• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.47-53
• /
• 1999

Small compression-ignition direct injection engines have been developed as a measure to improve a fuel efficiency and reduce harmful exhaust gases. Those small engines generally employ high injection pressure increase on the spray impacting on a wall is discussed in this paper. The gas phase is modelled by the Eulerian continuum conservation equations of mass momentum energy and fuel vapour fraction. The liquid phases is modelled following the discrete droplet model approach in Lagrangian form and the droplet wall interaction is modelled as a func-tion of the velocity normal to impaction lands. The droplet distributions vapor fractions and gas flows are analyzed in various injection pres-sure cases. The penetrations of wall spray and vapor increase and the Sauter mean diameter decreases with increasing injection pressure.

• Journal of ILASS-Korea
• /
• v.29 no.2
• /
• pp.75-82
• /
• 2024

In this study, the thickness of the liquid sheet formed by a splash plate nozzle at low jet velocities was measured by the direct contact method. The spatial distribution characteristics of the sheet thickness in the radial and circumferential directions, and the effects of jet velocity and liquid viscosity were analyzed. The wavy surface was observed for low viscosity water, but not for high viscosity glycerol solutions. The sheet thickness decreased as the circumferential angle or the distance from the impinging point increased. The sheet thickness increased as the liquid viscosity increased. Comparison with the theoretical predictions for two impinging jets showed some differences from the measurement results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.16-22
• /
• 2008

The effect of two-phase spray injected into subsonic cross-flow was studied experimentally. External-mixing of two-phase spray from orifice nozzle with L/d of 3 was tested with various air-liquid ratio that ranges from 0 to 59.4%. Trajectory of spray and breakup phenomena were investigated by shadowgraph photography. Detailed spray structure was characterized in terms of SMD, droplet velocity, and volume flux using PDPA. Experimental results indicate that penetration length was increased and collision point of liquid jets approached to nozzle exit and distributions of mist-like spray were obtained by increasing air-liquid ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.3
• /
• pp.9-17
• /
• 2006

The influences of recess length of a liquid/liquid swirl coaxial injector on spray characteristics were investigated. It was revealed that the internal impinging phenomenon played an important role in the spray characteristics, such as spray angle and breakup length. Also, as the recess length increased, the mean drop size increased due to the increase of effective film thickness and mixing efficiency increased, but in the case of very deep recess length, the mixing efficiency decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.6-7
• /
• 2002

동축형 인젝터는 이미 여러 발사체에서 널리 쓰이고 있는 인젝터의 한 형태로서 또 다른 인젝터 방식인 충돌형과 비교하여 구조가 복잡한 단점이 있는 반면에 연소 현상의 불안정성에 대해 덜 민감하며 미립화와 혼합의 특성도 우수하다. 이런 동축형 인젝터는 크게 스월 방식과 shear 방식으로 나누어진다. 이중에서 스월 인젝터는 산화제와 연료의 유입구에 접선 방향의 속도를 줌으로써 conical sheet 형태의 분무장을 형성하여 미립화와 혼합을 꾀하는 방식이다. 이와 같은 스월 인젝터에서 중요한 변수 중에 하나인 recess의 변화에 대해 분무 형상과 미립화 혼합특성까지 파악해보았다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.2
• /
• pp.1-6
• /
• 2003

Triplet(FOF or OFO) injectors are commonly applied to liquid rockets which use LOX and hydrocarbon propellants. The FOF type injector has been known to have an advantage for the although to show lower combustion performance as compared by the OFO type. However, a large disparity between oxidizer and fuel orifice diameters of the FOF type injector may reduce both the combustion efficiency and stability so that as FOOF split triplet injector which splits a single oxidizer orifice into double orifices was designed. In the present study, spray characteristics of the FOOF injector were investigated and compared with those of the FOF injector undo. cold flow conditions. Mass distributions of oxidizer and fuel for both injectors were measured by using a PLLIF (Planar Liquid Laser Induced Fluorescence)technique, and each drop size was also measured by using an instantaneous photographic method. From the experimental results, we found out that FOOF shows more stable mixing efficiencies than the FOF. As for the drop size of both oxidizer and fuel, there was not a large difference between two injector types.

• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.22-34
• /
• 1997

Circumstances require improving diesel engine, and many studies have been done in constant volume chamber(CVC). Because the combustion mechanism of a diesel engine has many difficulties with non-homogeneous nature, there has been a limitation to analyzing the combustion mechanism with CVC. Studies are often given in a real engine, but also it has difficulties in modifying configuration of combustion chamber etc. To get more easy way for mote engine-like test, a rapid compression mechanism has been introduced. This study addresses to designing a rapid compression expansion machine(RCEM) driven by compressed air, and to applying it on IDI diesel combustion chamber which has a glow plug. RCEM is introduced first and its characteristics are tested, then spray/combustion characteristics of diesel spray impinging on a glow plug in RCEM combustion chamber are investigated. The results show active combustion in the system employing spray impinging on a glow plug so as to improve combustion efficiency.

• Journal of ILASS-Korea
• /
• v.4 no.4
• /
• pp.30-37
• /
• 1999

The breakup characteristics of liquid sheet formed by the liquid rocket injector has a close relation with the combustion efficiency. In this paper, basic characteristics of droplet size and velocity distribution were measured with PDPA for the Like Doublet Impinging Injector. Test variables were the angle of impact, the diameter of orifice and jet velocity. Water was used as test fluid. As a result, for impingement angle less than 90 degree, following correlations were obtained between drop size and design parameters : $D_{32}({\mu}m)=295.0{\times}V^{-0.09}\times(2\theta)^{-0.1}{\times}d^{0.072}$. For impingement angle greater than 100 degree, drop sizes were increased but eventually converged to a certain limiting value.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.9-14
• /
• 1999

The effect of operating condition was studied experimently on the characteristics of twin sprays ejected from two airblast atomizers, within the range of the mass air-fuel ratio 1.36∼3.54. Water and nitrogen gas were used as test fluids for the experiments. Spray characteristics of liquid spray were measured with measurement of mass distribution and instantaneous image of the spray cone. Experimental results show that the maximum specify of the distribution were lowered but distributed over the larger area when the ROA ratio increased, Center of mass position did not change with increasing water mass flow, Increase of the nozzle distance has an small effect on mass distribution of interaction area but distributed over the larger area. It was also conformed that the effect of interaction near central point of collision decreased with the increase of the ROA ratio on interaction area from comparison using superposition method

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.4
• /
• pp.44-54
• /
• 2018

In a spray experiment using a venturi mounted on a lean premixed LPP injector, droplets appear to have non-uniform distributions. To solve this problem, the exit angle of the venturi was changed to form a dump surface on the nozzle neck. The dump surface improved the atomization performance and minimized droplet loss while forming recirculation zone in the venturi exit. In order to solve the non-uniform spray of the injector, the flow characteristics inside the venturi and SMD of the spray are compared. Finally, an optimum venturi shape is selected to minimize the spray loss and improve the spray performance.