• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.14-17
• /
• 2009

본 연구에서는 장대교량에서 케이블의 장력을 간편하게, 그리고 자동적으로 추정할 수 있는 저비용 무선장력계측시스템을 개발하였다. 개발된 시스템은 크게 비용이 저렴하고 설치 및 관리가 용이한 무선 기반 하드웨어와 케이블에서 계측된 가속도 데이터로부터 장력을 자동으로 추정하여 주는 내장 (Embedded) 자동화 소프트웨어로 구성된다. 저비용 무선 기반 하드웨어는 연산능력을 가진 무선계측유닛과, 계측 신호개선을 위한 신호처리보드, 그리고 상용 MEMS 가속도계로 구성되었으며, 내장 자동화 소프트웨어는 계측된 신호의 주파수 분석을 위한 FFT 모듈, 케이블의 푸리에 스펙트럼으로부터 고유진동수를 자동으로 추출하기 위한 자동 피크 추출(Peak-picking) 알고리즘 모듈, 그리고 추출된 고유진동수를 활용하여 케이블의 장력을 추정하는 진동법 모듈로 구성되었다. 개발된 시스템의 검증을 위하여, 사장교의 케이블 축소모델을 제작하고 케이블 모델에 다양한 장력과 새그를 주어 진동실험을 수행하였다. 실험 결과, 개발된 시스템은 케이블 모델의 주파수응답스펙트럼으로부터 고유진동수를 정확하게 추정하였으며, 장력과 새그의 크기에 상관없이 매우 정확한 장력을 추정하였다.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2452-2454
• /
• 2000

현재, 전차선의 트롤리선을 설치하는 것은 수작업에 의해 행해지고 있어 작업의 효율화와 함께 최적의 장력제어가 필요하다. 케이블을 새롭게 가설하는 장치는 케이블을 릴에 감아 올릴 필요성은 거의 없기 때문에 케이블을 풀어주는 속도와 로드셀에 의해 장력을 검출하고 장력을 발생하는 하드웨어 구성방법을 연구하는 것이다 본 연구는 현수형 케이블(Catenary Cable)의 동적 모델링을 작성한다. 이 시스템에 대하여 교류서보 전동기를 이용한 장력 발생장치를 모델링한다. 현수형 시스템의 장력계측 장치는 하중변환기(load cell)를 사용하고 수학적 모델링을 행한다. 장력계측 장치에 관해서 스프링 저울을 이용해 출력을 비교 검토한 결과, 인장력을 계측하는 장치로서의 유효성을 확인하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.295-311
• /
• 2021

In this study, an experiment was carried out on the field applicability of tension measuring devices of the cables in cable-stayed bridges. The vibration method was used to estimate the tension of cables of cable-stayed bridge, and the mode characteristics of the cable were analyzed using a cable tension measuring device. GTDL360, NI Module, and 9 Axes Motion Sensorwere applied to estimate the cable tension of five target bridges. Numerical analysis of the five target bridges was conducted to analyze the natural frequency of the cable and cable tension. The estimated tension of the cable based on field measurements and estimated tension of cable by numerical analysis were compared with the estimated tension of the cable based on field measurements. The analysis showed that the measured tension of the cable based on field measurements was within the margin of error. Therefore, it is safe to apply these measuring devices to the site. As a result of comparing and analyzing the values of the acceleration-based cable estimation tension and numerical analysis of the field demonstration bridge, the acceleration-based cable estimation of tension is deemed appropriate within the allowable range. On-site applicability analysis revealed limitations of the measuring devices, such as the installation location of sensors and weather conditions, so continuous follow-up research on smart cable tension measuring systems is expected.

• Proceeding of KASS Symposium
• /
• 2008.05a
• /
• pp.189-194
• /
• 2008

The main object of this paper is that it's possible to monitoring the deformation of cable in the tensegrity structure. always monitoring system of Fiber Bragg Grating(FBG)Sensor is described. The measurement of parts on the cable is very important. We make an experiment with measuring deformation of cable in the tensegrity structure to the pressure conditions. In the result of experiment, the fiber sensors showed good response to the pressure conditions. Therefore, We could calculate the deformation of cable structure and be possible health monitoring of the tensegrity structure.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.127-134
• /
• 2005

Design and construction of long-span bridge are recently increasing by development of computer technology. Specially, cable stayed bridge and suspension bridge having cable component are representative of long-span bridge may do. Therefore, this paper a present a methodology for cable tension force monitoring in cable-stayed bridge under construction using acceleration data acquired by the vibration method. To improve accuracy construction, all stay cables are measured, according to 4-step construction stage and change of temperature.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.120-129
• /
• 2023

Hanger cable tension is a major response that can determine the integrity and safety of suspension bridges. In general, the vibration method is used to estimate hanger cable tension on operational suspension bridges. It measures natural frequencies from hanger cables and indirectly estimates tension using the geometry conditions of the hanger cables. This study estimated the hanger cable tension of the Palyeong Bridge using a vision-based system. The vision-based system used digital camcorders and tripods considering the convenience and economic efficiency of measurement. Measuring the natural frequencies for high-order modes required for the vibration method is difficult because the hanger cable response measured using the vision-based system is displacement-based. Therefore, this study proposed a back analysis technique for estimating tension using the natural frequencies of low-order modes. Optimization for the back analysis technique was performed by defining the difference between the natural frequencies of hanger cables measured in the field and those calculated using finite element analysis as the objective function. The direct search method that does not require the partial derivatives of the objective function was applied as the optimization method. The reliability and accuracy of the back analysis technique were verified by comparing the tension calculated using the method with that estimated using the vibration method. Tension was accurately estimated using the natural frequencies of low-order modes by applying the back analysis technique.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.31-37
• /
• 2008

As transmission line is installed by manual operation, it is necessary to scheme the automatic system for stringing transmission wire. For this necessity, the objective of this paper is developed automatic control system for a stringing of transmission wire. In this paper, transmission wire with suspended pattern and ac servo motor for torque generating are modeled. On the basis of wire model, algorithms to determine the reference tension is presented, so as the dip of transmission wire is keep constancy. The control scheme is proposed by the ac servo motor for torque generation and a load cell for a detected tension of transmission wire and implemented. We experimentally show that the performance of the tension response is satisfactory. And also proposed scheme verified the utilities for tension control of transmission wire.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.440-441
• /
• 2008

본 논문은 현수형 송전 케이블과 장력발생 교류 서보전동기의 모델을 나타내고 송전케이블의 이도를 일정히 유지하기 위한 장력을 계산하는 알고리즘을 나타내었다. 현수형 송전선 특성에 기초하여 로드셀을 이용한 장력측정에 의해 송전선 가설 시스템의 구성법이 제안되었다. 가설시스템은 장력 발생장치에 교류서보 전동기를 이용하고 케이블의 장력계측 장치는 하중변환기(load cell)를 사용한다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.205-213
• /
• 2009

This study was planned to develop monitoring system of cable force to resolve cable force of cable-stayed bridge efficiently in a long-term plan. In the proposed monitoring system, firstly data are sampled from real-time acceleration record, secondly these sampled data are frequency analyzed by using the FFT(Fast Fourier Transform) algorism and lastly the analyzed results are averaged and generalized. For evaluating the applicability of this monitoring system, field loading test has performed in real cable-stayed bridge. In comparison with cable force by field manual calculation and cable force of monitoring system by semi-automatic calculation, the difference of calculated cable forces has within 1% error range and it is acceptable range. Additionally within negligible 5% error range of difference has occur between field manual calculation and monitoring system by automatic calculation. so monitoring system in this study has been verified to be reliable.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.12a
• /
• pp.217-220
• /
• 2000

현재, 선박용 로프제조에서 로프의 제조 공정은 수작업에 의해 행해지고 있어 작업의 효율화와 품질의 균질화를 위해서 최적의 장력제어가 필요하다. 본 연구의 목적은 와이어 로프 제조공정의 자동화이고 로프의 제조 공정에서 장치는 로프를 릴에 감아 올릴 필요성은 거의 없기 때문에 케이블을 풀어주는 속도와 로드셀에 의해 장력을 검출하고 장력을 발생하는 하드웨어 구성방법을 연구하는 것이다. 본 연구는 현수형 와이어 로프(Catenary Rope)의 동적 모델링을 작성한다. 이 시스템에 대하여 교류서보 전동기를 이용한 장력 발생장치를 모델링한다. 현수형 시스템의 장력 계측 장치는 하중 변환기(load cell)를 사용하고 수학적 모델링을 행한다. 장력 계측 장치에 관해서 스프링 저울을 이용해 출력을 비교 검토한 결과, 인장력을 계측하는 장치로서의 유효성을 확인하였다.