• Solar Energy
• /
• v.12 no.1
• /
• pp.81-87
• /
• 1992

The purpose of this study was to investigate the fluid flow characteristics of heat storage in sensible heat storage system for use In cooling and heating of buildings. Heat storage material was gravels and experiments were performed in the condition of constant temperature. The experimental parameters were fluid velocity and size of gravels. The experimental results of the heat storage quantity and the heat storage efficiency by the variation of packing size and fluid velocity were as the follows : The maximum value of the heat storage capacity and heat storage efficiency and the minimum arriving time for maximum heat storage were observed when the packing ratio was 72.5% and the fluid velocity was 0.14m/s.

• Journal of the Korean Magnetics Society
• /
• v.11 no.2
• /
• pp.50-57
• /
• 2001

Magnetic inductive probe was designed and assembled for sensing the residual stress developed in the ferromagnetic thin sheet. The residual stress measurement system with this probe could resolve the residual stresses developed in the sheet in terms of principal stress orientation, and magnitude of the principal stress. It was consumed that the obtained probe output voltage from the qualified ferromagnetic Fe-42Ni lead frame sheet and quality-rejected sheet is effectively determined using the developed device. The lead frame sheet which has accumulated a high level of residual stress always showed a distinctive stress distribution and magnitude compared with those of qualified lead frame sheet. Those differences were well resolved as functions of input current or used frequency.

• Solar Energy
• /
• v.10 no.2
• /
• pp.38-43
• /
• 1990

The present study was to investigate the use of a phase change material for hydronic radiant floor heating. Two identical unit test cells sized $1.8m^L{\times}1.8m^W{\times}1.8m^H$ were built and installed with specially designed $1.6cm^T{\times}9cm^W{\times}80cm^H$ aluminum Ondol-panels holding 1.25kg of calcium chloride hexahydrate(CCH) each. It was found that the Ondol-panel with CCH reduced the room temperature fluctuations and maintains the phase changing temperature for considerably long duration, $2{\sim}4$ times of heating hour, over no-CCH one.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.567-574
• /
• 2011

Aluminum extruded panels are widely used instead of corrugated steel panels for weight reduction in high-speed trains. Of the layers in the train body, it makes the largest contribution to the sound insulation. However, compared with that of a flat panel with the same weight, the TL of the aluminum extruded panel is remarkably lower in the local resonance frequency band. We study aluminum extruded panels for next-generation 400-km/h trains. We investigate the problem of sound insulation and propose a practical method to improve the sound-insulation performance. The local resonance frequency region is increased by a modification of the core structure, and urethane foam is placed in the core. The effect on the sound insulation is verified by experiments. Finally, the improvement for the entire sound-transmission loss is estimated for the layered floor panels of express trains.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.9
• /
• pp.27-33
• /
• 2011

In the case of the existing method of underground pipe construction, the difficulty of the bedding compaction of pipe causes reducing the compaction efficiency and the stability of the underground facilities and conclusively damaging the structures. One of the methods to solve these problem is using the flowable fills as a backfill material. Therefore, in this study, numerical analysis of the underground pipe was performed in order to evaluate the behavior of pipe according to backfill mixtures. To estimate the deformation characteristic of the underground pipe, the displacement of the main part of the pipe, ground settlement and vertical earth pressures were measured in different backfill mixtures and maintaining the other conditions constantly. As a result of numerical analysis, using the flowable fills as the backfill material is better than using sand in reducing the ground settlement, the pipe deformation and the vertical earth pressure aspect.

• Journal of Conservation Science
• /
• v.26 no.2
• /
• pp.183-190
• /
• 2010

We fabricated urethane material based on properties of reversible and unfading for antic-ceramics restoration. This material with low viscosity was made hardness control possible that user want. And it have very strong adhesion and shear strength properties and is shown the best properties for pigment filling, anti-contractibility, coloring as like epoxy system materials. Particularly, the yellowing and ir-reversibility problem in epoxy restoration material were finally solved. So, there is guarantee in the eternity and stabilization of restoration for antic-celamics. And in order to show the reversible state of the restoration, we successfully dissolve this urethane materials in solvent after perfect restoring subsequently.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.74-81
• /
• 2019

In this study, to characterize the application of CSA and dihydrate gypsum Utilizing industrial byproducts, we investigated the characteristics of CSA and dihydrate gypsum to investigate the characteristics of Mine Liner according to the addition amount. As a result of compressive strength, length change and absorption rate of mining lime wastewater according to CSA addition amount, up to 30% of CSA showed a positive effect on shrinkage and absorption reduction effect as well as strength at initial age. However, due to excessive use of CSA 50%, it was reduced by 15% compared to OPC due to increase of absorption rate and decrease of cement amount due to over expansion rather than shrinkage compensation and void filling.

• Nuclear Medicine and Molecular Imaging
• /
• v.40 no.4
• /
• pp.228-232
• /
• 2006

Purpose: electrophilic $^{18}F(T_{1/2}=110\;min)$ radionuclide in the form of $[^{18}F]F_2$ gas is of great significance for labeling radiopharmaceuticals for positron omission tomography (PET). However, its production In high yield and with high specific radioactivity is still a challenge to overcome several problems on targetry. The aim of the present study was to develop a method suitable for the routine production of $[^{18}F]F_2$ for the electrophilic substitution reaction. Materials and Methods: The target was designed water-cooled aluminum target chamber system with a conical bore shape. Production of the elemental fluorine was carried out via the $^{18}O(p,n)^{18}F$ reaction using a two-step irradiation protocol. In the first irradiation, the target filled with highly enriched $^{18}O_2$ was irradiated with protons for $^{18}F$ production, which were adsorbed on the inner surface of target body. In the second irradiation, the mixed gas ($1%[^{19}F]F_2/Ar$) was leaded into the target chamber, fellowing a short irradiation of proton for isotopic exchange between the carrier-fluorine and the radiofluorine absorbed in the target chamber. Optimization of production was performed as the function of irradiation time, the beam current and $^{18}O_2$ loading pressure. Results: Production runs was performed under the following optimum conditions: The 1st irradiation for the nuclear reaction (15.0 bar of 97% enriched $^{18}O_2$, 13.2 MeV protons, 30 ${\mu}A$, 60-90 min irradiation), the recovery of enriched oxygen via cryogenic pumping; The 2nd irradiation for the recovery of absorbed radiofluorine (12.0 bar of 1% $[^{19}F]fluorine/argon$ gas, 13.2 MeV protons, 30 ${\mu}A$, 20-30 min irradiation) the recovery of $[^{18}F]fluorine$ for synthesis. The yield of $[^{18}F]fluorine$ at EOB (end of bombardment) was achieved around $34{\pm}6.0$ GBq (n>10). Conclusion: The production of $^{18}F$ electrophilic agent via $^{18}O(p,n)^{18}F$ reaction was much under investigation. Especially, an aluminum gas target was very advantageous for routine production of $[^{18}F]fluorine$. These results suggest the possibility to use $[^{18}F]F_2$ gas as a electrophilic substitution agent.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.221-232
• /
• 1993

In this study, the period for stabilization in the case of recycling leachate was compared and analyzed with the case of non-cycle type, using lysimeters filled with municipal organic refuse. The lysimeters were operated with various detention time. In addition, the degree of stabilization was estimated by the way of measuring the quantity of gas from landfills. As the results, the recycle of leachate, which was modified as the neutral level of pH, accelerated the biological decomposition of organics with the raped growth of anaerobic bacteria in the system, and reduced the period for the stabilization. In the case of BOD and COD in leachate, COD. which had been originality similar to BOD, had increased more rapidly than BOD as time lapsed. Moreover, the quantity of gas from the recycle reactor was larger than from the non-cycle reactor. The shorter the detention time of leachate gas, the larger the quantity of gas produced in the lysimeters.

• Korean Journal of Food Science and Technology
• /
• v.21 no.3
• /
• pp.321-325
• /
• 1989

Storage quality dried persimmons was evaluated by 5 scale scoring hedonic sensory analysis in various packaging methods and materials. Dried persimmons were deteriorated within 1 months of storage in polyethyene(PE, 0.08mm) and 1.5-2.5 months in nylon(PA/PE, 0.1mm) packages at room temperature, But those were kept good quality for 5 months of storage in PA/PE package and for 8 months in $CO_2$ or $N_2$ gas filled polyester/aluminum/casteded polypropylene(PET/Al./CPP, 0.1mm) package at $5^{\circ}C$. Dried persimmon had the best quality in water content of 37% and at humidity 75% and its shelf-life was noticialy prolonged by low temperature.