• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.9-14
• /
• 2009

The effects of post-annealing temperature on the optical and electrical properties of P-doped ZnO thin films grown on sapphire substrate have been investigated under oxygen ambient. The XRD shows that regardless of the post-annealing temperature, all P-doped ZnO thin films indicate the c-axis orientation. The results of hall effect measurements indicate the P-doped ZnO thin film annealed at $850^{\circ}C$ exhibits p-type behavior with hole concentration of $1.18{\times}1016cm^{-3}$ and hole mobility of $0.96cm^2/Vs$. The low-temperature (10K) Photoluminescence results reveal that the peak related to the neutral-acceptor exciton (A0X), free electrons to neutral acceptor (FA) and donor acceptor pair (DAP) at 3.351ev, 3.283eV and 3.201eV are observed in the films showing p-type behavior with acceptor. The optimization of deposition and post-annealing conditions will certainly make the P-doped ZnO thin films promising materials for the application to the next generation of optical devices.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.6
• /
• pp.282-288
• /
• 2017

In this paper, GaAs/AlGaAs multi-layer structure was grown by liquid phase epitaxy with graphite sliding boat, which can be used as a device structure of a photocathode image sensor. The multi-layer structure was grown on an n-type GaAs substrate in the sequence as follows: GaAs buffer layer, Zn-doped p-type AlGaAs layer as etching stop layer, Zn-doped p-type GaAs layer, and Zn-doped p-type AlGaAs layer. The Characteristics of GaAs/AlGaAs structures were analyzed by using scanning electron microscope (SEM), secondary ion mass spectrometer (SIMS) and hall measurement. The SEM images shows that the p-AlGaAs/p-GaAs/p-AlGaAs multi-layer structure was grown with a mirror-like surface on a whole ($1.25mm{\times}25mm$) substrate. The Al composition in the AlGaAs layer was approximately 80 %. Also, it was confirmed that the free carrier concentration in the p-GaAs layer can be adjusted to the range of $8{\times}10^{18}/cm^2$ by hall measurement. In the result, it is expected that the p-AlGaAs/p-GaAs/p-AlGaAs multi-layer structure grown by the LPE can be used as a device structure of a photoelectric cathode image sensor.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.9 s.339
• /
• pp.9-18
• /
• 2005

To make high-performance, low-power transistors beyond the technology node of 60 nm complementary metal-oxide-semiconductor field-effect transistors(C-MOSFETs) possible, the effect of electron mobility of the thickness of strained Si grown on a relaxed SiGe/SiO2/Si was investigated from the viewpoint of mobility enhancement via two approaches. First the parameters for the inter-valley phonon scattering model were optimized. Second, theoretical calculation of the electronic states of the two-fold and four-fold valleys in the strained Si inversion layer were performed, including such characteristics as the energy band diagrams, electron populations, electron concentrations, phonon scattering rate, and phonon-limited electron mobility. The electron mobility in an silicon germanium on insulator(SGOI) n-MOSFET was observed to be about 1.5 to 1.7 times higher than that of a conventional silicon on insulator(SOI) n-MOSFET over the whole range of Si thickness in the SOI structure. This trend was good consistent with our experimental results. In Particular, it was observed that when the strained Si thickness was decreased below 10 nm, the phonon-limited electron mobility in an SGOI n-MOSFT with a Si channel thickness of less than 6 nm differed significantly from that of the conventional SOI n-MOSFET. It can be attributed this difference that some electrons in the strained SGOI n-MOSFET inversion layer tunnelled into the SiGe layer, whereas carrier confinement occurred in the conventional SOI n-MOSFET. In addition, we confirmed that in the Si thickness range of from 10 nm to 3 nm the Phonon-limited electron mobility in an SGOI n-MOSFET was governed by the inter-valley Phonon scattering rate. This result indicates that a fully depleted C-MOSFET with a channel length of less than 15 m should be fabricated on an strained Si SGOI structure in order to obtain a higher drain current.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.671-677
• /
• 2001

A RuO$_2$ Schottky photo-detector was designed and fabricated with GaN layers on the sapphire substrate. For good absorption of UV light, an epitaxial structure with undoped GaN(0.5 ${\mu}{\textrm}{m}$)/n￣-GaN(0.1${\mu}{\textrm}{m}$)/n＋-GaN(1.5${\mu}{\textrm}{m}$) was grown by MOCVD. The structure had the carrier concentrations of 3.8$\times$10$^{18}$ cm￣$^3$, the mobility of 283$\textrm{cm}^2$/V.s. After ECR etching process for mesa structure with the diameter of about 500${\mu}{\textrm}{m}$, Al ohmic contact was formed on GaN layer. After proper passivation between the contacts with Si$_3$/N$_4$, was formed on undoped GaN layer. The fabricated Schottky diode had a specific contact resistance of 1.15$\times$10$^{-5}$ ［$\Omega$.$\textrm{cm}^2$］. It has a low leakage current of 305 pA at -5 V, which was attributed by stable characteristics of RuO$_2$ Schottky contact. In optical measurement, it showed the high UV to visible extinction ratio of 10$^{5}$ and very high responsivity of 0.23 A/W at the wavelength of 365nm.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.1
• /
• pp.6-13
• /
• 2010

In this study, Ga-doped ZnO (GZO) thin films have been fabricated on Eagle 2000 glass substrates at various substrate temperatures $100{\sim}400^{\circ}C$ and thin film thickness by RF magnetron sputtering in order to investigate the structural, electrical, and optical properties of the GZO thin films. It is observed that all the thin films exhibit c-axis orientation and a (002) diffraction peak only. The GZO thin films, which were deposited at $T=300^{\circ}C$ and 400 nm, shows the highest (002) orientation, and the full width at half maximum (FWHM) of the (002) diffraction peak is $0.4^{\circ}$. AFM analysis shows that the formation of relatively smooth thin films are obtained. The lowest resistivity ($8.01{\times}10^{-4}\;{\Omega}cm$) and the highest carrier concentration ($3.59{\times}10^{20}\;cm^{-3}$) are obtained in the GZO thin films deposited at $T=300^{\circ}C$ and 400 nm. The optical transmittance in the visible region is approximately 80 %, regardless of process conditions. The optical band-gap shows the slight blue-shift with increase in doping which can be explained by the Burstein-Moss effect.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.40-45
• /
• 2008

We present the effect of Ga-doping on the electrical, structural and optical properties of ZnO layers with a thickness of ${\sim}500nm$ deposited on glass substrates. Polycrystalline ZnO and Ga-doped ZnO (GZO) layers were deposited by radio frequency (rf) magnetron sputtering at room temperature. Based on the X-ray diffraction (XRD) and transmission electron microscopy (TEM) data, the crystalline quality of Ga-doped ZnO film was improved and GZO film has a preferred orientation along with the (002) crystal direction. The transmittance of the GZO film was enhanced by 10% in the visible region from that of the ZnO film. From photoluminescence (PL) data, the ratio of intensity of near band edge (NBE) emission to deep level (DL) emission was as high as 2.65:1 and 1.27:1 in the GZO and ZnO films, respectively. The res istivities of GZO and ZnO films were measured to be 1.27 and 1.61 $\Omega{\cdot}cm$, respectively. The carrier concentrations of ZnO and GZO film were approximately 1018 and 1020 $cm^2$/Vs, respectively. Based on our experimental results, the Ga-doping improves the electrical, structural and optical properties of ZnO film with potential application.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.119-120
• /
• 2011

Kawazoe는 1997년 p-type TOS를 만들기 위해서는 3가지가 충족되어야 한다고 언급한바 있다. 첫 번째, 가시광영역에서 투명하기 위해서 cation의 d10s0이 가득 차야 한다. 가득 차지 않은 d10 shell은 광 흡수가 가능하여 투과도를 떨어뜨린다. N-type을 예로 들어 ZnO, TiO, In2O3가 각각 Zn2+, Ti4+, In3+가 되어 d shell을 가득 차게 만드는 것을 볼 수 있다. 두 번째, cation d10s0 shell은 산소의 2p shell과 overlap 되어야 한다. 이 valence band는 홀 전도를 더욱 좋게 한다. 예를 들어 Cu1+(3d), Ag1+(4d)가 해당한다. 세 번째로, 양이온과 산소간의 공유결합을 강하게 하기 위해서 결정학적 구조는 매우 중요하다. Delafossite 구조는 산소가 pseudo-tetrahedral 구조로서 공유결합에 유리하다. 이러한 환경은 O2- (2p6)을 형성하고 홀의 이동도를 증가시킨다. 예를 들어 Cu2O의 경우 앞의 2가지를 만족시키지만 광학적 특성에서 좋지 않다. 그 이유가 3번째 언급한 결정학적인 요인에 있다. 결정 계의 환경은 Cu2O를 따라가면서 3차원적인 연결을 2차원적으로 변형된 delafossite 구조에서는 quantum well이 형성되어 band gap이 커진다. 본 연구에서는 전기적 이방성을 가지고 있는 delafossite CuCrO2 상에서 우선배향을 일으키는 인자 중 기판을 변화시켜 실험을 진행하였다. 결과적으로 기판변화를 통해 우선배향조절이 가능하였으며 CuCrO2 박막을 시켰으며, 결정방향에 따른 전기적 물성의 이방성에 관한 연구는 계속 진행 중에 있다. c-plane sapphire 기판위에는 [00l]로 성장하는 반면, c-plane STO 기판 위에는 [015] 방향으로 성장하는 것을 확인하였다. 이러한 원인은 기판과 증착되는 박막간의 mismatch를 최소화 하여 strain을 줄이고, 계면에서의 Broken boning 수를 줄여 계면에너지를 낮추는 방법이기 때문일 것으로 예상된다. C-plane sapphire 기판위에 증착될 경우 증착온도가 증가함에 따라 c-축으로의 성장이 온전해지며 이에 따라 캐리어농도의 감소와 모빌리티의 증가가 급격하게 변하는 것을 확인할 수 있다. 반면 c-plane STO 기판에서는 증착온도에 따른 박막의 배향변화가 없으며 전기적 물성 변화 또한 비교적 작은 것을 간접적으로 확인하였다.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.991-997
• /
• 2003

The effect of A1$_4$C$_3$ additive on the thermoelectric properties of SiC ceramics were studied. Porous SiC ceramics with 47∼59% relative density were fabricated by sintering the pressed $\alpha$-SiC powder compacts with A1$_4$C$_3$at 2100∼220$0^{\circ}C$ for 3 h in Ar atmosphere. Crystalline phases of the sintered bodies were identified by powder X-Ray Diffraction (XRD) and their microstructures were observed with a Scanning Electron Microscope (SEM). In the case of A1$_4$C$_3$ addition, the phase transformation of 6H-SiC to 4H-SiC could be observed during sintering. The Seebeck coefficient and electrical conductivity were measured at 550∼95$0^{\circ}C$ in Ar atmosphere. In the case of undoped specimens, the Seebeck coefficients were positive (p-type semiconducting) possibly due to a dominant effect of the acceptor impurities (Al, Fe) contained in the starting powder and electrical conductivity increased as increasing sintering temperature. Electrical conductivity of A1$_4$C$_3$doped specimen is larger than that of undoped specimen under the same condition, which might be due to the reverse phase transformation and increasing of carrier density. And the Seebeck coefficient of A1$_4$C$_3$ doped specimen is also larger than that of undoped specimen. The density of specimen, the amount of addition and sintering atmosphere had significant effects on the thermoelectric property.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.7
• /
• pp.486-493
• /
• 2003

Schottky type A $l_{0.33}$G $a_{0.67}$N ultraviolet photodetectors were fabricated on the MOCVD grown AlGaN/ $n^{＋}$-GaN and AlGaN/AlGaN interlayer/ $n^{＋}$-GaN structures. The grown layers have the carrier concentrations of -$10^{18}$, and the mobilities were 236 and 269 $\textrm{cm}^2$/V.s, respectively. After mesa etching by ICP etching system, the Si3N4 layer was deposited for passivation between the contacts and Ti/AL/Ni/Au and Pt were deposited for ohmic and Schottky contact, respectively. The fabricated Pt/A $l_{0.33}$G $a_{0.67}$N Schottky diode revealed a leakage current of 1 nA for samples with interlayer and 0.1$\mu\textrm{A}$ for samples without interlayer at a reverse bias of -5 V. In optical measurement, the Pt/A $l_{0.33}$G $a_{0.67}$N diode with interlayer showed a cut-off wavelength of 300 nm, a prominent responsivity of 0.15 A/W at 280 nm and a UV-visible extinction ratio of 1.5x$10^4./TEX>.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.5
• /
• pp.61-66
• /
• 2013

In this paper, temperature dependence of matching characteristics of $Si_3N_4$ MIM capacitor was analyzed in depth. The matching characteristics becomes worse as the temperature increases. That is, the matching coefficient of $Si_3N_4$ MIM capacitor at $25^{\circ}C$, $75^{\circ}C$, and $125^{\circ}C$ was 0.5870, 0.6151, and $0.7861%{\mu}m$, respectively. This phenomena is believed to be due to the reduction of the carrier mobility and the increase of the charge concentration of the inner capacitor at greater temperature. Therefore, the analysis of the matching characteristics of $Si_3N_4$ MIM capacitors at high temperatures is essential for application to analog and SoC (System on Chip) circuit.