Journal of Advanced Marine Engineering and Technology

The Korean Society of Marine Engineering (한국마린엔지니어링학회)
권호 표지

Numerical Analysis of the Effect of Injection Pressure Variation on Impaction Spray Characteristics

분사압력변화가 충돌분무특성에 미치는 영향에 관한 수치적 고찰

  • Published : 1999.01.01
Download PDF
⟨ Previous Next ⟩

Abstract

Small compression-ignition direct injection engines have been developed as a measure to improve a fuel efficiency and reduce harmful exhaust gases. Those small engines generally employ high injection pressure increase on the spray impacting on a wall is discussed in this paper. The gas phase is modelled by the Eulerian continuum conservation equations of mass momentum energy and fuel vapour fraction. The liquid phases is modelled following the discrete droplet model approach in Lagrangian form and the droplet wall interaction is modelled as a func-tion of the velocity normal to impaction lands. The droplet distributions vapor fractions and gas flows are analyzed in various injection pres-sure cases. The penetrations of wall spray and vapor increase and the Sauter mean diameter decreases with increasing injection pressure.

Keywords

References

  1. SAE paper 980803 A common rail injection system for high speed direct injection diesel engines N, Guerrassi;P. Dupraz
  2. SEA paper 980805 A study on surrounding air flow induced by diesel sprays S. Sasaki;H. Akagawa;K. Tsujimura
  3. Transaction of the SAE v.96 no.Sect.4 Effect of high pressure injection on soot formation processess in a rapid compression machine to simulate diesel flames T. Kamimoto;H. Yokota;H. Kobayashi
  4. SAE paper 932652 2d imaging of fuel vapor concentration in a diesel spray via exciplex-based fluorescence technique C.N. Yen;T. Kamimoto;S. Kobori;H. Kosaka
  5. SAE paper 980806 Common rail fuel injection system for improvement of engine performance on heavy duty diesel engine T. Kato;T. Koyama;K. Sasaki;K. Mori;K. Mori
  6. SAE paper 900438 Analysis of fuel characteristics and combustion phenomena under high pressure fuel injection T. Minami(et al.)
  7. SAE paper 920459 Observation of high pressure fuel spray with laser light sheet method M. Nishida(et al.)
  8. SAE paper 870434 A new concept of diesel fuel injection timing and injection rate control system K. Nishizawa(et al.)
  9. SAE paper 910252 Development of new electronically controlled fuel injection system ECD-U2 for diesel engines M. Miyaki(et al.)
  10. ICLASS-82 no.9.3 Atomization of multi fuel sprays M.M.E. Watkil;O.A. Uyehara;P.S. Myers
  11. In Stratified Charge Automotive Engine Conf. I. Mech. E. Modelling of drop interactions in thick sprays and a comparison with experiment P.J. O'Rourke;F.V. Brocco
  12. SAE 860469 Effect of drop break-up on fuel sprays R.D. Reitz;R. Kiwakar
  13. In Int. Cont. on Liquid atomization and Spraying Systems ICLASS-82 Deformaiton behaviour of a liquid droplet impinging on a hot metal durface K. Araki;A. Moriyama
  14. Proc. R. Soc. Lond -A 280 The coales cence and bouncing of water drop at air/water interface O.W. Jayaratne;B.T. Mason
  15. Chemical Engineering Science v.21 The heat transfer from a hot wall to impinging water drops in the spheroidal state L.H.J. Wachters;N.A.J. Westerling
  16. KSME Journal v.10 no.4 The effect of nonorthogonal grids on spray and air flow predictions K. Park;A.P. Watkins
  17. International Journal of Heat and Fluid Flow v.17 no.4 Comparison of wall spray impaction models with experimental data on drop velocities and sizes K. Park;A.P. Watkins
  18. Journal of Automobile Engineering, I.Mech. E v.210 no.D3 An investigation of combustion chamber shapes for small automotive direct injection diesel engines employing spray impaction K. Park;A.P. Watkins
  19. Transaction of Computers in Reciprocating Engines and Gas Turbines, I.Mech.E Assessment and applicaiton of a new spray wall impaction model K. Park;A.P. Watkins
  20. SAE paper 930863 Simultaneous concentration measurement of vapour and liquid in an evaporating diesel spray M. Suzuki;K. Nishida;H. Hiroyasu