• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.9
• /
• pp.978-988
• /
• 2005

A three-dimensional dynamic model was applied to Lake Paldang, Han River in this study. The model was calibrated and verified using the data measured under different ambient conditions. The model results were in reasonable agreements with the field measurements in both calibration and verification. Utilizing the validated model, we analyzed the spatial and temporal distributions of temperature, current, residence time, and spreading pattern of incoming flows within the lake. Relatively low velocity and high temperature were computed at the surface layer in the southern region of the Sonae island. The longest residence time within the lake was predicted in the southern region of the Sonae island and the downstream region of the South Branch. This can be attributed to the fact that the back currents caused by the dam blocking occur mainly in these regions. Vertical thermal profiles indicated that the thermal stratifications would be occurred feebly in early summer and winter. During early spring and fall, it appeared that there would be no discernible differences at the vertical temperature profiles in the entire lake. The vertical overturns, however, do not occur during these periods due to an influence of high discharge flows from the dam. During midsummer monsoon season with high precipitation, the thermal stratification was disrupted by high incoming flow rates and discharges from the dam and very short residence time was resulted in the entire lake. In this circulation patterns, the plume of the Kyoungan stream with smallest flow rate and higher water temperature tends to travel downstream horizontally along the eastern shore of the south island and vertically at the top surface layer. The model results suggest that the Paldang lake should be a highly hydrodynamic water body with large spatial and temporal variations.

• Journal of Bio-Environment Control
• /
• v.24 no.3
• /
• pp.161-166
• /
• 2015

To determine the adequate levels of light intensity and $CO_2$ concentration for mango grown in greenhouses, quantitative measurements of photosynthetic rates at various leaf positions in the tree are required. The objective of this study was to develop two-variable leaf photosynthetic models of Irwin mango (Mangifera indica L. cv. Irwin) using light intensity and $CO_2$ concentration at different leaf positions. Leaf photosynthetic rates at different positions (top, middle, and bottom) were measured by a leaf photosynthesis analyzer at light intensities (0, 50, 100, 200, 300, 400, 600, and $800{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$) with $CO_2$ concentrations (100, 400, 800, 1200, and $1600{\mu}mol{\cdot}mol^{-1}$). The two-variable model consisted of the two leaf photosynthetic models expressed as negative exponential functions for light intensity and $CO_2$ concentrations, respectively. The photosynthetic rates of top leaves were saturated at a light intensity of $400{\mu}mol{\cdot}^{-2}{\cdot}s^{-1}$, while those of middle and bottom leaves saturated at $200{\mu}mol{\cdot}^{-2}{\cdot}s^{-1}$. The leaf photosynthetic rates did not reach the saturation point at a $CO_2$ concentration of $1600imolmol^{-1}$. In validation of the model, the estimated photosynthetic rates at top and bottom leaves showed better agreements with the measured ones than the middle leaves. It is expected that the optimal conditions of light intensity and $CO_2$ concentration can be determined for maximizing photosynthetic rates of Irwin mango grown in greenhouses by using the two-variable model.

• Land and Housing Review
• /
• v.2 no.4
• /
• pp.453-461
• /
• 2011

This study is to derive a project model based on potential demand for Korean-style houses, focusing on new town detached housing sites that LH supplies and to test validity of the derived model and to present the direction and supply methods of the projects. The existing high-class new town Korean-style housing developments that have been considered were found to have little business value due to problems in choice of location and discordance of demand, so 6 types of projects were established through the methods of changes in planned scale, combined use, and subdivision of plot of land based on the results of survey. The type that has the highest business value among the project models was block-type multifamily houses, and this can be interpreted as the increase in total construction area leading to increase inrevenues of allotment sales due to economies of scale. The feasibility of mass housing model in which small-scale Korean-style houses are combined with amenities was found to be high, and if the same project conditions as those of the block-type multifamily houses are applied, the business value of the Korean-style tenement houses was found to be high. Besides, the high-class housing models within block-type detached housing areas are typical projects that the private sector generally promotes, and the construction cost was found to be most expensive with 910 million won per house. In order to enhance the business value of the Korean-style housing development, collectivization such as choice of location, diversification of demand classes, optimization of house sizes, and combination of uses is needed. And in order to adopt Korean-style houses in the detached housing sites, the adjustments and division of the existing planned plots are needed, and the strategies to cope with new demand through supplying Korean-style housing types of sites can be suggested. Also breaking away from the existing uniform residential development methods, the development method through supplying original land that is natural land not yet developed besides basic infrastructures (main roads and water and sewage) can be considered, and as the construction of more than 1~2 stories building is impossible due to the structure of Korean-style house roof and furniture. So it can be suggested that original land in the form of hilly land is considered to be most suitable to large-scale development projects.

• Journal of the Korean earth science society
• /
• v.40 no.5
• /
• pp.447-463
• /
• 2019

Sea surface wind is a fundamental element for understanding the oceanic phenomena and for analyzing changes of the Earth environment caused by global warming. Global research institutes have developed and operated scatterometers to accurately and continuously observe the sea surface wind, with the accuracy of approximately ${\pm}20^{\circ}$ for wind direction and ${\pm}2m\;s^{-1}$ for wind speed. Given that the spatial resolution of the scatterometer is 12.5-25.0 km, the applicability of the data to the coastal area is limited due to complicated coastal lines and many islands around the Korean Peninsula. In contrast, Synthetic Aperture Radar (SAR), one of microwave sensors, is an all-weather instrument, which enables us to retrieve sea surface wind with high resolution (<1 km) and compensate the sparse resolution of the scatterometer. In this study, we investigated the Geophysical Model Functions (GMF), which are the algorithms for retrieval of sea surface wind speed from the SAR data depending on each band such as C-, L-, or X-band radar. We reviewed in the simulation of the backscattering coefficients for relative wind direction, incidence angle, and wind speed by applying LMOD, CMOD, and XMOD model functions, and analyzed the characteristics of each GMF. We investigated previous studies about the validation of wind speed from the SAR data using these GMFs. The accuracy of sea surface wind from SAR data changed with respect to observation mode, GMF type, reference data for validation, preprocessing method, and the method for calculation of relative wind direction. It is expected that this study contributes to the potential users of SAR images who retrieve wind speeds from SAR data at the coastal region around the Korean Peninsula.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1035-1041
• /
• 2013

To evaluate the structural integrity and dynamic characteristic of the knuckle part of a KTX anti-roll bar, an experimental and a numerical approach were used in this study. In the experimental approach, the acceleration and strain data for the knuckle parts of the KTX and KTX-SANCHUN anti-roll bar were respectively measured to evaluate and compare its structural dynamic characteristics under the operating environments of the Honam line. In the numerical approach, the evaluation of its structural integrity was conducted using LS-DYNA 3D, and then, the reliability of the finite element model used was ensured by a comparative evaluation with the experiment. The numerical results showed that the stress and velocity field of the knuckle part composed of a layered structure of a thin steel plate and rubber were more moderate than those of the knuckle part made of only a thick steel block owing to the reduction of relative contact between the knuckle and the connecting rod. It was found that the knuckle part made of a thin steel plate and rubber was recommended as the best solution to improve its structural integrity resulting from the elastic behavior of the KTX anti-roll bar being enabled under a repeating external force.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.289-295
• /
• 1995

구조물의 동적부하에 대한 동적변형 응답을 정확히 예측하고, Over Design이나 Under Design이 아닌 합리적인 설계방안의 개발은 중요한 과제이다. 동적강도해석이나 소음 승차감과 같은 진동 및 충격에 기인하는 제반 문제를 복잡한 구조물을 대상으로 합리적으로 처리하기 위한 Dynamic Design Analysis는 높은 신뢰성의 추구와 더불어 필요불가결한 기술이 되고 있다. 동적해석 방법으로는 현재 유한요소법이 널리 사용되고 있으며 여러 종류의 범용 프로그램들이 보급되어 있는 실정이다. 그러나 특히 동적문제에 있어서는 형상이나 거동이 복잡한 구조물의 경우, 또는 차량의 차체와 같이 많은 장착물이 부착된 경우에는 유한요소법의 적용이 곤란하여, 지금까지 대처할 수 있는 유용한 방법이 없었다. 따라서 비교적 용이하고 간단하게 적용가능한 진동실험을 기초로 한 구조물의 동적 응답해석 및 설계 방안의 개발이 필요하다. 본 연구에서는 진동시험으로 얻어진 부분구조물의 응답특성과 결합특성으로부터 결합 후의 응답특성을 예측할 수 있는 방법을 전달함수합성이론을 기초로하여 프로그래밍 package화 한다. 그리고 평판구조물에 대하여 진동시험과 컴퓨터 시뮬레이션을 통하여 개발된 방법의 타당성을 검증한다. 또한 실제 차량에서 차체만의 진동시험과 엔진의 자유진동시험에 의한 시험데이터로부터 차체와 엔진이 마운트 결합된 후의 진동특성을 예측한다. 진동시험시에 입력과 출력에 노이즈가 필연적으로 혼입되어 주파수응답함수의 크기(magnitude)와 위상(phase)을 왜곡시킨다. 특히 위상의 왜곡은 복소수연산을 하는 전달함수합성법의 결과에 중요한 영향을 미치게 된다. 본 연구에서는 데이타 획득시 입력과 출력의 시간지연으로 생기는 위상왜곡을 보정하는 방법을 제시하고, 그 개선 정도를 조사한다.는 소견의 확실도로서 가능성을 표현한 것이다. 예를 들면, 진동진폭 스펙트럼상에 2X 성분이 상당히 크게 나타나 정렬불량의 가능성이 0.7 정도라고 판정하는 것 등은 이러한 수치적진리치를 이용하는 방법이다. 그러나 상기의 수치적 표현만으로는 확실도를 한개의 수치로서 대표하게 하는 것은 진단의 정밀도에 문제가 있을 것으로 생각된다. 따라서 언어적진리치가 도입되어 [상당히 확실], [확실], [약간 확실] 등의 언어적인 표현을 이용하여 애매성을 표현하게 되었다. 본 논문에서는 간이진단 결과로부터 추출된 애매한 진단결과중에서 가장 가능성이 높은 이상원인을 복수로 선정하고, 여러 종류의 수치화할 수 없는 언어적(linguistic)인 정보ㄷㄹ을 if-then 형식의 퍼지추론으로 종합하는 회전기계의 이상진단을 위한 정밀진단 알고리즘을 제안하고 그 유용성을 검토한다. 존재하여도 모우드 변수들을 항상 정확하게 구할 수 있으며, 또한 알고리즘의 안정성이 보장된 것이다.. 여기서는 실험실 수준의 평 판모델을 제작하고 실제 현장에서 이루어질 수 있는 진동제어 구조물에 대 한 동적실험 및 FRS를 수행하는 과정과 동일하게 따름으로써 실제 발생할 수 있는 오차나 error를 실험실내의 차원에서 파악하여 진동원을 있는 구조 물에 대한 진동제어기술을 보유하고자 한다. 이용한 해마의 부피측정은 해마경화증 환자의 진단에 있어 육안적인 MR 진단이 어려운 제한된 경우에만 실제적 도움을 줄 수 있는 보조적인 방법으로 생각된다.ofile whereas relaxivity at high field is not affected by τS. On the other hand, the change in τV does not affect low field profile but strongly in fluences on bot

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.4
• /
• pp.207-218
• /
• 2013

This study is based on a series of numerical modeling experiments to understand the circulation and its change in the Chunsu Bay (CSB), Yellow Sea of Korea. A skill analysis was performed for the tidal height and tidal current of the observation data using the amplitude and phase of the 4 major tidal constituents respectively for verification of modeling experimental results. As a result, most of the skill score was seen to be over 90%, so numerical model experiment results can be said to be in good agreement with the observed tidal height and tidal current. Tidal wave proceeded from the entrance of the CSB towards inside, and the tidal range gradually increased to the north. It took about 10 to 30 minutes for the tidal wave to reach to northern end. The tidal wave showed a characteristic to rotate counter-clockwise in the southern part. The tidal current flowed to the north-south direction along the bottom topography; the angle of the major axis appeared alongside the isobath. It showed the characteristics of reversing tidal current with the minor axis less than 10% of the major axis. The strength of the tidal residual current that is influenced by geographical factors including bathymetry and coastline showed the range of 1~30 cm/sec, greater in the south channel and smaller in northern Bay. Two pairs of cyclonic/anti-cyclonic eddies around Jukdo and 3~4 pairs of strong eddies at the southern part of CSB in hundreds of m to a few km size by relative vorticity derived from the tidal residual current.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2003.11a
• /
• pp.577-588
• /
• 2003

정보기술의 급진적인 발달로 경쟁이 점점 심화되어져 가고 있는 환경 속에서 경쟁적 우위를 갖기 위한 기업들의 끊임없는 노력은 계속 되고 있다 이러한 시점에 ERP(Enterprise Resource Planning: 전사적 자원관리) 시스템은 기업의 경쟁력을 재고하고 변화하는 비즈니스 환경을 예측하여 신속하고 현명하게 대처하기 위한 수단으로서의 역할을 수행하고 있으며 최근 기업뿐만 아니라 대학에서도 이에 대한 관심이 확산되고 있다. 이미 국외의 많은 대학들이 ERP 시스템을 도입한 실정이고, 국내에서는 정보화 사업의 일환으로 연세대학교가 일반 행정 업무의 효율화를 위해 SAP R/3를 도입했고 향후 학사 행정 시스템과의 통합을 모색 중이다. 정부에서도 국·공립 대학들의 행정업무효율성 제고를 위해 차세대 행정업무시스템으로 ERP 시스템 도입을 본격화하고 있다. 따라서 본 논문에서는 정보화를 추진하고자 하는 국내 대학에 ERP 시스템의 도입을 제안하였고, 기존에 선행 연구된 연구자료를 비교·분석하여 기업의 ERP 시스템 구축 성공요인을 정리하였다. 국내 대학은 ERP 시스템 도입 시 제시된 주요성공요인 등을 고려하고 지속적인 관심으로 프로젝트를 수행함으로써 보다 효과적으로 구축을 완료해야 할 것이며, 아직 국내의 사례가 충분하지 않기 때문에 본 논문에서 제시한 국내외의 사례를 살펴봄으로써 대학의 ERP 시스템 도입에 관해 빠른 이해를 할 수 있을 것이다. 끝으로 본 논문은 초기단계에 있는 국내 대학의 ERP 시스템 도입에 대학이 나가야 할 방향을 제시하였고, 앞으로 국내 대학의 ERP 시스템 도입이 증가할수록 이에 대한 연구도 계속 되어야 할 것이다.보다 더 높게 나타난 반면에, 실무계 전문가 집단은 비용이 정보시스템 보다 더 높게 나타났다는 것이다.리적 특성이론과 사용자 수용이론으로 구분하여 이 특성에 따라서 향후 개발될 3D 핸드폰 아바타의 수용도의 관계를 파악하고자 한다. 본 연구에 대한 자료 수집방법은 D대학교의 교양과목인 “사이버문화의 이해와 활용”을 수강하는 학생들을 대상으로 총 170부를 설문 조사하였으며, 수집된 설문지 중에서 불성실하게 응답한 설문지 6부를 제외한 총 164부를 유효한 설문으로 확보하였다. SPSSWIN 10.0 패키지를 이용하였으며, Cronbach's Alpha값을 통한 신뢰도 분석과 요인분석을 통한 타당성 분석을 하고, 연구변수로 선정한 각 요소들의 아바타 수용도에 미치는 영향력 정도를 파악하기 위해 회귀분석을 실시하였다. 그 결과 심리적 특성과 사용자 수용 특성은 아바타 수용도에 부분적으로 영향을 미친다는 것 결과가 나타났다.웨어 프로세스 평가와 개선 모델의 개발을 위한 기초적인 자료를 제공할 것으로 예상된다 또한, 본 연구 결과는, 우리나라 소프트웨어 조직들이 실제로 무엇을 필요로 하는지를 밝힘으로써, 우리나라의 소프트웨어 산업을 육성하기 위한 실효성 있는 정책 입안을 위한 기초 자료를 제공할 것으로 예상된다.다.를 검증하려고 한다. 협력체계 확립, ${\circled}3$ 전문인력 확보 및 인력구성 조정, 그리고 ${\circled}4$ 방문보건사업의 강화 등이다., 대사(代謝)와 관계(關係)있음을 시사(示唆)해 주고 있다.ble nutrient (TDN) was highest in booting stage (59.7%);

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.191-200
• /
• 2017

Smart work is an alternative form to enable seamless business collaboration without time and space limitations using ICT. However, smart work implementation has not produced tangible achievements and sometimes has resulted in failure. This study examined users' resistance against smart work, which is regarded as one of the most important elements for the successful implementation of smart work. The study classified elements which cause users' resistance into the work's innovative characteristics and the user characteristics based on the model of innovation resistance. It also set the degree of freedom in spatial and temporal dimension as moderating factors. This empirical research results showed that low work efficiency, unfavorable evaluation methods, and high degree of satisfaction in the way of working affected smart work users' resistance. In addition, temporal freedom had a moderating effect on the relationship between users' characteristics and their resistance. On the contrary, spatial freedom affected the relationship between their works' innovative characteristics and their resistance. The study results suggest that organizations need to set up business processes and evaluation methods first to adopt Smart work successfully.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.5
• /
• pp.203-216
• /
• 2021

Analyzing various wave interactions with oscillating wave surge converters (OWSC) is essential because they must be operated efficiently under a wide range of wave conditions and designed to extract optimal wave energy. In the conceptual design and development stage of OWSC, numerical analysis can be a good alternative as a design tool. This study performed a numerical analysis on the behavioral characteristics of the inverted triangle flap against the incident waves using open source CFD to examine the essential behavioral attributes of OWSC. Specifically, the behavioral characteristics of the structure were studied by calculating the free water surface displacement and the flap rotation angle near the inverted triangular flap according to the change of the period under the regular wave conditions. By comparing and examining the numerical analysis results with the hydraulic model experiments, the validity of the analysis performed and the applicability in analyzing the wave-structure interactions related to OWSC was verified. The numerical analysis result confirmed that the hydrodynamic behavior characteristic due to the interactions of the wave and the inverted triangle flap was well reproduced.