• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.4 s.56
• /
• pp.107-115
• /
• 2009

The number of railway tunnel design is increasing recently compare to a great number of highway tunnel design which had increased with a lot of highway construction in the 70's and 80's. Therefore, there is more or less difference of time between highway tunnel and railway tunnel. In this paper, numerical analysis on two kinds of tunnels, such as two-forked road highway ventilation tunnel and double track railway tunnel with 4.3m of center line, in cases of with support materials condition and without support materials condition were conducted. Finally, stability of two kinds of tunnels were compared and analyzed through comparing of principal stresses and deviator stresses in the near base rock of tunnels using results of numerical analysis.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.162-167
• /
• 2002

열차가 고속으로 터널에 진입하게 되면 터널 내부에서 극심한 압력 교란이 발생하게 되며 이로 인한 이명현상은 승객들에게 불쾌감을 크게 유발시키고, 열차 구조물에 작용하는 반복적인 하중변화 또한 구조상 큰 문제를 일으킬 수 있게 된다. 따라서 이를 해결하기 위해서는 터널 내부의 유동장에 대한 정확한 예측이 필요하다. 본 논문은 긴 터널을 효율적으로 해석하기 위해서 최소 차원의 공간 가정을 통하여 계산 시간을 절약할 수 있는 혼합차원 기법을 이용하여 현재 G7 시제차의 시험 운행 구간내의 터널들에 대해서 수치해석을 수행하였다. 해석 결과 터널 내부에서는 압축파, 팽창파의 상호 작용에 의한 복잡한 압력 교란이 발생하였고, 이러한 압력 변화는 열차 속도, 터널 길이, 측정위치에 따라 각각 다르게 나타났다. 따라서 터널 내부의 유동장을 정확히 예측하려면 열차 속도, 터널 길이, 열차 길이, 열차/터널 단면적 비, 측정 위치 등을 고려하여 해석을 수행하여야 한다. 이러한 수치 해석 결과는 시제차 시험 계획의 수립 및 시험기기의 선택과 설치 위치 등을 결정하는 중요한 자료로 활용될 수 있을 것이며, 고속 열차의 여압 시스템과 외부 부착 구조물에 대해서도 중요한 정보를 제공할 수 있을 것이다.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2009.04a
• /
• pp.540-547
• /
• 2009

국내도로터널 화재안전성을 확보하기 위하여 FDS를 이용하여 ISO, 도로터널 방재시설기준, Runner Hammer 터널기준의 시나리오에 따라 콘크리트 터널구조물의 내부 열역학적 특성을 예측하였다. 화재로 인한 터널내부의 온도분포를 측정하기 위하여 화염원으로부터 터널입구 방향으로 5m 마다 터널 단면의 온도분포를 추출하였고, 터널의 중심을 지나는 길이방향 단면의 온도분포를 해석하였다. 해석결과 온도는 500${\sim}$950$^{\circ}C$까지의 분포를 나타내었고 가장 높은 온도영향을 받은 Runner Hammer 터널기준의 내부 열환경 조건에서는 터널 단면이 모두 화염에 직접적으로 노출 때문에 단면전체가 800${\sim}$950$^{\circ}C$까지 상승하였다. 특히 상부부분은 900$^{\circ}C$ 이상의 고온에 장시간 노출되고 있어 깊이 50mm 지점의 온도가 250$^{\circ}C$까지 상승하였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.6
• /
• pp.1073-1090
• /
• 2018

Since the domestic utility tunnels were built mainly in the development project of the new city, they are all in the form of cut-and-cover box tunnel. But, in the case of overseas construction of utility tunnels for existing urban areas, the bored tunnel types are mainly adopted. It is reasonable to install bored tunnels in a downtown area because it is difficult to block the roads or install bypass roads due to heavy traffic and civil complaints. In order to activate the utility tunnels in bored type, it is necessary to secure optimized cross-sectional design technology considering the optimal supplying capacity and mutual influencing factors (Thermal Interference, electrolytic corrosion, efficiency of the maintenance, etc.) of utilities (power cables, telecommunication cables, water pipes, etc.). The optimal cross-section design method for bored utility tunnels is ultimately to derive the optimal arrangement technique for the utilities. In order to develop the design methods, firstly, the cases of tunnel cross-section (Shield TBM, Conventional Tunneling) in overseas shall be investigated to analyze the characteristics of the installation of utilities in the section and installation of auxiliary facilities, It is necessary to sort out and analyze the criteria related to the inner cross-section design (arrangement) presented in the standards and guidelines.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.2
• /
• pp.165-175
• /
• 2010

Recently, requirement of a long subsea tunnel has increased due to political, economical and social demands such as saving of distribution costs, improvement of traffic convenience, and regional development. Road and railroad tunnel need a shaft for construction and ventilation because of increase of tunnel length. Shaft diameter, lining sectional thickness and rebar quantity have to be determined for design of concrete lining in the shaft. A lot of structural analyses are needed for optimal design of concrete lining considering shaft diameter, load conditions and ground conditions. Design charts are proposed by structural analyses for various conditions in this study. A sectional thickness and rebar quantity can be easily determined using the proposed design charts.

• Tunnel and Underground Space
• /
• v.28 no.3
• /
• pp.247-257
• /
• 2018

High-speed trains have been developed widely in many countries in order to transport large quantity of people and commodities rapidly. When a high speed train enters a tunnel, aerodynamic resistance is generated suddenly. The resistance caused from air pressure induces micro pressure wave and discomfort to passengers in a train. Therefore, a pressure relief system should be installed in a tunnel to reduce the resistance acting against the running train in a tunnel. Additionally, the shape of a grain should be streamlined in order to reduce aerodynamic resistance caused by a high-speed train. The cross-section of a tunnel also should be carefully designed to reduce discomfort of passengers. This study represents the effect of pressure relief ducts installed between two running tunnels. The pressure relief duct was integrated with a cross-passage in order to save cost and construction time. One-dimensional network numerical simulations were carried out in order to estimate the effect of pressure relief systems.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.17 no.3
• /
• pp.249-256
• /
• 2015

Quantitative Mokpo-Jeju undersea tunnel is currently on the basis plan for reviewing validation. As for the cross section shape for express boat of 105 km line, sing track two tube is being reviewed as the Euro tunnel equipped with service tunnel. Also, 10 carriage trains have been planned to operate 76 times for one way a day. So, in this study, quantitative risk assessment method is settled, which is intended to review the optimal space between evacuation connection hall of tunnel by quantitative risk analysis method. In addition to this, optimal evacuation connection hall space is calculated by the types of cross section, which are Type 3 (double track single tube), Type 1 (sing track two tube), and Type 2 (separating double track on tube with partition). As a result, cross section of Type 2 is most efficient for securing evacuation safety, and the evacuation connection space is required for 350 m in Type 1, 400 m in Type 2, and 1,500 m in Type3 to satisfy current domestic social risk assessment standard.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2008.03a
• /
• pp.51-68
• /
• 2008

When the train enters into a tunnel a high speed, pressure waves are generated inside the tunnel. The pressure waves at propagate in a form of compression wave toward the tunnel exit and a fraction of the compression waves that arrives at the exit of the tunnel are discharged to outside of the tunnel and the remainder is reflected into the tunnel as expansion waves. The compression waves emitted from the tunnel does not radiate in a specific direction but in all directions. If the amplitude of the compression wave is great, it causes noise and vibration, and it is called "Micro-Pressure Wave." "Micro-Pressure Wave" must be considered as a decision for the optimum tunnel cross-section as the amplitude of the compression wave depends on train speed, tunnel length, area of tunnel and train. Therefore, this paper introduces the case study of Micro-Pressure Wave characteristics for determination of tunnel cross section in Honam high speed railway, the pressure inside the tunnel and the micro-pressure waves at tunnel exit were measured at Hwashin 5 tunnel in Kyungbu HSR line. At the same time. a test of train operation model was performed and then the measurement results and test results were compared to verify that the various parameters used as input conditions for the numerical simulations, which were appropriate. Also a model test was performed, in order to analysis of the Micro-Pressure Wave Mitigation Performance by Type of Hood at Entrance Portal.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.2
• /
• pp.135-148
• /
• 2013

Recently, road tunnels have become longer and the plans for long and deep road tunnel have been underway in urban areas. These long and deep tunnel excavations include NATM and TBM. Shield TBM is applied to around 80% of traffic tunnels in Europe, and approximately 30% of them in other developed countries. However, as much of equipment is imported from foreign countries at high prices and distribution rate of TBM tunnel is considerably low in Korea, NATM excavation method is commonly used. To increase TBM tunnel, it is necessary to do assure economic feasibility with the supply-demand of TBM equipment. For this, the selection of standardized TBM diameter is urgently needed. Therefore, the study aims to estimate the standardized optimum section properties of TBM by examining TBM excavation cross section utilization depending on the volume of traffic, the number of lane and its cross-section type(single or double deck), and ventilation system.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.1
• /
• pp.13-30
• /
• 2016

This paper concerns the development of an optimized TBM segmental lining design system for a subsea tunnel. The subsea tunnel is normally laid down under the sea water and submarine ground which consists of soil or rock. The design system is the series of process which can predict segmental lining member forces by ANN (artificial neural network system), analyze suitable section for the designated ground, construction and tunnel conditions. Finally, this lining design system aims to be connected with a BIM system for designing the subsea tunnel automatically. The lining member forces are predicted based on the ANN which was calculated by a FEM (finite element analysis) and it helps designers determine its segmental lining dimension easily without any further FE calculations.