• Journal of Korean Society of Steel Construction
• /
• v.25 no.2
• /
• pp.153-164
• /
• 2013

In this paper, lateral-torsional buckling(LTB) strength of HSB800 high strength steel plate girder with monosymmetric section under uniform moment was evaluated by nonlinear analysis. The unbraced length in inelastic LTB range was considered for the sections whose smaller or larger flange is in compression with slender, noncompact and compact web. Analyses of SM490 steel girders were first performed with the single-panel and three-panel model to judge the validity of the constructed models by comparing those results with Eurocode 3, AASHTO and AISC codes. By using the same models, LTB strength of HSB800 girder was evaluated and it was found that the sections whose smaller flange is in compression with noncompact flange-slender/noncompact web could not reach the flexural strength of the design codes.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.40-49
• /
• 2004

Phyllostachys pubescens planted in the Nambu Forest Experiment station in Jinju city of Gyongnam province was used, to investigate the physical and mechanical property of bamboo in this study. The ages of the P. pubescens were 1, 2 and 3 years, respectively. This experiment was carried out in August and January. The P. pubescens were divided into upper, middle and lower parts according to the growing points. The physical and mechanical properties of the P. pubescens were investigated before and after treatment of hot water and microwave irradiation. 1. The upper part of the P. pubescens indicated the highest static MOE according to the growing points. The range of the static MOE was from 70,000 to 110,000kgf/cm². 2. When P. pubescens were treated with hot water of 95℃, the ratio of softening was about 10~30%. 3. As microwave irradiation time was increased, the MOE values was decreased in both green and water-saturated bamboos. For the irradiation time of 20 and 30 seconds, the static MOE of P. pubescens was decreased up to about 50% comparing with non-treated.

• Journal of Korean Society of Forest Science
• /
• v.77 no.2
• /
• pp.252-257
• /
• 1988

This study was carried out to investigate the physical and mechanical properties of sawdust boards combined with sycamore and polypropylene-net flakes. Both the sycamore and polypropylene-net flakes were adjusted to the sizes of $1.0{\times}1.0$, $1.0{\times}2.0$, and $1.5{\times}1.5cm^2$ and these flakes were mixed at 1, 2, 3, and 4% levels based on ovendry weights of sawdusts, respectively. The results obtained in this study were summarized as follows : 1. Thickness swellings of sawdust boards combined with sycamore flakes decreased with the increase of mixture levels and similar effects were also recognized in combination with polypropylene-net flakes. 2. Moduli of rupture both in sawdust boards combined with sycamore and polypropylene-net flakes increased with the increase of their mixture levels, and sawdust boards combined with sycamore flakes of $1.0{\times}2.0cm^2$ size and polypropylene-net flakes of $1.5{\times}1.5cm^2$ size showed higher moduli of rupture than control boards. 3. Moduli of elasticity both in sawdust hoards combined with sycamore and polypropylene-net flakes increased with the increase of their mixture levels as in moduli of rupture. 4. The physical and mechanical properties of sawdust boards combined with sycamore and polypropylene-net flakes were mainly dependent on aspect ratio of sycamore flakes and size of polypropylene-net flakes respectively, and these properties were improved with the respective increase of aspect ratio and size.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.470-479
• /
• 2010

In this study, the visual grading based on the visual characteristics and structural timber bending test were conducted for domestic yellow poplar dimension lumber. Structural performance of domestic yellow poplar dimension lumber was conducted through the evaluation of strength and stiffness. Visual grading rule of yellow poplar dimension lumber did not exist in Korea. Visual grading of yellow poplar dimension lumber was performed according to the NSLB (Northern Softwood Lumber Bureau) standard grading rules including several hardwood dimension lumber. The allowable bending stress was calculated from the results of a visual grading. Compared with NDS (National Design Specification), the yellow poplar dimension lumber showed enough strength for structural uses. In addition, the visual grading was performed according to the KFRI (Korea Forest Research Institute) grading rule to calculated allowable bending stress and to evaluated the feasibility. The yellow poplar was classified into the pine groups by the KFRI criteria regulated by specific gravity. Allowable bending stress based on weibull distribution had became highly than KFRI criteria, as No. 1 (10.0 MPa), No. 2 (7.4 MPa) and No. 3 (4.1 MPa). And the availability of yellow poplar dimension lumber for structural uses had been confirmed. The Modulus of Elasticity (MOE) of domestic yellow poplar dimension lumber had not met the NDS and KFRI criteria. However, for the use of domestic yellow poplar, average values of MOE which obtained through this test were suggested as design value for domestic yellow poplar. Design values were supposed No. 1, 2 (9,000 MPa) and No. 3 (8,000 MPa).

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.238-246
• /
• 2022

This paper summarizes the development and evaluation of the reinforcement details of CFRP plates to improve the bending performance of wooden beams. In this study, the reinforcing technology using high-strength bolts for the end of beam were developed as reinforcement details for reinforcing wooden beams with CFRP plates by EBM method. In order to evaluate the bending performance, a bending test was conducted for the specimens with details of reinforcement such as the EBM method and the NSM method. From the experimental results, the EBM specimens without end restraints had both the CFRP plate attachment failure and the splitting failure of the wood. In the load-displacement curve, the non-reinforced specimens exhibited linear elastic behavior and then brittle fracture after the maximum load. The maximum load of the specimens reinforced by the EBM method increased by 31.5~63.0% compared to the non-reinforced specimens, and the maximum load according to the end restraints of the high-strength bolts increased by 24.0%. Based on the reinforcement amount of the same CFRP plate, EBM reinforcement was 2.67 times larger in maximum load increase rate than NSM reinforcement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.401-409
• /
• 2006

This study presents basic information on the mechanical properties and long-term deformations of high-strength steel fiber reinforced concrete(HSFRC). The Influence of steel fiber on modulus of elasticity, compressive, splitting tensile and flexural strength, and drying shrinkage and creep of HSFRC are investigated, and flexural fracture toughness is evaluated. Test results show that Test results show that the effect of steel fibers on the compressive strength is negligible, and the modulus of elasticity of HSFRC increased with the increase of fiber volume fraction. And the effect of fiber volume fraction($V_f$) and aspect ratio($l_f/d_f$) on tensile strength, flexural strength and toughness is extremely prominent. It is observed that the flexural deflection corresponded to ultimate load increased with the increase of $V_f$ and $l_f/d_f$, and due to fiber arresting cracking, the shape of the descending branch of load-deflection tends towards gently. Also, the effect of addition of various amounts of fiber on the creep and shrinkage is obvious. Especially, the effect of adding fibers to high-strength concrete is more pronounced in reducing the drying shrinkage than the creep.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.14 no.4
• /
• pp.423-434
• /
• 2001

In this paper, a three-span continuous box girder is analysed by using elastic equation based on energy method, concerning the behaviour with the effects of bending and pure torsional moment. The statically indeterminate forces of a three-span continuous curved box girder are calculated by applying the principle of least work to this elastic equation. The influence line of shear force, bending moment, pure torsion, displacement and angle of rotation due to unit vortical load and unit torque for curved box girder are obtained. The internal forces of the curved box girder which the actual load is applied can be calculated using the influence line obtained from this study.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.347-356
• /
• 2006

In this paper, practical nonlinear inelastic analysis method of 3-dimensional steel structures accounting for gradual yielding with fibers on a section is developed. Geometric nonlinearities of member(p-$\delta$) and frame(p-$\Delta$) are accounted for by using stability functions. Residual stresses are considered by assigning initial stresses to the fiber on the section. The elastic core in a section is investigated at every loading step to determine the axial and bending stiffness reduction. The strain reversal effect is captured by investigating the stress change of each fiber. The proposed analysis proves to be useful in applying for practical analysis and design of three-dimensional steel frames.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.177-184
• /
• 1997

In this paper, numerical methods are developed for solving the elastica of simple beams with variable-arc-length subjected to a point loading. The beam model is based on Bernoulli-Euler beam theory. The Runge-Kutta and Regula-Falsi methods, respectively, are used to solve the governing differential equations and to compute the beam's rotation at the left end of the beams. Extensive numerical results of the elastica responses, including deflected shapes, rotations of cross-section and bending moments, are presented in non-dimensional forms. The possible maximum values of the end rotation, deflection and bending moment are determined by analyzing the numerical data obtained in this study.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.3
• /
• pp.11-21
• /
• 2008

A linear and non-linear analysis for plates and shells with arbitrary edge supports subjected to various loading was presented. The 9-node ANS(Assumed Natural Strain) hell element was employed and the spring element, which could express an arbitrary edge support using the six degrees of freedom, was introduced. For the application of his analysis, the plates and shells with various edge supports were analyzed, and the ending behavior with these edge supports were obtained accurately. For these edge supports, particularly elastic edge support was simulated by six springs and reasonable results were obtained. The results show that the present method can be widely used to analyze the bending behavior of plates and shells with arbitrary edge conditions.