• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.391-396
• /
• 2014

Polymer microneedles can be fabricated by a micromolding method, an easy and cost-effective method. However, it is not easy to achieve uniform coating with an aqueous coating solution due to hydrophobic surface of polymer microneedles. 3-Dimensional coating polymer microneedles could deliver more than twice as much dose as in-plane metal microneedles by increasing coating area and the number of microneedles per unit area. A uniform coating was not obtained by addition of coating additives in the coating solution. The satisfied coating was achieved by treatment of surface of polymer microneedle with metal deposition and UV/ozone, and UV/ozone treatment was an ultimate surface treatment method based on biological safety. Calcein coating polymer microneedles were prepared by using UV/ozone treatment and followed dip-coating, and they delivered calcein in porcine skin successfully after 15 min of insertion.

• Journal of Adhesion and Interface
• /
• v.20 no.3
• /
• pp.102-109
• /
• 2019

The material constitution of multi-layered thin film coated on the PET base film was analyzed using ATR FT-IR and pyro GC/MS combination. The cross section of the film was acquired by cracking the film after dipping in liquid nitrogen and was observed using optical microscope. Total thickness of the coated film was $70{\mu}m$ and three layers were observed. Since each layers were too thin to analyze directly except the surface layer, analyzable area of each layers were exposed by using a proper solvent and were investigated using ATR FT-IR and pyro GC/MS. Results shows that three layers were commonly consisted of urethane-acrylate copolymers. Also, inorganic and/or metal inclusions detected by XPS and SEM-EDAX were exhibited by nano size $SiO_2$ particles in layer(1) and aluminum flakes in layer(2).

• Polymer(Korea)
• /
• v.29 no.3
• /
• pp.288-293
• /
• 2005

Osmotic granule system which is one of the drug delivery systems has been developed to improve manufacturing process and other problems of tablet osmotic systems. It consists of water swellable seed layer, nifedipine drug layer, and drug release controlled membrane layer and manufactured by fluidized bed coater. The granule size and mombrane thickness can be controlled by various amounts of seed and coating solution, respectively. It could be observed that the morphology of osmotic granule was different at each coating step as well as type of coating solution. The bigger the size of granule, the slower the release rate was observed due to decreasing the total specific surface wed of granule. Also, it was observed that the increase of membrane thickness was caused to retard the dissolution of nifedipine due to decreasing the water absorption rate. The drug solubility for dissolution media is greatly affected to nifedipine release. From these results, we assured that osmotic granule can be fabricated by fluidized bed coating methods, and the appropriate release profile could be controlled by the controlling of bead size, membrane thickness and dissolution media.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.4
• /
• pp.324-328
• /
• 2009

The internal short-circuit between cathodes and anodes has been known to be a critical concern for the safety failures of lithium-ion batteries, which is strongly influenced by the thermal stability of separators. In this study, to effectively suppress the internal short-circuit failures, we developed a new composite separator with the improved thermal stability compared to conventional polyolefin-based separators. The composite separators were prepared by introducing a ceramic coating layer ($Al_2O_3$/PVdF-HFP) onto both sides of a polyethylene (PE) separator. The microporous structure of ceramic coating layers is determined by controlling the phase inversion of coating solutions and becomes more developed with the increase of nonsolvent (water) content. This structural change of ceramic coating layers was observed to greatly affect the thermal stability as well as the electrochemical performance of composite separators, which was systematically discussed in terms of phase inversion.

• Korean Journal of Materials Research
• /
• v.6 no.7
• /
• pp.742-751
• /
• 1996

Ti-48Al(at.%) specimens were coated with Al-21Ti-23Cr(at.%) film by RF magnetron sputtering. Ti-48Al specimen coated at 200, 0.8Pa and 573K showed the best oxidation resistance property in the isothermal oxidation test. Al-21Ti-23Cr film was amophous after depostion, but crystallized and fromed a protective ${Al}_{2}{O}_{3}$ layer on the surface during oxidation. Ti-48Al specimens coated at 573K have been sassessed by isothermal oxidation test for 100 hours at 1073K, 1173K and 1273K. The mass gain curves showed that parabolic stage continued at al tested temperature range in isothermal oxidation test, and the excellent oxidation resistance is attriutable to the formation of a protective ${Al}_{2}{O}_{3}$ layer on the surface of Al-21Ti-23Cr film. After oxidation test at 1273K, the matrix of Al-21Ti-23Cr film had transformed into TiAlCr phase due to the depletion of Al during oxidation and the diffusion of Ti from the substrate, and the extent of mass gain of the specimen increased compared with that of specimens tested at lower temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.176-176
• /
• 2011

경사 코팅법은 증발 물질이 기판에 수직으로 입사하는 기존 코팅방법과 다르게 증발물질이 기판과 $90^{\circ}$ 이하의 경사각으로 입사하도록 하여 코팅하는 방법이다. 이러한 경사 코팅법은 각도를 달리함으로 인해 비스듬한 기둥, 나선형, C-형, S-형, zigzag 구조 등의 정교하고 폭넓은 박막을 형성 할 수 있다. 이러한 경사 코팅법은 경사굴절 광학필터, 선형 편광 등의 광 산업계에서 널리 사용되고 있다. 본 연구에서는 경사 코팅법을 이용하여 마그네트론 스퍼터링법으로 Al 박막을 제조하였고 다양한 경사 각도에 따른 조직의 특성과 내식성 등을 평가하고 비교하였다. 기판을 $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, $90^{\circ}$의 다양한 각도로 위치시켜 냉연강판 및 Si 웨이퍼에 단일층 또는 다층으로 Al 박막을 코팅하였다. 박막의 구조를 확인하기 위해 전자현미경(SEM)을 사용하였으며 기판의 위치에 따른 변화를 관찰하기 위해 시편을 좌, 우, 중간으로 구분하여 분석하였다. Al 박막이 단층일 경우 회전각도 $60^{\circ}$에서 치밀한 조직이 관찰되었으며 이것은 표면의 반사도와 표면조도 결과와도 유사하게 나타났다. 다층 박막에서는 회전각도 $45^{\circ}$에서 아주 치밀한 조직이 나타났으며, $3{\mu}m$ 두께로 코팅한 시편의 염수분무 시험 결과 120시간 경과 후에도 적청이 발생하지 않았다. 이것은 기존의 방법이 약 72시간에서 적청이 발생하는 것과 비교할 때 경사 코팅법으로 코팅된 시편의 내식성이 현저히 향상됨을 나타낸다. 따라서 반응성이 높고 쉽게 산화가 일어나는 철강제품의 부식 방지를 위해 경사 코팅법으로 Al 박막을 제조한다면 치밀한 조직으로 인해 얇은 두께에서도 부식이 발생하는 시간을 연장시켜 제품의 내구수명을 연장시킬 수 있을 것으로 기대된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.68.1-68.1
• /
• 2010

염료감응형 태양전지에서 가능한 광전자의 이동경로에 대해 살펴보면 빛 에너지를 흡수한 루테늄계 염료는 기저상태에서 여기상태로 전이한 후 광전자의 반도체 전도띠로 전자주입이 이루어진다. 이러한 전자 중 일부는 반도체산화물의 트랩으로의 전이와 트랩에서 염료 기저상태로의 전이가 일어나고 일부 전자는 전해질의 이온종 또는 산화된 염료와 재결합하는 현상이 일어난다. 본 연구에서는 이러한 전자의 재결합을 막고자 p형 반도체인 NiO paste를 제작하여 $TiO_2$ 광전극 층 위에 코팅하였다. 코팅된 NiO 층은 홀수용체로서 염료에 전자를 제공해 주는 역할과 동시에 $TiO_2$ 가전도대로 이동되었던 전자들이 염료의 기저상태의 홀이나 전해질로의 전자 유입이 이루어지는 전자의 재결합을 막는 방벽의 역할을 동시에 하게 된다. 제작된 염료감응형 태양전지 셀의 에너지 변환효율 특성을 알아보기 위하여 1000 W Xe Arc Lamp와 Air Mass 1.5, filter가 장착된 Thermo-Preal (USA) Solar simulator system을 사용하여 개방전압 (Voc), 광전류 (Isc), fill factor (FF), 에너지변환 효율 (${\eta}$)을 조사하였으며 광학현미경을 통해 염료의 흡착 정도를 비교해 보았다. NiO의 코팅 두께나 NiO 나노입자 크기에 따라 염료감응형태양전지에서 에너지변환효율에 미치는 영향을 조사하였다. NiO가 코팅되지 않은 $TiO_2$ 광전극과 비교해 볼 때 NiO 코팅시 Voc와 Isc의 증가로 인해 에너지변환효율이 20% 이상 향상되는 것을 볼 수 있었다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.6
• /
• pp.455-463
• /
• 2009

코발트 보호막 코팅이 적용된 페라이트계 스테인리스 스틸인 STS 430과 STS 444 소재에 대해 고체산화물 연료전지용 금속연결재로서의 고온 산화 특성에 대해 살펴보았다. 코발트 코팅층은 $800^{\circ}C$ 고온 산화 후 코발트 산화물 및 $Co_2CrO_4$, $CoCr_2O_4$, $CoCrFeO_4$ 등과 같은 코발트가 함유된 스피넬 상을 형성하였다. 또한 페라이트계 스테인리스 스틸과 코발트 코팅의 계면에서 크롬과 철이 함유된 치밀한 산화층을 형성하여 금속연결재 표면의 스케일 성장속도를 감소시키고 금속연결재 내에 함유된 크롬의 외부 확산을 효과적으로 억제하였다. 한편 STS 430은 고온 산화 후 표면에 형성된 스케일 하부에 $SiO_2$와 같은 내부 산화물이 형성된 반면 STS 444는 표면 스케일 이외에 다른 내부 산화물은 확인되지 않았으며 고온에서의 면저항 측정 결과, 코발트가 코팅된 STS 444의 전기 전도성이 STS 430 보다 우수한 것으로 나타났다.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.67-72
• /
• 1998

Due to excellent corrosion resistance, in particular against sea water, Al-2wt.$\%$Zn alloys have been used as the sacrifice anode material for tube of the ORV. Al-2wt.$\%$Zn alloys thermal-sprayed coating, however, were spalled on the lower part of ORV due to the lack of bonding strength between base material and coating layer and the dropping energy of sea water, To overcome the problems of the thermal spray coating, we developed the cladded tube manufacturing process by coextrusion of the clad and base metal. The corrosion resistance of cladded tube was improved by two times at least, compared with that of the present thermal spray coated vaporizer tubes.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.4
• /
• pp.521-528
• /
• 2021

In this study, to repair damaged economizer fin tubes on ships, sealing treatment was performed after applying arc thermal spray coating technology using Inconel 625. A solid particle erosion (SPE) experiment was conducted according to ASTM G76-05 to evaluate the durability of the substrate, thermal spray coating (TSC), and thermal spray coating+sealing treatment (TSC+Sealing) specimens. The surface damage shape was observed using a scanning electron microscope and 3D laser microscope, and the durability was evaluated through the weight loss and surface roughness analysis. Consequently, the durability of the substrate was superior to that of TSC and TSC+Sealing, which was believed to be owing to numerous pore defects in the TSC layer. In addition, the mechanism of solid particle erosion damage was accompanied by plastic deformation and fatigue, which were the characteristics of ductile materials in the case of the substrate, and the tendency of brittle fracture in the case of TSC and TSC+Sealing was confirmed.