• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.4
• /
• pp.187-192
• /
• 2007

Impact on cylindrical surface caused by plunging breaking waves is investigated experimentally. The breaking waves are generated in a wave flume by decreasing the wave maker frequencies linearly and focusing the generated wave components at one specific location. The breaking wave packets are based on constant wave steepness spectrum. Three inclination angles of cylinder are applied to examine the effect of contact angle between cylinder and front surface of breaking waves. Also, the effect of cylinder diameter on pressure distribution and its peak value is investigated by adopting three cylinders with different diameters. The longitudinal location of cylinder is slightly moved in eight different points to find out a probable maximum value of impact pressure. The pressures and total force on cylinder surface are measured by piezo-electric pressure sensors and 3-components load cell with 30kHz sampling rate. The variation of peak impact pressures and forces is analyzed in terms of cylinder diameter, inclination angle and location. Also, the pressure distribution on cylindrical surface is examined. The cylinder location and surface position are more important parameters that govern the magnitude and shape of peak pressures, while the cylinder diameter and inclined angle are relatively insignificant. In a certain conditions, the impact phenomenon becomes very unstable which results in a large variation of measured valves in repeated runs.

• Explosives and Blasting
• /
• v.38 no.1
• /
• pp.23-29
• /
• 2020

The measurement technique with dynamic shock sensor was widely used in academic experiment for blasting and impact. However, most of dynamic sensors are expensive so that it needs to be protected by external housing structures or damping devices. In this study, the calibration method for dynamic shock sensor under the distortion by external structures. Hopkinson pressure bar system was adopted to measure the input acceleration to the sensor, and it was compared to the acceleration measured by accelerometer with customized damping device. Consequently, it is conclued that this method can be useful to calibrate the dynamic shock sensor under the linear distortion.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.11a
• /
• pp.263-268
• /
• 2000

원자력 압력용기의 건전성 평가 및 안전성 확보에 대한 관심은 1978년 미국 Rancho Seco 발전소에서 발생한 가압열충격 사고로 인해 크게 부각되기 시작하였다. 가압열충격(Pressurized Thermal Shock： PTS)이란 계통의 압력이 높은 상태이거나 증가중인 상태에서 급속한 냉각과 과도한 냉각이 발생하는 것을 의미한다. 이러한 냉각에 의해 원자로용기 외벽보다 내벽이 빨리 냉각되어 상당한 온도구배가 발생하고 이 온도구배에 따라 용기 내벽에 최대인장 열응력이 발생한다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.36-46
• /
• 1998

Shock-wave in a supersonic diffuser flow cannot be stable even in the given pressure ratio which remains constant over time, and oscillates around a certain time-mean position. In the present study, oscillation of a normal shock-wave in a supersonic diffuser was analyzed by a small perturbation method. Upstream pressure perturbation was applied to a supersonic diffuser flow with a normal shock-wave. Stability of shock-wave was investigated by considering the diffuser pressure recovery and frequency of the pressure perturbation. The results obtained show that a stable oscillation of weak normal shock-wave is obtainable for the flow with the Mach number over 1.74. The ratio of sound pressures downstream to upstream of the shock wave increases with increase of the Mach number. The present results agree well with other analytical and experimental results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.213-218
• /
• 2013

This paper presents are experimental investigation to figure out slamming impact pressure and flow characteristics of a wedge type structure in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact presure of free fall structure by a pressure acquisition system apply to Dewetron system. The angles between a model and the free surface are adapted $15^{\circ}$, $25^{\circ}$, $35^{\circ}$ and $45^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The impact pressure under the bottom of the model ha been appeared higher values at 15 degrees than 45 degrees, and also at P1.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.493-499
• /
• 2013

This paper presents are experimental investigation to figure out impact pressure and flow characteristics of a wedge type structure in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact pressure of free fall structure by a pressure acquisition system apply to Dewetron system. The angles between a model and the free surface are adapted $15^{\circ}$, $25^{\circ}$, $35^{\circ}$ and $45^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The impact pressure under the bottom of the model has been appeared higher values at $15^{\circ}$ than $45^{\circ}$, and also at P1.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.6
• /
• pp.20-28
• /
• 2021

High enthalpy test facilities, such as a shock tunnel, are to be operated at the specific pressure ratio according to the desired test condition. A metallic diaphragm is machined or a forced rupture device is used to open it at a specific pressure ratio. The diaphragm opening procedure takes several hundred microseconds including rupture and deformation. This process is expected to affect the test conditions. In this study, numerical simulation was performed for different materials, thicknesses, and opening ratios. And the characteristics of shock wave generation and the stagnation condition in the tube are investigated. Results show that the final opening ratio and rupturing procedure directly affect the speed of a shock wave, stagnation pressure, and test time.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.147-154
• /
• 1998

강체 충격자가 납 표적에 33m/s ∼ 141m/s의 속도로 충돌할 때의 침투특성을 연구하기 위하여 Jognson 이론식을 이용한 이론해석과 AUTODYN 코드를 이용한 수치해석 및 실험장치를 이용한 실험측정을 실시하고 그 결과들을 비교 분석하였다. 실험장치로는 가스압력식 발사장치를 설계 제작하였으며, 실험용 충격자로는 충돌부위 형상이 반구형인 반구형 충격자와 원추형인 원추형 충격자 2종류를 사용하였다. 또한, 납재료에 대한 동적 유동응력을 얻기 위하여 홉킨스 압력봉실험을 수행하였다. 침투특성에 관한 연구결과, 이론적 해석결과는 저속 충돌범위(반구형 충격자 : 53m/s, 원추형 충격자 ; 73m/s)에서 실험결과치와 93%이상 잘 일치하였으며, 수치해석결과는 전체적인 충돌속도 범위에서 반구형 충격자인 경우 73%이상, 원추형 충격자인 경우 86%이상 일치하였다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.284-289
• /
• 1996

국산 원자로 압력용기강(ASME SA508 cl.3)을 대상으로 표준 샤피충격시험편(2 mm V- notch)과 피로균열(precracked Charpy) 시험편을 제작하여 계장화(instrumented)충격시험을 실시하고, 충격시험시 하중점(load point)의 변위(displacement) 혹은 시간의 변화를 하중의 변화와 함께 측정하였다. 측정결과를 파괴현상 및 파괴역학과 연계시켜 해석하므로서, 가능한한 소량의 시험편(혹은 시험공정)을 사용하여 필요로 하는 인성평가 관련 정보를 획득할 수 있도록 시도하였다. 그 결과, 파괴과정을 나타내는 하중의 변화를 이용하여 Shear fraction 을 예측할 수 있었고, 하중의 변화와 관계된 변위로부터 Lateral expansion을 추정할 수 있었다. 피로균열 시험편 시험결과로 부터는 충격시의 항복하중, 항복변위, 최고하중 등을 획득하여 균열크기의 함수로 표시되는 시험편 Compliance 를 계산하였고, Equivalent energy 법과 J-integral 법을 적용하여 원자로 압력용기강의 탄소성 동적파괴인 성을 평가할 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.4
• /
• pp.281-286
• /
• 2007

The Navier-Stokes equations are numerically solved for a two-dimensional small nozzle with the area ratio of 1.8 between the throat and the exit. The shock structures are verified inside the nozzle and near the exit varying with the pressure ratio and the length of the diverging part, respectively. Especially the irregular patterns in the pressure distribution near the throat are analyzed based on the geometric characteristics. It is found that there are similar phenomena in the shock wave structure between the pressure ratio and the length changes. Also there exists a normal shock just between two different oblique shocks crossing each other in special cases.