• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1061-1066
• /
• 2011

In this study, the flow characteristics of an injection nozzle installed in a high-pressure holder for improving productivity were determined. The inlet velocity, nozzle inflow angle, and nozzle outlet diameter were selected as design factors having an influence on the flow characteristics, and numerical analysis was conducted for these factors. As the inlet velocity is high and the nozzle outlet diameter is small, the pressure and velocity of the injected flow are high. In the case of the nozzle inflow angle, the variation of flow characteristics according to angle was slight, but the highest pressure and velocity were found at $15^{\circ}$. In addition, the possibility of chip elimination by the injected flow was analyzed on the basis of the numerical results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.9
• /
• pp.34-39
• /
• 2007

Serial links via backplane channels suffer from severe signal integrity problems which are normally caused by channel imperfections, such as flat loss, frequency-dependent loss, reflection, etc. Particularly, the frequency-dependent loss causes ISI(Inter-Symbol-Interference) at signal waveforms. Therefore, adaptive equalizing techniques have been exploited in many products to facilitate the ISI problem. In this paper, we present an analog adaptive equalizer circuit designed in a $0.18{\mu}m$ CMOS process. It achieves 10Gb/s data transmission through a long 34-inch backplane channel(or transmission line). The post-layout simulations demonstrate $8ps_{p-p}$ jitter with 10mW power dissipation. The core of the adaptive equalizer occupies the area of $0.56mm^2$.

• Korean Journal of Optics and Photonics
• /
• v.24 no.2
• /
• pp.64-70
• /
• 2013

In this paper, two white light emitting diodes(LEDs) were manufactured by using two kinds of yellow phosphor, YAG:Ce and $(Sr,Ba)_2SiO_4:Eu$, and their spectroscopic properties were compared and analyzed. We found that the asymmetric double sigmoidal function can be applied to both white LEDs to obtain the center wavelength, the half width, and the skewness parameters. According to this analysis, the half width of the emitting spectrum of silicate phosphor was smaller than that of YAG phosphor, indicating smaller color rendering index. However, the silicate phosphor exhibited better color stability depending on the driving current than the YAG phosphor. The current dependence of the luminous efficacy of both white LEDs was investigated, which showed that efficacy decreased monotonically with current. The efficacy of the silicate-based white LED was lower than that of the YAG-based LED by about 10~12 lm/W.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.8
• /
• pp.610-618
• /
• 2017

This paper presents a 868/915 MHz CMOS RF transceiver for the ZigBee application. Using a switchless matching network, the off chip switch is removed to achieve the low cost RF transceiver, and by the elimination of the switch's insertion loss we can achieve the benefits for the RF receiver's noise figure and transmitter's power efficiency at the given output power. The receiver is composed of low-noise amplifier, mixer, and baseband analog(BBA) circuit. The transmitter is composed of BBA, mixer, and driver amplifier. And, the integer N type frequency synthesizer is designed. The proposed ZigBee RF full transceiver is implemented on the $0.18{\mu}m$ CMOS technology. Measurement results show that the maximum gain and the noise figure of the receiver are 97.6 dB and 6.8 dB, respectively. The receiver consumes 32 mA in the receiver mode and the transmitter 33 mA in the transmission mode.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.604-610
• /
• 1989

This paper is concerned with the machinability of fine ceramics(Al$_{2}$O$_{3}$) by using sintered diamond tools. For this purpose, ceramics cutting experiments under various cutting conditions such as cutting speed, feed rate, and others were carried out. The main results are follows : (1) During the cutting of fine ceramics, the used tools were found to be slightly chattering at cutting speed of 70m/min, and at cutting speed of higher than this I found the fine ceramics difficult to be cut. (2) When I used a tool with large nose radius, there occured a small amount of wear on the flank of the tool. However, at the early stage of fine ceramics cutting, the tools with smaller nose radii were required mainly to prevent the chipping of the ceramics. (3) When the materials were dry-cut, the appropriate cutting speel was found to be lower than 40m/min, and when the materials were dry-cut, I could cut them without any difficulty even at the speed of 70m/min, the surface roughness of ceramics cut at the speed of 70m/min was considerly fine. (4) It is generally believed that the principal cutting force is the largest in the case of steels cutting, but I found the thrust cutting force to be larger than any other cutting forces in the case of ceramics cutting.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.10
• /
• pp.6289-6295
• /
• 2014

Rework systems are the equipment used to install or remove semiconductor chips with BGA or SMD forms in printed circuit boards. The rework systems have hot air outlets. At the outlets, precise temperature control is needed to avoid heat shock. The aim of this paper was to suggest a new controller for temperature control at the hot air outlets. The suggested controller was a fuzzy PID controller. The fuzzy PID controllers were composed of TSK fuzzy rules and had outstanding ability for nonlinear systems control. This paper reports the design algorithm of fuzzy PID controllers, and the design process of the fuzzy PID controller for the temperature control of the outlets. Temperature control experiments were performed to verify the ability of the suggested controller. As a result, the RMS of the proposed method is 9.44 and the general method is 15.88. The experiments showed that the temperatures at the outlet using the suggested fuzzy PID controller followed the desired ones better than the commonly used PID controller.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.5
• /
• pp.927-934
• /
• 2019

Recently, mobile devices have evolved into small computers with various functions according to user requirements. Careful attention must be paid to the design of the power supply network for the stable operation of the application processor (AP), the wireless communication modem, the high performance camera, and the various interfaces of the mobile device to implement various functions of the mobile device. In this paper, we analyzed and verified the method of optimizing the design parameters such as the position, capacity, and number of decoupling capacitors to meet the target impedance required by the driver IC chip to ensure the stability of the power supply network of mobile devices that should be designed as wiring type due to mounting density limitation. The proposed wired power supply network design method can be applied to various applications including high-speed signal transmission line in addition to mobile applications.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.11
• /
• pp.61-68
• /
• 2018

This paper describes design of a 10.525 GHz self oscillating mixer semiconductor IC chip combining voltage controlled oscillator and frequency mixer using silicon CMOS technology for Doppler radar applications. The p-core type VCO included in the self oscillating mixer minimizes the noise contained in the transmitted signal. This noise minimization increases the sensing distance and acts in a direction favorable to the reaching distance and the sensitivity of the motion detection sensor. Simulation results for phase noise show that a VCO designed as a P-core has a noise characteristic of -106.008 dBc / Hz at 1 MHz offset and -140.735 dBc / Hz at 25 MHz offset compared to a VCO designed with N-core and NP-core showed excellent noise characteristics. If a self-oscillating mixer is implemented using a p-core designed VCO in this study, a motion sensor with excellent range and reach sensitivity will be produced.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.459-461
• /
• 2022

One of the big differences between Network-on-Chip (NoC) and the existing parallel processing system based on an off-chip network is that data packet routing is performed using a centralized control scheme. In such an environment, the best-effort packet routing problem becomes a real-time assignment problem in which data packet arriving time and processing time is the cost. In this paper, the Hungarian algorithm, a representative computational complexity reduction algorithm for the linear algebraic equation of the allocation problem, is implemented in the form of a hardware accelerator. As a result of logic synthesis using the TSMC 0.18um standard cell library, the area of the circuit designed through case analysis for the cost distribution is reduced by about 16% and the propagation delay of it is reduced by about 52%, compared to the circuit implementing the original operation sequence of the Hungarian algorithm.

• KSBB Journal
• /
• v.24 no.6
• /
• pp.591-597
• /
• 2009

B-type natriuretic peptide is a neurohormone secreted in the cardiac ventricles. BNP levels are elevated in patients with ventricular dysfunction. Therefore, the concentration of BNP is important factor to reflect diagnosis and prognosis for cardiovascular disease. In this respect, anti-BNP scFv is an urgent requirement for early diagnosis in the field of biosensor. Herein, the genetic codes of anti-BNP scFv were chemically synthesized and cloned into both pET22b (+) and pColdⅣ vector, respectively. The recombinant scFv was successfully expressed as a functional form in cytoplasm of E. coli and detected through Western blot and ELISA. The highest level of functional expression of anti-BNP scFv was achieved using pET22b (+) vector at $15^{\circ}C$ by addition of 0.1 mM IPTG. Additionally, being exposed to both BNP and ANP, anti-BNP scFv specifically captured only BNP. Therefore, anti-BNP scFv expressed in this study will be applied to measure the concentration of BNP as a diagnostic recognition molecule.