• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.14.2-14.2
• /
• 2009

잉크젯의 응용이 넓어 짐에 잉크젯 헤드에서의 잉크 토출을 효과적으로 제어해야되는 이슈가 대두 되고 있다. 이를 위해서는 잉크젯 헤드의 입력전압을 적절하게 인가 해야만 한다. 본 연구에서는 잉크젯 토출 현상을 이해하고 이를 통해 잉크젯 헤드의 최적의 입력 파형을 설계가 가능한 알고리즘을 소개 하려고 한다. 본 연구에서는 토출 현상을 측정하기 위하여 CCD 카메라의 이미지를 사용한 메니스커스 운동을 측정하였다. 측정된 메니스커스 운동은 잉크젯 헤드의 피에조에 인가되는 입력전압에 의해서 야기된 압력파가 노즐에 전달되어 나타나는 현상이다. 따라서 잉크젯 헤드내의 현상 뿐만 아니라 잉크젯 토출 현상의 많은 정보를 가지고 있다. 파형 설계를 위해서 메니스커스 운동의 주기를 측정하여 잉크젯 입력 파형의 최적의 휴지시간 (dwell time)을 결정하는것이 가능하였음을 실험적으로 검증하였다. 또한 메니스커스 운동을 측정 함으로서 설계된 파형을 평가하것도 용이함을 실험적으로 보였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.536-540
• /
• 2018

As the performance of engines improves, the temperature of engines is increasing, resulting in a high piston temperature. An excessively high piston temperature may result in torque drop or engine failure. An oil jet is used to reduce the piston temperature. In this study, to monitor the effect of oil jet, a templug was used to measure the piston temperature. A templug is a kind of sensor and the hardness of the templug changes according to the piston temperature. Using a templug, the maximum temperature of the piston was measured with and without an oil jet. The piston temperature was lowered using the oil jet. The highest temperature region changed from the center crown to the front/rear area. In addition, the temperature difference between the highest and lowest regions became smaller.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.828-831
• /
• 2011

본 논문에서는 피에조 잉크젯 헤드의 액적 토출 형상에 대해 전산해석을 통하여 연구하였다. 열유체 해석 전용 프로그램인 FLUENT를 이용하여 에틸렌 글리콜이 잉크젯 헤드의 노즐에서 토출될 때의 형상을 전산모사하였다. 노즐 출구에서 메니스커스 변위의 시간에 따른 변화를 직접 측정하여 노즐 입구의 속도분포를 예측하고 이를 해석의 입력 자료로 사용하였다. 측정치와 해석치를 비교한 결과 전산해석이 측정치의 액정 형성 과정을 잘 모사함을 알 수 있었다.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10b
• /
• pp.595-597
• /
• 1999

기존의 LOD 제어방법들은 랜더링속도를 성공적으로 증가시켜왔으나 오버헤드가 크다는 단점을 갖고 있다. 이러한 오버헤드는 각 vertex마다 view-frustum clipping, back-face culling, 스크린 공간 기하학적 오차계산과 같은 view-dependent refinement criteria를 측정하고, 메쉬의 LOD를 바꾸기 위해서 edge collapse/vertex split를 수행하기 때문이다. 제안하는 방법은 메쉬를 여러 개의 region들로 나누고 vertex가 아닌 region에 대해 view-dependent refinement criteria를 측정하므로 오버헤드가 훨씬 작다. 또한 각 region 들의 LOD가 바뀔 때 미리 만들어 둔 LOD 버전들중에서 하나를 선택하기만 하면 되므로, edge collapse/vertex split을 수행하는 오버헤드는 없다. 실험적으로 제안하는 LOD 제어방법은 기존의 방법들보다 작은 메모리를 사용하고 LOD 제어 오버헤드도 적으며, LOD 제어를 하지 않은 경우보다 2배-5배의 랜더링 속도향상을 얻었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1529-1535
• /
• 2010

For the reliable use of inkjet technology as patterning tools, the jetting of the inkjet dispenser needs to be monitored for real-time detection of any malfunction. We present a self-sensing circuit that can be used to detect jetting failure by measuring electrical signals only. In addition, practical problems involved in the monitoring of inkjets in multinozzle printheads are discussed. In the study, software was developed and presented to demonstrate the feasibility of the proposed method for detecting inkjet jetting failure in a printing system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1633-1639
• /
• 1993

In spark ignition engine, EGR of lean mixture operation has advantage in emission, but disadvantages in power output and combustion flame propagation. Fast burn system is known to be a useful method to solve these disadvantages. This paper presents the characteristics of in-cylinder flow for different combustion chamber geometries, and the correlation between the in-cylinder flow and the combustion flame speed using an ion current method.

• Journal of the Korean Society of Radiology
• /
• v.12 no.3
• /
• pp.335-341
• /
• 2018

With the improvement of medical state, patients' expectations for the most advanced medical equipment are increasing. Particularly, Magnetic Resonance Image (MRI) is used as one of the core image diagnosis methods in all clinical area. However, it has been reported that many of patients who go through the examination suffer from anxiety to the severe noise level during the examination. In this study, both the noise reduction evaluation of headsets with sound-blocking materials added to existing sound-absorbing materials and the existence of sound blocking materials as artifacts on the examination image are tested. An MRI test noise is recorded as a speaker by cross-ordination the sound material (sponge) and the sound material (acrylic plate, copper plate, and 3D copper plate) inside the headset made from 3D pring. A quantitative assessment of headsets showed that the average headset value was 81.8 dB. The average dB value of the most soundproof material combination(Copper, acrylic plate, sponge, sponge) headsets on headsets with added charactering material was measured at 70.4 dB, and MRI showed that the copper was diamagnetic substance and excluded. The second most soundproof headset(Sponge, acrylic plate, 3D copper plate, sponge) was measured at 70.6 dB and MRI showed no artifacts. The same simulation of the material printed with a 3D copper PLA containing approximately 40 % copper powder resulted in no artifacts, therefore, the material output as a 3D printing was better suited for use. For MRI related research, the mutual development of 3D printing is highly anticipated.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.5
• /
• pp.357-365
• /
• 2013

In this study, forces and moments were measured on a projectile which consisted of a missile configuration body(shell) and a head installed control fins. The shell and the head were separated each other and the shell was rotated by an electric motor. The head rotated reversely against the rotational direction of the shell. The rotational force on the head was obtained from a couple of fixed fins of which angular displacement were set to the rotational direction equally. The air velocity was 40m/s on the experiment and the Reynolds number based on the diameter of head was $1.3{\times}10^5$. The other couple of fins were used to control the position and direction of the projectile by changing the angular displacement. From this experiment, the variation of force and moment were measured on the rotating projectile, and the effective amplitude and frequency were obtained through the FFT analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.1
• /
• pp.71-78
• /
• 1984

본 논문은 왕복동 내연기관의 방열에 관한 연구의 하나로서 디이젤 기관 실린더 헤드와 흡 배기 밸브의 온도 분포와 열유속의 분포를 구한 것이다. 방열 해석은 기관의 정상 작동된 다음의 실린 더 헤드의 열부하가 일정하다고 생각하여 실린더 헤드의 밸드 시이트 양단의 온도와 연소 가스 배출 온도, 흡기 및 냉각수 온도를 측정하고 온도분포 및 열유속을 유한요소법을 적용하여 구하 였다. 본 연구의 결과 실린더 헤드 및 밸브의 과부하는 밸브의 경우에는 밸브 헤드 중심과 밸브 헤드 중심 부근에서 일어나며, 실린더 헤드의 경우에는 헤드 중심부 표면에서 발생하였다. 흡 배 기 밸브 및 물재킷부의 온도 분포 및 열유속의 분포를 주어진 냉각수 온도 조건에 대하여 구한 후 이들을 비교 검토 하였다.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.54-62
• /
• 2017

The aim of this study is to find out the water spray features of in-rack sprinklers for rack storage. This study conducted cold water flow test, measurement of spray angle and densities by angles for sprinkler head manufactured by a Korean company and a U.S. company. Korean sprinkler head had a wide angle of water spary. The water spray angle of a U.S. sprinkler head was narrow compared to the Korean sprinkler. In comparison of the Korean head with U.S. head of the same K80, the Korean head can send water to parts that are difficult to directly spray, but the spraying density by angle was low. U.S. head can send more water than Korean head at a narrow angle. In conclusion, for flammable materials placed in two or more rows in a rack storage, a zigzag arrangement with face sprinklers will be effective.