• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.20-23
• /
• 2007

가정용 연료전지 수소 공급용 연료변환 장치는 LNG, LPG를 이용하여 수소를 제조하는 수증기 개질과 제조된 합성가스의 정제공정으로 저온/고온 전이 반응 및 선택적 산화 반응을 포함하게 된다. 이중 전체 연료변환 장치 효율은 공정중의 유일한 흡열 반응인 수증기 개질 반응기 구조와 반응열 공급용 버너에 의해 결정된다. 반응열 공급용 버너의 형식, 구조 등의 변수를 통해 본 연구진에 의해 개발된 반응구조의 최적 열원 공급 방식을 산출하고자 하였다. 이를 위하여 본 연구에서는 원통형 개질 반응기에 적용 가능한 버너의 구조, 토출 각도, 토출구의 수 등의 버너 설계 변수가 버너의 성능의 미치는 영향에 대하여 연구하였다. 연구에 사용된 버너는 적용 연료의 혼합 특성을 증가시키기 위해 혼합공간을 충분히 유지 하였으며, 버너의 구조와 연소용 기체의 토출각 및 토출구의 위치 변화를 통한 불꽃의 형태를 변화 시켜 반응기 내의 온도 분포 특성을 비교 분석하였으며, 분석 결과에 의해 원통형 개질 반응기에서 최대 효율을 가지는 버너의 구조로부터 수증기 개질 반응을 평가하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.9
• /
• pp.837-845
• /
• 2013

An airlift pump can be used to pump liquids and sediments within itself, which cannot easily be pumped up by a conventional method, by using the airlift effect. This characteristic of the airlift pump can be exploited in a DCFC (Direct Carbon Fuel Cell) so that molten fuel with high temperature may be carried or transported. The basic characteristics of airlift are investigated. A simple system is constructed, where the reservoir is filled with water, a tube is inserted, and air is supplied from the bottom of the tube. Then, water is lifted and its flow rate is measured. Bubble patterns in the tube are observed in a range of air flow rates with the parameters of the tube diameter and submergence ratio, leading to four distinct regimes. The pumping performance is predicted, and the correlation between the supplied gas flow rate and the induced flow rate of water is found.

• Journal of Aerospace System Engineering
• /
• v.15 no.3
• /
• pp.79-86
• /
• 2021

For a preliminary study on a thrust-throttleable Variable Flow Ducted Rocket, a gas generator and flow control valve were developed, and ground combustion tests were performed. The gas generator and flow control valve operated at the required performance level for parameters, such as heat-resistance, combustion-time, pressure, and temperature. The combustion characteristics of a fuel-rich solid propellant mixed with Boron/MgAl/AP, etc., were also analyzed. A Plunger-type flow control valve was designed to control the discharge flow area, and it was confirmed that the flow control valve was able to control the combustion gas flow rate and pressure. However, due to the reduction of the discharge flow area caused by adhesion of combustion products, the combustion pressure continuously increased. The analysis of the pressure increase is covered in Part 2 of this paper.

• Journal of Aerospace System Engineering
• /
• v.15 no.3
• /
• pp.87-92
• /
• 2021

In this study, a numerical approach was utilized to observe the phenomena in the ground combustion test of a gas generator for a ducted rocket with a plunger-type flow control device. The design factors were also identified through the analysis. It was observed that the pressure increase without the adhesion of the combustion product at the discharge pipe was quite similar to the analysis assuming a cone-shaped erosive burning effect. The pressure increase in most cases was similar to the analysis results when assuming the change in discharge pipe area due to the adhesion of combustion products. Moreover, it was also established that for a given grain shape and discharge flow area, the effect of the adhesion of combustion products has a significant effect on the combustion chamber pressure for cases over n=0.45.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.103-106
• /
• 2008

In this work it was studied that the effect on sub-component of engine considering change of engine inlet pressure caused by variable acceleration during flight of launcher. Also the transitional performance was predicted according to variable acceleration. Engine inlet pressure was defined as summation of propellant head in tank, ullage pressure and pressure difference of line, etc. Therefore consumption of propellant and acceleration of launcher led to change of engine inlet pressure, which affected on discharge pressure of pumps. This effect changed mass flow rate of gas generator and main combustor hence it was observed that engine performance was changed definitely.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.11
• /
• pp.806-812
• /
• 2012

Air curtains are widely used in commercial and public buildings to replace solid doors where traffic of people is predicted. At doorways where the solid door is open continuously or intermittently, an air curtain may be installed in order to reduce the flow of heat and moisture from the enclosed space to the outside. The purpose of this paper is to predict isolation performance of the single-sided air curtain when the wind is blowing. For the study, a numerical simulation is used to find the influence of various jet velocities on the efficiency of the single-sided air curtain device which is mounted at the side of the doorway. The isolation performance of the single-sided air curtain is evaluated by sealing efficiency which provides the assessment of the infiltration air ratio. According to the result of this study, the single-sided air curtain has lower sealing efficiency than downward-blowing air curtain. Therefore, for energy conservation in heating space, the single-sided air curtain is not recommended because of its low effectiveness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.725-731
• /
• 2016

This study numerically investigates the thermal performance of a 2.0-kW butane-based combustion heating system for an electric vehicle under cold conditions. The system is used for cabin space heating and coolant-based battery thermal management. ANSYS CFX 17 software was used for parametric analysis. The mass flow rates of cold air and coolant were varied, and their effects were compared. The numerical results were validated with theoretical studies, which showed an error of 0.15%. As the outside air mass flow rates were increased to 0.005, 0.01, and 0.015 kg/s, the cabin supply air temperature decreased continuously while the coolant outlet temperature increased. When the coolant mass flow rates were increased to 0.005, 0.01 and 0.015 kg/s, the air temperature increased while the coolant outlet temperatures decreased. The optimal mass flow rates are discussed in a consideration of the requirements for high cabin heating capacity and efficient battery thermal management.

• Journal of Bio-Environment Control
• /
• v.9 no.1
• /
• pp.11-19
• /
• 2000

In recent, multi-sector nutriculture in which each sectors are managed with different compositions and supplying amounts of nutrient solution is being prevalent especially in large-scale greenhouses. This study was carried out to develop an automatic mixing and supplying system of nutrient solution for the multi-sector greenhouse which can control various compositions of nutrient solution and supplying amounts for each sector. The stock solution control device could control discharge of the stock solution with device actuating time. The experimental result showed high correlation between the discharge and the actuating time. The system could make nutrient solution of various compositions and showed possibility of changing compositions of nutrient solution according to changes of growth stages or environments. Undesirable remnant nutrient-solution effect on the next supply was decreased by lowering RC of the previous nutrient solution remaining in the tank and supply pipe through rinse process. To evaluate performance of the developed system, experiments that compare N $O_3$$^{[-10]}$ , and P $O_4$$^{3-}$ concentrations of nutrient solution made in laboratory level with those made by the developed system were conducted. The experimental results showed that the deviations for N $O_3$$^{[-10]}$ , and P $O_4$$^{3-}$ concentrations of nutrient solution composited by the developed system were -2.36％ and -5.15％, respectively.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.2 s.35
• /
• pp.13-18
• /
• 2006

This paper was studied to design Process considered flexibility and reliability of suction and discharge valves. Flexibility and reliability of valves are main important factors in compressor valves design. And they are incompatible with efficiency of compressor. In this study, we have performed the optimal design of CO2 compressor valves to consider these factors. At first, we analyzed performance simulation of compressor to obtain optimal flexibility level of valves. From this simulation, we could get some important data at valve design like the optimal natural frequency and the height of retainer. After that we studied to reliability of valves corresponding to optimal flexibility level by finite element method. For each case bending stress and natural frequency were obtained by it. Also we investigated the fatigue stability to obtain optimal valve shape that ensured to reliability.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.11
• /
• pp.101-107
• /
• 2007

Jettability analysis using one-dimensional(1D) lumped parameter model has been investigated to design the industrial inkjet head with proper drop velocity and drop volume. By simplifying the inkjet head system into an equivalent electrical circuit, lumped model has been developed. Performance of the lumped model is verified by the comparison between measured results of droplet velocity and ejection volume and predicted value. Also, the jetting performance of an inkjet head is characterized by varying the design parameter and driving condition. As a result, simulation results shows good agreement with the experimentally measured value. The developed lumped model enables to easily understand the effect of dimension change and predict the jetting performance.