structure) catalyst was better than that over pure TNT. Particularly, the water-suspended 2-chlorophenol of 10 ppm was perfectly decomposed within 4 h over Sn/$TiO_2$ photocatalyst.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.3
• /
• pp.39-44
• /
• 1991

The purpose of this investigation is to examine the effects of spraying conditions on the mechanical properties of flame-sprayed titania ceramic coating layer. Titania ceramic was sprayed onto the mild steel substrate under the various spraying conditions. Spraying distances were 100, 150, 200, 250mm respectively and pinch air pressures were 0.2 0.3, 0.4 MPa at each spraying distance. The mechanical properties such as microhardness, adhesive strength and erosion wear resistance were tested for the specimens sprayed under the various spraying conditions above mentioned. The optimum operational conditions obtained through the experimental results were 150mm of spraying distance and 0.3 MPa of pinch air pressure.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.252-258
• /
• 2002

Transparent $TiO_2$ thin films prepared by sol-gel process using the modification of titanium(IV) alkoxide showed improved thermal stability and high refraction index. Compared to the pure $TiO_2$ film, the modified $TiO_2$ films show the increased index of refraction under proper condition at pH 2.5. Transparency of these $TiO_2$ thin films were more than 80% in the visible region. It has been demonstrated that the reaction occurs in the amorphous phase: an exchange of phase results in anatase before and after 400$^{\circ}C$, in rutile over 700$^{\circ}$C form the XRD results. The particle sizes, shapes and structures of these nanoclusters in the $TiO_2$ films have been identified through a SEM and XRD. The physical properties and structures of their powders have also been studied through a SEM, XRD, TGA and DSC. The thickness and index of refraction have been determined by the analysis of ellipsometric spectra.

• Membrane Journal
• /
• v.19 no.1
• /
• pp.47-53
• /
• 2009

The aim of this paper is to prepare metal/ceramic composite ultrafiltration membranes by coating inorganic particles on a metallic hollow fiber filter. The diameter and the pore size of the filter was 2.0 mm and $2{\sim}8{\mu}m$. The metal/ceramic composite ultrafiltration membranes were obtained by a coating process of silica and titania sols on top of the metallic filter. For this purpose the method of fast freeze drying and dip-coating were used. It was found that the pore size of the membrane was about 50 nm from SEM and PMI characterization. The pore size was controlled by changing the size of the particles, sintering period and temperature.