• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.312-316
• /
• 2012

This study evaluated the effect of polyolefine greenhouse covering film on growth of lettuce and cucumber. The growth of lettuce and cucumber plants under conventional film (polyethylene plus ethylenevinyl acetate, PE + EVA) and polyolefine (PO) film were evaluated in a greenhouse. The physical qualities of PO film, such as tensile strength and tear strength, were stronger than conventional PE + EVA film. PO film showed 4% higher transmission performance in photosynthetic active radiation (PAR) than PE + EVA film. The average day and night temperature in greenhouse under PO film were $1.5^{\circ}C$ and $0.8^{\circ}C$ higher but there was no significant difference in relative humidity compared with conventional film. Chlorophyll content of lettuce and cucumber plants grown under PO film were higher than conventional film. Growth characteristics; plant height, leaf area, fresh weight and dry weight of cucumber was shown better for PO film. The yields of cucumber and lettuce was increased 14.0% and 13.6% respectively, when the crops were grown under PO covering film greenhouse.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.127-136
• /
• 2008

Geophysical survey for establishing a wide site for the distribution of water content, wetting front infiltration due to the rainfall, and distribution of groundwater level has been performed by using 8round penetration radar (GPR) method, electrical resistivity method, and so on. On the other hand, a narrow area survey was performed to use a permittivity method such as time domain reflectometry, frequency domain reflectometry, and amplitude domain reflectometry methods for estimating volumetric water content, soil density, and concentration of contaminant in surface and subsurface. The permittivity methods establish more corrective physical parameters than different found survey technologies mentioned above. In this study for establishment of infiltration behaviors for wetting front in the unsaturated soil caused by an artificial rainfall, soil physical parameters for volumetric water content, pore water pressure, and pore air pressure were measured by FDR measurement device and pore water pressure meter which are installed in the unsaturated weathered granite soil with different depths. Consequently, the authors were proposed to a new establishment method for analyzing the variations of volumetric water content and wetting front infiltration from the responses of infiltrating pore water in the unsaturated soil.

• Applied Microscopy
• /
• v.29 no.2
• /
• pp.189-193
• /
• 1999

The response of ameloblast to long term (3 weeks) exposure to fluoride was examined in continuously erupting mandibular incisors of pregnancy rats as compared to control rats receiving a similar diet (Teklad L-356) but no sodium fluoride in there drinking water. Rats were started on water containing 0 ppm, 100 ppm, 200 ppm, and 300 ppm NaF at the beginning of pregnancy. To examine on the ultrastructural changes of the ameloblast, electron microscopy was used. The results indicated that rat incisors expressed two major changes in normal amelogenesis that could be attributed to chronic fluoride treatment. The fluoride produces marked alteration in the fine structure of ameloblast from teeth of young rats, such as large confluent distensions of the endoplasmic reticulum and swelling of isolated mitochondria, in particular on the morphology of the rough-surfaced endoplasmic reticulum. A graded series of alterations to these organelles were produced, and the severity of the changes would seem to be dependent on dose and time. This experimental data suggested that exposure prolonged of animal to high level of fluoride appears to induce morphological changes in the normal appositional growth and initial mineralization of enamel created during amelogenesis.

• Applied Microscopy
• /
• v.34 no.2
• /
• pp.145-157
• /
• 2004

The aim of the present study was to examine in detail, both at light and electron microscopical levels, the morphological variations in ameloblast of the fetal rat incisor enamel organ. Rats were started on distilled water at the beginning of pregnancy. The pups were sacrificed 11 days after delivery and animals were perfused intravascularly with glutaraldehyde and the incisors were removed. To examine on the ultrastructure of the ameloblast, the study employed primary light microscopy but electron microscopy was used to clarify some of the light microscopic finding. Longitudinal sections through the incisors of the rat show a continuous layer of ameloblasts on the labial surface of the tooth. This layer contains the entire sequence of developmental stages in enamel production. The ameloblast layer was divided into three main zones: 1) Presecretory zone, region of ameloblasts facing pulp. 2) Secretory zone, region of inner and outer enamel secretion. 3) Maturation zone, region of reduced ameloblasts. In particularly, the present study has shown that two distinctively different types of ameloblasts appear in the enamel organ during enamel maturation in the rat incisor. These two types have been designated ruffle-ended ameloblasts (rAB) and smooth-ended ameloblasts (sAB). The fluoride produces marked alteration in the fine structure of ameloblast from teeth of young rats, such as large confluent distensions of the endoplasmic reticulum and swelling of isolated mitochondria. This experimental data suggested that exposure prolonged of animal to high level of fluoride appears to induce a few dramatic changes in the normal appositional growth and initial mineralization of enamel created during amelogenesis.

• Applied Biological Chemistry
• /
• v.41 no.7
• /
• pp.516-521
• /
• 1998

Solubility patterns and gelatinization properties of two waxy rice starches, Sinsunchalbyeo and Hwasunchalbyeo, were investigated. Shapes of all starch granules were round and polygonal, and their X-ray diffraction patterns were all A type. Amylose content and water binding capacity of Sinsunchalbyeo were similar to those of Hwasunchalbyeo. The swelling powers and solubilities of two starches were increased with increasing temperature in range of $65{\sim}95^{\circ}C$, and those of Hwasunchalbyeo was higher. Iodine affinities of soluble fractions in Sinsunchalbyeo starch were higher than those in Hwasunchalbyeo at the same temperature and both were increased with increasing temperature. λmax of soluble fraction of Sinsunchalbyeo starch was highest at $75^{\circ}C$ of heating temperature. The transmittance of starch suspensions were increased rapidly at $60{\sim}65^{\circ}C$. By Rapid Visco Analyzer, initial gelatinization temperature of Sinsunchalbyeo was $67.2^{\circ}C$, and that of Hwasunchalbyeo was $68.2^{\circ}C$. In DSC analysis, onset temperature for gelatinization of Sinsunchalbyeo and Hwasunchalbyeo were $61.3^{\circ}C\;and\;62.9^{\circ}C$, respectively.

• Korean Journal of Optics and Photonics
• /
• v.9 no.4
• /
• pp.221-226
• /
• 1998

Ternary heavy metal oxide glasses in the $PbO-Bi_2O_3-Ga_2O_3$ system doped with $Er_2O_3$ were prepared and their spectroscopic properties, such as radiative transition probability, calculated and measured radiative lifetimes and cross-sections of 1.5 $\mu\textrm{m}$ and 2.7 $\mu\textrm{m}$ emissions were analyzed. Enhanced quantum efficiencies of some electronic transitions were evident mainly because of the low vibrational phonon energy ($~500cm^{-1}$) inherent in the host glasses. This seems to be the main reason for obtaining the 2.7 $\mu\textrm{m}$ luminescence which is normally quenched in the conventional oxide glasses. In addition, green and red fluorescence emissions were observed through the frequency upconversion processes of the 798 nm excitation. Non-radiative transition due to the multiphonon relaxation is a dominant lifetime-shortening mechanism in the 4f-4f transitions in $Er^{3+}$ ion except for the $^4S_{3/2}{\rightarrow}^4I_{15/2}$ transition where a non-radiative transfer to band-gap excitation of the host glasses is dominant. Melting of glasses under an inert gas atmosphere and (or) addition of the typical glass-network former into glasses is necessary in order to enhance the quantum efficiency of the transition.

• The Journal of Engineering Research
• /
• v.5 no.1
• /
• pp.73-87
• /
• 2004

The synthesis and crystallization of amorphous calcium carbonate($CaCO_3$.$nH_2 O$) obtained from gas-liquid reaction between aqueous solution of calcium hydroxide and carbon dioxide at 15~$50^{\circ}C$ are investigated by electrical conductometry, XRD and TEM. The results are as follows: The initial reaction products prior to the formation of precipitated calcium carbonate is amorphous calcium carbonate. The electrical conductivity values in the slurry are decreased during the formation of amorphous calcium carbonate which covers particle surface of calcium hydroxide and retard the dissolution of calcium hydroxide into the solution. that amorphous calcium carbonate is unstable in the aqueous solution and crystallizes finally to calcite by the through-solution reaction. While amorphous calcium carbonate crystallizes into chain-like calcite, the conductivity values are recovered rapidly and the apparent viscosity of slurry containing higher concentration of calcium hydroxide increase. At below pH 9.5, chain-like calcite separates into individual particles to form precipitated calcium carbonate. The formation and synthetic temperature range of amorphous calcium carbonate is most suitable a primary decreasing step(a-step) at $15^{\circ}C$ in the electrical conductometry.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.4
• /
• pp.83-88
• /
• 2008

Purpose: To design an anamorphic aspherical prism lens for the HMD optical system. Methods: First, we get the initial data, needed in design, which are distances between each surface etc., by analyzing user's demended specifications and by drawing geometrically the shape of prism lens by using CAD. Based on these data and using 'ode V' which is an optical design software, we could progress the optimization in which we treat the coefficients of the anamorphic aspherical surface as the principal variables. To reduce the cost in DTM manufacturing, we would optimize the optical system with the transmitting surface, existed in the direction of video device among 3 surfaces of the prism lens, remaining as a plane. Results: we could design one anamorphic aspherical prism lens which has the finite ray aberration of 15 ${\mu}m$, the distortion of 0.5%, and the MTF value of 0.3 over at 36 lp/mm for the video device of 12 mm ${\times}$ 9 mm size. Conclusions: We designed a prism lens used for HMD. This prism lens has the optical capacities of 15 ${\mu}m$ finite ray aberration and 0.5% distortion for the video device of 12 mm ${\times}$ 9 mm size, and become the optical system having the MTF value of 0.3 over at 36 lp/mm.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.41-46
• /
• 2014

The property improvement of polycarbonate coated with a multilayer film composed of an inorganic $SiO_2$ film and a photocatalytic $TiO_2$ film was studied. The $SiO_2$ film as a binder had an excellent light transmission characteristic. After the treatment with atmospheric pressure plasma, the surface of $SiO_2$ film showed the hydrophilicity, which increased the film coating uniformity with a $TiO_2$-containing aqueous solution. When $TiO_2$ film was over 200 nm thick, the absorption effect of UV rays in the range of 180~400 nm suppressed the yellowing phenomena of polycarbonate substrate. The inorganic film improved the heat resistance of polycarbonate substrates. $TiO_2$ film in the outmost under the exposure of UV rays promotes the catalytic oxidation characteristics and yields the capability to the decomposition of organic contaminants, and also increases the self-cleaning properties due to the increase of hydrophilicity. Structural stability of the polycarbonate substrate coated with inorganic $TiO_2$ and $SiO_2$ film was shown. The role of $SiO_2$ film between $TiO_2$ and polycarbonate substrate suppressed the peeling of $TiO_2$ film by inhibiting the photocatalytic oxidation effect of $TiO_2$ film on the polycarbonate substrate.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.3
• /
• pp.209-218
• /
• 2011

The present study proposes a new estimation relationship for the transmission rate of the steel breakwater which is expected to make up for the weakness points in existing hard solution for shore protection. The steel breakwater consists of the wave dissipator of the dual horizontal plates, the supporting columns and their foundations, and thus its respective designs should also be conducted one by one. Furthermore, the breakwater has to ensure both functions of shore protection and structure stabilization. The study produced experimental data for the stability and safety investigation of the steel breakwater. The forces acting on the steel breakwater were classified into two categories, one is vertical up and down loads for the pile resistance and the other was maximum difference of the vertical load acting on horizontally different position for the torsion. The study applied the stability force produced by the summation of maximum pressure at each point and the safety force acting on each point simultaneously. The regular wave corresponding to the significant wave was utilized for measuring wave pressure and force. The study showed the method for the proper position of submerged upper plate by considering occurrence frequency of tide level. The design process finally determined by trial and error is proposed in the present study.