• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.2
• /
• pp.122-127
• /
• 2021

This paper produces CdS thin film using ITO glass as substrates. The MDS (Multiplex Deposition Sputter System) was used to produce devices by changing RF power and deposition time. The manufactured specimen was analyzed for its optical properties. The purpose of this paper is to find the fabrication conditions that can be applied to the photo-absorbing layer of solar cells. When RF power was 50W and deposition time was 10 minutes, the thickness was measured at 64Å. At 100W, the thickness was measured at 406Å and at 150 W, the thickness was measured at 889Å. Thin films were found to increase in thickness as RF power increased. As a result of the light transmittance measurement, 550-850nm was observed to have a transmittance of approximately 70% or more when the RF power was 50W, 100W, and 150W. Increasing RF power increased thickness and increased particle size, resulting in increased thin film density, resulting in reduced light transmittance. When RF power was 100W and deposition time was 15 minutes, the band gap was calculated at 3.998eV. When deposition time is 20 minutes, it is 3.987eV, 150W is 3.965eV at 15 minutes, and 3.831eV at 20 minutes. It was measured that the band gap decreased as the RF power increased. At XRD analysis, diffraction peaks at 2Θ=26.44 could be observed regardless of changes in RF power and deposition time. The FWHM was shown to decrease with increasing deposition time. And it was measured that the particle size increased as RF power was constant and deposition time was increased.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.71-75
• /
• 2023

In this study, inorganic perovskite films with different compositions were grown by thermal chemical vapor deposition depending on the substrate and their optical properties were compared. Inorganic perovskite crystals were grown on SiO₂/Si and c-Al₂O₃ substrates using CsBr and PbBr₂, respectively, under the same growth conditions. Cs₄PbBr₆-CsPbBr₃ crystallites were grown on the SiO₂ with polycrystalline structure, while a CsPbBr₃ (100) dominant thin film was formed on the c-Al₂O₃ substrate with single crystal structure. From the photoluminescence measurement, CsPbBr₃ showed typical green emission centered at 534 nm with a full width at half maximum (FWHM) of about 91 meV. The Cs₄PbBr₆-CsPbBr₃ mixed structure exhibits blue-shifted emission at 523 nm with a narrow FWHM of 63 meV and a fast decay time of 6.88 ns. These results are expected to be useful for application in photoelectric devices such as displays, solar cells, and light sensors based on inorganic metal perovskites.

• Journal of the Korean Electrochemical Society
• /
• v.23 no.2
• /
• pp.25-38
• /
• 2020

Photoelectrochemical water splitting has been considered as the most promising technology for generating hydrogen energy. Transition metal dichalcogenide (TMD) compounds have currently attracted tremendous attention due to their outstanding ability towards the catalytic water-splitting hydrogen evolution reaction (HER). Herein, we report the synthesis method of various transition metal dichalcogenide including MoS₂, MoSe₂, WS₂, and WSe₂ nanosheets as excellent catalysts for solar-driven photoelectrochemical (PEC) hydrogen evolution. Photocathodes were fabricated by growing the nanosheets directly onto Si nanowire (NW) arrays, with a thickness of 20 nm. The metal ion layers were formed by soaking the metal chloride ethanol solution and subsequent sulfurization or selenization produced the transition metal chalcogenide. They all exhibit excellent PEC performance in 0.5 M H₂SO₄; the photocurrent reaches to 20 mA cm^-2 (at 0 V vs. RHE) and the onset potential is 0.2 V under AM1.5 condition. The quantum efficiency of hydrogen generation is avg. 90%. The stability of MoS₂ and MoSe₂ is 90% for 3h, which is higher than that (80%) of WS₂ and WSe₂. Detailed structure analysis using X-ray photoelectron spectroscopy for before/after HER reveals that the Si-WS₂ and Si-WSe₂ experience more oxidation of Si NWs than Si-MoS₂ and Si-MoSe₂. This can be explained by the less protection of Si NW surface by their flake shape morphology. The high catalytic activity of TMDs should be the main cause of this enhanced PEC performance, promising efficient water-splitting Si-based PEC cells.

• Journal of Korea Technology Innovation Society
• /
• v.12 no.4
• /
• pp.788-818
• /
• 2009

Renewable energy refers to solar energy, biomass energy, hydrogen energy, wind power, fuel cell, coal liquefaction and vaporization, marine energy, waste energy, and liquidity fuel made out of byproduct of geothermal heat, hydrogen and coal; it excludes energy based on coal, oil, nuclear energy and natural gas. Developed countries have recognized the importance of these energies and thus have set the mid to long term plans to develop and commercialize the technology and supported them with drastic political and financial measures. Considering the growing recognition to the field, it is necessary to analysis up-to-now achievement of the government's related projects, in the standards of type of renewable energy, management of sectional goals, and its commercialization. Korean government is chiefly following suit the USA and British policies of developing and distributing renewable energy. However, unlike Japan which is in the lead role in solar rays industry, it still lacks in state-directed support, participation of enterprises and social recognition. The research regarding renewable energy has mainly examinedthe state of supply of each technology and suitability of specific region for applying the technology. The evaluation shows that the research has been focused on supply and demand of renewable as well as general energy and solution for the enhancement of supply capacity in certain area. However, in-depth study for commercialization and the increase of capacity in industry followed by development of the technology is still inadequate. 'Cost-benefit model for each energy source' is used in analysis of technology development of renewable energy and quantitative and macro economical effects of its commercialization in order to foresee following expand in related industries and increase in added value. First, Investment on the renewable energy technology development is in direct proportion both to the product and growth, but product shows slightly higher index under the same amount of R&D investment than growth. It indicates that advance in technology greatly influences the final product, the energy growth. Moreover, while R&D investment on renewable energy product as well as the government funds included in the investment have proportionate influence on the renewable energy growth, private investment in the total amount invested has reciprocal influence. This statistic shows that research and development is mainly driven by government funds rather than private investment. Finally, while R&D investment on renewable energy growth affects proportionately, government funds and private investment shows no direct relations, which indicates that the effects of research and development on renewable energy do not affect government funds or private investment. All of the results signify that although it is important to have government policy in technology development and commercialization, private investment and active participation of enterprises are the key to the success in the industry.

• JOURNAL OF ELECTRICAL WORLD
• /
• s.323
• /
• pp.69-75
• /
• 2003

불투명한 경제정세의 와중에서도 전기에너지를 지탱하는 근간이 되는 파워 일렉트로닉스 분야는 확실히 그 기술개발을 향상시켜 오고 있다. 특히 파워디바이스는, 지구환경과 생활환경을 보다 쾌적하게 하기 위하여 인버터 장치 등의 각종 전력절약기기와 풍력$\cdot$태양광$\cdot$연료전지 등 클린에너지의 전력제어장치에 없어서는 안되는 반도체디바이스로 성장했다. 파워디바이스 중에서도 IGBT(Insulated Gate Bipolar Transistor)의 기술혁신은 요 20년 사이에 비약적인 성과를 거두었다. 1980년대에 제품화된 IGBT는, 반도체메모리의 초미세가공기술을 도입하면서 $5{\mu}m$에서 서브미크론의 디자인툴로 발전하여, 2000년대에 들어 칩의 전류밀도는 약 2배, 포화전압은 약 $65\%$까지 개량되었다. 이와 같은 IGBT의 변천은, 전력손실을 대폭적으로 저감시켜 에너지절약기기의 전력변환효율 향상에 공헌하고 있다. 파워디바이스의 기술진보에서 또 한 가지 잊지 말아야 할 것은 주변회로의 집적화(集積化)에 의한 고성능$\cdot$고기능화이다. 최근의 인버터용 파워디바이스로 가장 많이 사용되고 있는 파워모듈은, IGBT등의 파워칩과 그 주변회로와의 컬래버레이션에 의한 제품이다. 다시 말하면 구동회로, 전류$\cdot$전압$\cdot$온도센서 및 그것들의 보호회로가 IC(집적회로)에 편입되어 고기능$\cdot$소형화를 촉진시키고 있다. 구동회로는 LVIC (저전압집적회로)에서 HVIC(고전압집적회로)로 발전하여 전류$\cdot$온도 등의 각종 센서도 동일 칩에 설계할 수 있게 되었다. 또 센싱이나 보호기능뿐만이 아니라 출력전류의 제어를 위한 연산기능과 di/dt의 제어기능이 내장되도록 되어 있어 보다. 고성능의 인텔리전트 파워모듈(IPM)이라고 불리우는 새로운 개념의 파워디바이스가 실현되었다. 또한 패키지 기술도 내부배선 인덕턴스의 저감과 트랜스퍼 몰드패키지의 개발로, 소형화뿐만이 아니라 파워칩의 성능$\cdot$기능을 충분히 발휘할 수 있도록 개발이 적극적으로 추진되고 있다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1838-1843
• /
• 2014

Nanoimprint lithography (NIL) fabrication process is regarded as the main alternative to existing expensive photo-lithography in areas such as micro- and nano-electronics including optical components and sensors, as well as the solar cell and display device industries. Functional patterns, including anti-reflective moth-eye pattern, photonic crystal pattern, fabricated by NIL can improve the overall efficiency of such devices. To successfully imprint a nano-sized pattern, the process conditions such as temperature, pressure, and time should be appropriately selected. In this paper, a cavity-filling process of the moth-eye pattern during the thermal-NIL within the temperature range, where the polymer resist shows the viscoelastic behaviors with consideration of stress relaxation effect of the polymer, were investigated with three-dimensional finite element analysis. The effects of initial thickness of polymer resist and imprinting pressure on cavity-filling process has been discussed. From the analysis results it was found that the cavity filling can be completed within 100 s, under the pressure of more than 4 MPa.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.12
• /
• pp.909-914
• /
• 2013

CIGS is one of thin film solar cell and has been studied so much, because of the possibility of low price and high efficiency. Until now, co-evaporation and sputtering were typical method to prepare CIGS absorption layer, and a few company commercialized solar cell by these method. However, non-vacuum process which has been studied for long time has not been progressed, though the merit of low price. Especially, aerosol deposition method has not been reported, because it is difficult to prepare a large quantity of various CIGS powder. In this study, CIGS powder was synthesized by mechanochemical method and CIGS absorption layer was deposited by aerosol deposition method. The thickness of the CIGS layer was controlled by the number of deposition and the surface roughness of it was affected by the amount of flow gas. And, also, I-V curve of it appeared metallic property in the case of 'as deposition'. After heat treatment in Se-rich atmosphere, the electrical property of it changed to a semiconductor. CdS and transparent conduction layer were formed by a typical method on it for solar cell. The efficiency of cell was appeared 0.19%. Though the efficiency was low because of the disharmony in the after-process, it was conformed that CIGS solar cell could be prepared by aerosol deposition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.398-398
• /
• 2012

SnO2 나노세선은 n-형 전기적 성질과 화학적인 안정성 때문에 가스센서, 투명 전극 및 태양전지와 같은 전자소자와 광소자에 널리 사용되고 있다. 화학 기상 증착, 전자빔 증착과 전기화학증착법을 사용하여 SnO2 나노세선을 제작하고 있다. 여러 가지 증착 방법중에서 전기화학증착방법은 낮은 온도와 진공 공정이 필요하지 않으며 대면적 공정이 가능하고 빠른 성장 속도로 나노구조를 효과적으로 성장할 수 있는 장점을 가지고 있다. 본 연구에서는 전기화학증착법을 이용하여 Indium Tin Oxide (ITO) 기판 위에 SnO2 나노세선 성장하고 성장시간에 따라 형성한 SnO2 나노세선의 구조적 성질을 조사하였다. SnO2 나노세선을 성장하기 위하여 D.I. water와 Entanol을 7:3의 비율로 섞은 용액을 $65^{\circ}C$로 유지하였고, 0.015 M의 Tin chloride pentahydrate ($Cl4{\cdot}Sn{\cdot}5H2O$)를 타겟 물질로 이용하였고, 0.1 M의 Potassium chloride (KCl)를 완충 물질로 사용하였다. 전기화학증착 방법을 사용하여 제작한 ITO 기판위에 성장한 SnO2 나노세선 위에 전극을 제작하고 전류-전압 특성을 측정하였다. SnO2 나노세선이 성장되는 전기화학증착 전압을 1.2 V로 고정하고, 성장시간을 15분, 30분 및 1시간으로 변화하여 SnO2 나노세선의 구조적 특성을 분석하였다. X-선회절 (X-ray diffraction; XRD) 실험 결과는 $31^{\circ}$에서 (101) 성장방향을 갖는 SnO2 나노세선이 성장함을 확인하였고, 성장 시간이 길어짐에 따라(101) 성장방향의 XRD 피크의 intensity가 증가하였다. 전기화학증착 성장 시간이 길어짐에 따라 SnO2 나노세선의 지름이 60 nm에서 150 nm로 변화하는 것을 주사전자현미경으로 관측하였다. 이 실험 결과는 전기화학증착방법을 사용하여 제작한 SnO2 나노세선의 성장 시간에 따른 구조적 특성들을 최적화하여 소자제작에 응용하는데 도움이 된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.409-409
• /
• 2012

최근 나노크기의 미세구조 가공기술이 발달함에 따라 다양한 응용을 위한 나노소재/구조가 활발히 연구 되고 있다[1]. 그 중에서 실리콘 나노선은 태양전지, 메모리, 트랜지스터 그리고 광 공진기에 쓰일 수 있는 소재로서 기존의 실리콘 가공기술을 바로 사용할 수 있을 뿐 아니라[2], 비용 면에서 탁월한 잇점이 있기 때문에 주목 받고 있는 소재이다. 실리콘 나노선의 물리적 특성을 연구하기 위한 많은 연구가 진행되었지만, 매우 작은 크기와 높은 표면적-부피비율로 인해 생긴 독특한 특징을 완전히 이해하기에는 아직 부족한 점이 많다. 실리콘 나노선의 전류-전압특성에 영향을 미치는 요소는 도핑농도, 표면상태, 채널의 크기 등으로 다양한데, 이번 연구에서는 실리콘 나노선의 표면환경이 공기와 물 두 종류로 매질에 접하고 있을 경우에 대하여 각각 전류-전압을 측정하였다. 물이 공기와 다른 점은 크게 두 가지로 볼 수 있다. 첫째로 물의 경우에는 물에 용해된 수소이온과의 화학반응을 통하여 실리콘 표면전하가 유도되며 pH 값에 민감하게 변화한다. 둘째로 물의 유전율은 공기의 80배로서 표면부근에서의 전기장분포가 많이 왜곡된다. 이를 위하여 SOI를 기반으로 채널길이 $5{\mu}s$, 두께 40 nm, 너비 100 nm인 실리콘 나노선을 일반적인 반도체공정을 사용하여 제작하였다. 나노선의 전기적 특성 실험은 Semiconductor Parameter Analyzer (Agilent, 4155C)를 사용하여 전류-전압특성을 표면 상태를 변화시키면서 측정하였다. 실험을 통해 실리콘 나노선은 물과 공기 두 가지 표면환경에 따라 전류-전압특성이 확연히 변화하는 것을 볼 수 있었다. 동일한 전압 바이어스에서 표면에 물이 있을 때가 공기 있을 때 보다 훨씬 증가한 전류를 얻을 수 있었고(3V에서 약 2배), 비선형적인 전류-전압특성이 나타남을 관찰하였다. 본 발표에서는 이러한 실험결과를 표면에서의 전하와 정전기적인 효과로서 정성적으로 설명하고, 전산모사결과와 비교분석 하고자 한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.75.1-75.1
• /
• 2010

Dye sensitized solar cells(DSSCs) have been extensively studied due to their various advantages such as low production cost, colorful design, and eco-friendly process. Long optical path length is one of the most effective method to improve light harvest efficiency for DSSCs. Multi-layered $TiO_2$ nano-structured film with scattering layer has been studied to generate scattering effect by many researchers. It was expected that the difference of refractive index between $TiO_2$ particles and glass frit would generate the light scattering effect and provide the long optical path length. Therefore, to enhance the scattering effect, the frits of $Bi_2O_3-B_2O_3$-ZnO glass system that has the different refractive index were added to $TiO_2$ pastes in this study. First of all, the absorbance and haze factor of $TiO_2$ electrode with dyes and the refractive index of glass frit and $TiO_2$ were measured, respectively. To study the effect of frits, the efficiencies of DSSCs added glass frit and without glass frit were compared. Our results showed slightly higher efficiency with the different absorbance and haze factor of $TiO_2$ and glass frit. It was considered that the light scattering effect would be improved with adding frits to $TiO_2$ paste. Our preliminary studies will be useful for increasing efficiency of DSSCs.