Daeyeon Kim;Jaemin Kim;Kwang-Ryul Koh;Sang-Bum Lee
Journal of the Korea Institute of Military Science and Technology
/
v.26
no.2
/
pp.171-178
/
2023
PCM data is result of air-vehicle flight test, this data is distributed for each engineers to analyze its condition. Since line-of-sight between the air-vehicle and the ground receiver cannot always be secured, remote PCM data recording system was claimed to be required. In this paper multi-function PCM data recorder has been described. This PCM data recorder was intended to place on inside of flight object. It can record about two hours in 32 GB SD card with maximum 7 Mbps data rate. RS-422/485 and RJ-45 interface enhanced accessibility for users. 5 V and 1 A power consumption and 19.5 mm × 152.5 mm × 102.3 mm allow to connect with mobile PCM devices. It acquired more than 190-minutes data in 12-times flight test. Also, it achieved military standard environmental test MIL-STD-810G to prove its stability and solidness.
The peptidyl prolyl sis-trans isomerase (PPIase, EC 5.2.1.8) from bacillus stearothermophilus was extracted from the cells treated with by lysozyme. PPIase was purified from the cell extracts by heat treatment, ammonium sulfate precipitation, ion exchange chromatography and finally gel filtration, sodium dodecyl sulfate polyacrylamide gel electrophoresis(SDS-PAGE). The molecular weight of the purified PPIase was estimated as 18kDa by SDS-PAGE. The 39 amino acid residues from the N-terminus were determined by the protein sequencer. The enzyme showed the optimum pH at 8.0 and was stable at the range of pH 7.0∼8.0. The enzyme was considerably stable after heat treatment at 60$\^{C}$ for 30minutes, and the enzyme was quite stable up to 65$\^{C}$. The presence of the PPIase in the refolding solution accelerated the isomerization rate of the assay peptide. PPIase gene of Bacillus stearothermophilus was screened from a genomic library by plaque hybridization using the A-l primer as a probe. A PPIase positive plaque contained a 3.0kb insert of the chromosomal DNA. A 3.0kb fragment was subcloned into pUC18, resulting pPI-40. A DNA fragment encoding the N-terminal portion of the PPIase in pPI-40 was amplified by polymerase chain reaction(PCR) method using the A-1 and B-2 primers. The amplified fragment was cloned into the Sma I site of pUC18 and recombinant plasmid was designated as pSN-18. The nucleotide sequence of 167bp fragment was determined. The deduced amino acid sequence of PPIase was completely matched with the determined N-terminal amino acid sequence of PPIase B. stearothermophilus.
The Journal of the Institute of Internet, Broadcasting and Communication
/
v.23
no.5
/
pp.131-138
/
2023
In this paper, a free space optical communication device that can be used in a mobile base station of several km or less was fabricated and its characteristics were investigated. To overcome the loss due to atmospheric transmission, an optical fiber amplifier (EDFA) with an output of 23 dBm or more was used. In order to increase the focusing speed and miniaturization of the laser beam, an optical lens was manufactured, and a transmission lens was designed to have beam divergence within the range of 1.5 to 1.8 [mrad]. A PT module that controls PAN/TILT was fabricated in order to reduce pointing errors and effective automatic alignment between transceiver devices. In this study, Reed-Solomon (RS) code was used to maintain the transmission quality above a certain level. It was manufactured to be able to communicate at a wireless distance of 300m in a weather situation with visibility of 300m. For performance measurement, it was measured using BERT and eye pattern analyzer, and it was confirmed that BER can be maintained at 2.5Gbps.
The neutron fluence measurement and evaluation technology is very important for material irradiation test. The most essential technology in this study is the neutron irradiation evaluation method using a fluence monitor. The fluence monitors were fabricated with metal wires of the purity ${\geq}$ 99.9%, whose dimensions were 0.1mm diameter, about 3 mm length, and around 150-200 ${\mu}g$ mass range. Three wire samples (Fe, Ni, Ti) were prepared for one irradiation aluminum capsule. Five capsules were irradiated in the OR5 hole of the HANARO reactor at 30 MW power for about 25 days. After irradiation tests, radiation activities were measured with the high purity germanium (HPGe) detector. The reaction rates were calculated by using the measured radiation activity data, and then neutron fluence were obtained from the reaction rates and the weighted neutron cross section with calculated neutron spectrum at the fluence monitor position.
Proceedings of the Korea Water Resources Association Conference
/
2007.05a
/
pp.2024-2028
/
2007
우리나라의 물관련 이슈는 수자원뿐만 아니라 사회, 경제 환경 등의 범위까지 확대되어 복합적이며, 기존 방법론과 기술만으로는 해결에 어려움이 있다. 따라서 새로운 기술적/방법론적 도구 개발의 필요성에 따라 통합수자원관리가 하나의 방법으로 받아들여지고 있다. 통합수자원관리는 지속가능한 수자원관리를 목표로하며, 물과 이와 관련 다양한 요소를 고려하는 통합적인 방법론이다. 그러므로 의사결정에 있어 전체론적인 접근이 필요하며, 세부적인 요소와 요소간의 연관관계를 파악하는 것이 중요하다. 이를 위하여 본 연구에서는 통합수자원관리의 기반 도구 중의 하나인 통합수자원관리 모델링 환경인 WaterRing 시범시스템을 개발하였다. WaterRing은 모델연계에 있어 필수적인 표준성, 사용편의성 및 모델공유를 제공하며, 모델코드 자체보다 모델의 개발에 많은 노력을 기울일 수 있도록 설계되었다. 따라서 수자원분야 및 다양한 분야의 모델을 연계할 수 있다. 모델의 연계를 위하여 기본모델단위를 설정하고 각각의 기본모델단위의 결합을 통하여 보다 큰 시스템으로 구성할 수 있도록 하였다. 기본모델단위는 입력/상태/출력의 세 가지 기본요소와 내부수행 루틴으로 구성되어 있다. 기본모델단위 사이의 결합을 정의하기 위하여 BPM(Business Process Management)(Arkin, 2002)와 STELLA의 모델 결합방식을 활용하였다. 기본모델단위는 독립적인 수행단위로 표준적인 입력과 출력을 수행한다. 따라서 입력과 출력의 속성이 같은 기본모델단위는 결합할 수 있다. 본 연구에서 시범적으로 개발된 수자원통합모델링환경 WaterRing은 통합수자원관리의 실현에 있어 평가, 계획에 이용될 수 있다. 그러므로 향후 시스템의 개발이 완료되면 우리나라의 통합수자원관리의 실현을 위한 기반도구로서 많은 역할이 기대된다. 홍수기에 측정된 성과를 바탕으로 고수위대의 수위-유량관계 곡선식을 개발하여야 할 것으로 판단된다. 본 연구를 통해 일부 확인된 바와 같이, 일반적인 자연하천이 아닌 감조하천의 경우는, 각각의 수위대별 유량 값의 변화가 발생하는 바 기간별 혹은 간조와 만조부를 포함하여 유량측정을 하여야 할 것으로 판단된다. 청폐화담탕(淸肺化痰湯)은 LPS로 유도된 macrophage에서 NO와 염증Cytokine 생성량을 억제하였고 murine macrophage에서 NF-${\kappa}$B 활성을 억제함으로써 iNOS와 염증Cytokine 유전자 발현을 하향조절 하였다. 이러한 청폐화담탕(淸肺化痰湯)의 항염작용으로 천식, 기관지염, 폐렴, 결핵, 산후감모 등의 호흡기 질환에 응용할 수 있으리라 사료된다.im}$5개월), 9.44${\pm}$1.05 6${\sim}$ll개월)으로 개월에 관계없이 전반적으로 유사한 비율을 나타내었다. 분획물(첨가농도 15.6 ${\mu}$g/ml)은 60%의 저해효과를 나타내면서 농도 의존적으로 그 저해효과가 컸으며 250 ${\mu}$g/ml 농도에서는 80%의 저해효과를 관찰 할 수가 있었다. 에틸아세테이트분회물의 경우 디글로로메탄 분회물에 비해 다소 낮은 저해효과를 나타내었지만 250 ${\mu}$g/ml 농도에서 약 60%의 세포독성 효과를 나타내었다. 디클로로메탄 분획물과 에틸아세테이트 분획물에 의한 면역 활성 증진 효과를 검토한 결과, 디글로로메탄 분획물은 첨가농도 1 ${\mu}$g/ml에서 94%로 Yac-1표적세포를 사멸시켰으며 에틸아세테이트 분획물도 동일 농도에서 96%의 억제효과를 나타내었다. CTLL세포를 이용
Transactions of the Korean Society of Mechanical Engineers A
/
v.29
no.5
s.236
/
pp.770-776
/
2005
The gains fur NC controller parameter are fixed when the controller is combined with a machine. However, the characteristics of controller could be changed as it has being used by the machine or other environmental conditions. Those result in that the tool positioning accuracy is influenced. The loading torque in servo motor influences on the tool positioning accuracy and it is controlled by the parameter gains. It is required to analyze the torque variation with angular positioning accuracy of the servo motor. This study focus on a measuring method and device for verifying angular positioning accuracy of NC servo motor. We used a high resolution An converter for acquiring analogue signal of rotary encoder in servo motor. The positional accuracy for a nominal tool path, which is generated by the combination of axial movements (X,Y,Z), is analyzed with the servo motor torque. The current variation signal is acquired at the power line using a hall sensor and converted to the loading torque of servo motor. The method of measurement and analysis proposed in this study will be used for determining the gains of parameter in NC controller. This gain tuning is also necessary when the controller is set up at a machine.
We have investigated output characteristics of XeCI excimer laser excited by transeverse electronbeam. We used e-beam output of 880 kV, 21 kA (70 ns, FWHM) and controlled current density of e-beam by pulsed magnetic coil (4.7 kG) which was fabricated around an e-beam diode (A-K gap is 21 mm) and laser chamber. We have obtained 35 J (4 atm) of e-beam deposition energy injected into laser media. The deposition energy was converted from an exposure area of Radcolor film and rising pressure of gas media which is measured by pressure jump method. The excited volume of $320cm^{3}$ was calculated. The maximum efficiency of 1.7% was obtained with the mixing ratio of HCllXe/Ar==0.2/ 6.3/93.5% and total pressure of 3 atm. Also laser output energy and specific energy were obtained 0.52 J and 1.7 J/I, respectively. For the analysis of experimental results we have developed computer simulation code. From the good agreements with the results of experiment and simulation we could theoretically explain the XeCI* formation channel. relaxation channel, and absorption channel of 308 nm.308 nm.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.46
no.3
/
pp.75-85
/
2009
This work proposes a 13b 100MS/s 0.13um CMOS ADC for 3G communication systems such as two-carrier W-CDMA applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs a four-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. Area-efficient high-speed high-resolution gate-bootstrapping circuits are implemented at the sampling switches of the input SHA to maintain signal linearity over the Nyquist rate even at a 1.0V supply operation. The cascode compensation technique on a low-impedance path implemented in the two-stage amplifiers of the SHA and MDAC simultaneously achieves the required operation speed and phase margin with more reduced power consumption than the Miller compensation technique. Low-glitch dynamic latches in sub-ranging flash ADCs reduce kickback-noise referred to the differential input stage of the comparator by isolating the input stage from output nodes to improve system accuracy. The proposed low-noise current and voltage references based on triple negative T.C. circuits are employed on chip with optional off-chip reference voltages. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.70LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 64.5dB and a maximum SFDR of 78.0dB at 100MS/s, respectively. The ABC with an active die area of $1.22mm^2$ consumes 42.0mW at 100MS/s and a 1.2V supply, corresponding to a FOM of 0.31pJ/conv-step.
In order to calculate dose rates from steam generators to be replaced from Kori unit 1 in 1998, radionuclide inventories inside steam generator were evaluated from smear test results and measured dose rates from S/G tubes withdrawn for the metallographical examination of damaged tubes. Based on the inventories, contact dose rates and dose rates at 1 m from the surface of a steam generator were calculated using the QAD-CG computer code. Contact dose rates ranged from 11.5 mR/hr at the bottom of channel head to 37.7 mR/hr at the middle of shell barrel, and showed no significant difference with dose rates at 1 m from the surface of steam generator. Shielding effects of lead and carbon steel were compared to provide basic shielding data. Lead shield showed excellent shielding effects. Dose rate at 1 m from the middle of S/G shell barrel decreased from 38.6 mR/hr to 15.5 mR/hr with the lead shield of 2 mm thickness. However, carbon steel showed a poor shielding effect even with the thickness of 2.0 cm. This can be explained with the great differences in the attenuation effect and buildup factor between lead and carbon steel for low energy photons.
HTML5 has developed not to have browser dependancy considering interoperability as same as maintaining compatability with lower versions of HTML. HTML5, the newest web standardization is on going of being structured. Along with the smart phone boom, HTML5 is spotlighted because it can be applied to cross platforms in mobile web environments. Specially the local Storage that has been listed in new features in HTML5 supports offline function for web application that enables web application to be run even when the mobile is not connected to 3G or wifi. With Local storage, development of server-independent web application can be possible. However Local storage stores plaintext data in it without applying any security measure and this makes the plaintext data dangerous to security threats that are already exist in other client side storages like Cookie. In the paper we propose secure Local storage methods to offer a safe way to store and retrieve data in Local storage guaranteeing its performance. Suggested functions in this paper follow localStorage standard API and use a module that provide cryptographic function. We also prove the efficiency of suggested secure Local storage based on its performance evaluation with implementation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.