• Applied Chemistry for Engineering
• /
• v.1 no.2
• /
• pp.232-239
• /
• 1990

${\gamma}$-Glycidoxy propyl trimethoxy slilane, CTBN rubber(carboxyl terminated butadiene acrylonitrile rubber) and GMA(glycidyl methacrylate) were reacted with the surface of silica one by one in existence of TEA(triethylamine) or BPO(benzoyl peroxide). The amount of reactant was 2.5~5.8% of treated silica weight. The treated silica was mixed with epoxy resin and MTHPA(methyltetrahydrophthalic anhydride) in the range of 0~60% (wt. %) of total component. The flexural and thermal properties were tested for cured products. In filler content 35~55%, the using of silica treated with silane/rubber or silane/rubber/vinyl represented 25% higher flexural strength, 5% lower flexural modulus and 13% higher than mixing liquid rubber 3% with epoxy resin containing untreated silica.

• Polymer(Korea)
• /
• v.34 no.4
• /
• pp.346-351
• /
• 2010

The mechanical properties of polypropylene (PP) composites, especially the effects of the filler shapes on the modulus were studied. The experimental results were investigated and compared with the theoretical approaches proposed by Lee and Paul and based on Eshelby's principle, which three dimensional ellipsoids were filled as filler and analyzed in terms of aspect ratio, ${\rho}_\alpha=a_1/a_3$ and ${\rho}_\beta=a_1/a_2$. The shapes of fillers were observed by SEM and aspect ratios were statistically calculated. Young's moduli in the longitudinal and transverse directions for barium sulfate whose shape was sphere ($\rho_\alpha=\rho_\beta=1$) had the same values, as predicted values. The modulus in the $x_1$ direction for a glass fibers increased as the filler content increased, while the modulus in the $x_3$ direction was increased relatively small. Furthermore, mica was also used to investigate the effects of the primary and secondary aspect ratios on the mechanical properties.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.107-114
• /
• 2018

Korea Space Launch Vehicle (KSLV)-I flight test data and the modified 1-dimensional steady state modeling data from the critical design results of the KSLV-II liquid oxygen filling system operation are compared to validate the reliability of critical design modeling. A comparison of major flow rates and pressure values between test data and calculation results are conducted. The relative errors relative to maximum total flow rate for each cooling, filling, and replenishment mode are determined within 6.7%. Calculated pressure values at the outlet of the pump and the inlet of flow control valves are within 5.1%. The pressure at the inlet of the launch vehicle for each operation mode are within the measured pressure range.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.583-586
• /
• 2005

We propose a shelter guidance system using the PLC communication to resolve that a conventional shelter guidance light for underground space has problems. The proposed shelter guidance system is composed of a main control part, a PLC remote control part, a charging part, a sound generation part, a display part, an alarm part and a smoke sensing part.. The efficacy of the proposed system is verified by means of experimental. Experimental results are presented that show the effectiveness and the improvement of noise.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.229-234
• /
• 2012

This paper studied the effects of the content and the orientation of the disk shape fillers on the modulus of PP composites. The experimental results were compared with the theoretical calculations which included the three dimensional ellipsoids and analyzed by two aspect ratios, ${\rho}_{\alpha}=a_1/a_3$and ${\rho}_{\beta}=a_1/a_2$proposed by Lee and his researchers. Mica and talc were used as disk shape fillers in the composites. The shapes of mica and talc were observed by SEM and aspect ratios were statistically calculated. For the case of mica, the average aspect ratios were ${\rho}_{\alpha}=13.5$ and ${\rho}_{\beta}=1.8$, and for the case of talc, they were ${\rho}_{\alpha}=3.8$ and ${\rho}_{\beta}=1.4$. Also, the effects of two aspect ratios and the content of filler on the mechanical properties were studied: For 30 wt% of mica, $E_{11}$ increased up to about 2.7 times, and for the other case of talc, $E_{11}$ increased up to about 2.3 times, respectively.

• Restorative Dentistry and Endodontics
• /
• v.30 no.1
• /
• pp.31-37
• /
• 2005

The aim of this study was to evaluate the effectiveness of sealer placement in simulated root canal extensions. Forty resin blocks were attained from the Endo-training Bloc. In each block. The simulated root canal was made with $\#20$, 80taper GT file. After each block was longitudinally split into two halves, a standardized groove was prepared on one canal wall of two halves to simulate the canal extensions with various irregularities. The two halves of each block were assembled and all simulated root canals were obturated by single cone method with AH26 sealer. Four different methods of sealer placement were used: group A, $\#20$ K-file; group B, ultrasonic file; group C, lentulo spiral; group D, EZ-Fill bi-directional spiral. All obturated blocks were stored in $100\%$ humidity at $37^{\circ}C$ for 1 week, Using a low speed saw, each block was sectioned horizontally. Images of the sections were taken using a stereomicroscope at $\times$ 30 magnification and a digital camera. The amount of the sealer in the groove was evaluated using a scoring system, a higher score indicated better sealing effectiveness. The data was statistically analysed by Fisher's Exact Test. The sealing score was the lowest, specially at the middle area of canal extensions in group A, and that was statistically significant difference from other groups. In conclusion, the ultrasonic file, lentulo spiral and EZ-Fill bi-directional spiral were effective methods of sealer placement in simulated canal extensions. The K file was the least effective method, specially at the middle area of canal extensions.

• Journal of Korean Institute of Industrial Engineers
• /
• v.20 no.1
• /
• pp.3-13
• /
• 1994

The problem of selecting the optimal target values in a canning process is considered for situations where there is a linear shift in the mean of the content of a can which is assumed to be normally distributed with known variance. The target values are initial process mean, length of resetting cycle and controllable upper limit. Profit models are constructed which involve give-away, rework, and resetting costs. Methods of finding the optimal target values are presented and a nemerical example is given.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.132-136
• /
• 1973

Uniformly irradiated parallel-plate ionization chamber filled with a gas free of negative ion-forming contaminants was studied. Computer solutions for the electric field and the positive and negative charge densities at various degrees of saturation were obtained and discussed.

• KIPE Magazine
• /
• v.15 no.5
• /
• pp.47-52
• /
• 2010

최근 IT 기술의 발달로 인한 전자기기 사용의 증가와 전기자동차의 상용화로 에너지 저장 기술 및 저장의 편리성에 대한 요구가 증가하게 되었다 이에 안전하고 편리한 에너지 충전 방법을 제공하는 무선 전력전송 기술의 상용화에 관심이 집중되고 있다. 본 기고문에서는 최근의 다양한 무선 전력전송 기술 및 응용에 대하여 소개한다. 특히 자기 유도현상을 이용한 무선 전력전송 기술을 개괄하고, 자기공진 방식으로 전력을 전송하는 무선 전력전송 기술의 분류, 원리, 및 적용 사례에 대하여 소개한다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.225-226
• /
• 2022

In order to secure the practicality of services using drones, improve on-site operability, and improve the convenience of aircraft maintenance, it is necessary to develop a drone station that can be safely stored while ensuring charging performance. Therefore, a total seven points of improvement were derived through laboratory experiments after the development of the first prototype, and an improved second prototype will be developed in the future based on the preceding processes.