• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.4
• /
• pp.71-81
• /
• 1999

We propose a new CPLD(Complexity Programmable Logic Device) technology mapping algorithm improving run-time under time constraint. In our technology mapping algorithm, a given logic equation is constructed as the DAG(Directed Acyclic Graph) type, then the DAG is reconstructed by replicating the node that outdegree is more than or equal to 2. As a result, it makes delay time and the number of CLBs, run-time to be minimized. Also, after the number of multi-level is defined and cost of each nodes is calculated, the graph is partitioned in order to fit to k that is the number of OR term within CLB. The partitioned nodes are merged through collapsing and bin packing is performed in order to fit to the number of OR term within CLB(Configurable Logic Block). In the results of experiments to MCNC circuits for logic synthesis benchmark, we can shows that proposed technology mapping algorithm reduces run-time and the number of CLBs much more than the TEMPLA.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.3
• /
• pp.27-31
• /
• 1974

The maximum principle of Pontryagin provides the celebrated method to obtain the optimum control switching time and switching points on the nuclear reactor. The control trajectories transfered from its initial state to the target state are optimized based on time optioptimal control method with the given reactor parameters and the piecewise constant input values.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10a
• /
• pp.574-576
• /
• 2004

임베디드 시스템에서 입출력에서 소모되는 전력양은 상당한 수준이다. 입출력 장치에서의 수행되는 타스크의 순서를 정하여 전체적으로 입출력 장지에서의 휴식 시간을 최대한 많이 허락하는 기법이 필요하다. 기존의 연구는 입출력 장치 소비 전력 최소화를 위한 타스크 스케줄링 문제를 단순한 지협적인 휴리스틱에 기반하여 풀었다. 본 연구는 기존의 연구에서의 방법과는 달리 최적의 해를 내는 해법을 제시한다. 구체적으로 시간 제약 조건을 가진 저전력을 위한 타스크 스케줄링 문제를 ILP (integer linear programming) 기법을 적용하는 방법을 제시한다. 본 연구는 또한, 실험을 통해 주어진 시간 안에 최적의 해를 구하는 문제의 크기를 판단하는 기준을 제시할 수 있다는 의의를 가진다.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2005.09a
• /
• pp.45-48
• /
• 2005

디스플레이 모듈에서 hot plate를 이용한 이방 전도성 필름(ACF: Anisotropic Conductive Film) 접합의 공정을 고출력 다이오드 레이저를 이용한 공정으로 대체하였다. 다이오드 레이저를 이용한 ACF 접합은 공정 시간을 기존보다 줄일 수 있으며 평탄도 및 응용성에 있어서 hot plate 공정보다 뛰어나다. 또한 다양한 샘플에도 지그 및 레이저광의 자유로운 변형으로 응용성이 매우 뛰어나다. 에너지 분포가 고른 선광을 이용하여 ACF 접합을 수행하였다. 레이저 에너지 밀도 $100\;W/cm^2$, 압력 20 kg, 레이저 조사시간 4초 이상에서 800 gf/cm 이상의 인장력을 얻을 수 있었고 기존의 공정 시간을 두 배 이상 단축하였다.

• 대한치과보철학회:학술대회논문집
• /
• 1997.11a
• /
• pp.50-50
• /
• 1997

• Journal of the Korea Computer Industry Society
• /
• v.2 no.3
• /
• pp.363-368
• /
• 2001

This paper introduced cascading technique as a new technology composed of two pulse transformers and presented the experimental data and results. To obtain the stable pulse voltage adopted cascading technique, we designed and tested a compact pulse generator by adjusting the load resistors and input voltage. Adopting cascading technique to load, we found that average cascading voltage was about 62$\%$ of theoretical value. Cascading ratio was calculated at almost 19 compared with non cascading voltage.

• The KIPS Transactions:PartC
• /
• v.12C no.1 s.97
• /
• pp.147-156
• /
• 2005

CGI is a standard interface rule between web server and gateway devised for the gateway's standard output to replace a static web document in UNIX environment. So, it is common to use standard I/O statements provided by the programming language for the CGI gateway. But the standard I/O mechanism is one of buffer strategies that are designed transparently to operating system and optimized for generic cases. This means that it nay be useful to apply another optimization to the standard I/O environment in CGI gateway. In this paper, we introduced standard output method and file output method as the two output optimization areas for CGI gateways written in C language in the UNIX/LINUX systems, and applied the proposed methods of each area to Debian LINUX, IBM AIX, SUN Solaris, Digital UNIX respectively. Then we analyzed the effect of them focused on execution time. The results were different from operating system to operating system. Compared to normal situation, the best case of standard output area showed about $10{\%}$ improvement and the worst case showed $60{\%}$ degradation in file output area where some performance improvements were expected.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.221-226
• /
• 1998

과잉온도 차온(Overtemperature $\Delta$T) 및 과잉출력 차온(Overpower $\Delta$T)트립에 쓰이는 온도 측정계통 총 지연시간은 6초로 구성되며 RTD 우회배관 제거시 4.5초의 RTD 응답시간(일차지연 상수로 가정)과 1.5초의 순수지연시간(전자회로 지연시간 + 그립퍼 풀림시간등)으로 구성된다. 그러나 RTD우회배관 제거전 사고분석을 일차지연상수를 3.5초, 순수지연을 2.5초로 모델링하였으므로 Simulink를 통한 영향분석과 Rack 응답시험 계단파 입력신호의 타당성을 평가하였다. RTD 응답시간은 전형적인 1차 지연요소로 나타내며 계전기나 제어봉 Gripper Release 시간 등은 순수 지연으로 가정하고 분석을 수행하고 기타 지연/지상 필터를 발전소와 동일하게 모델링하여 분석하므로써 발전소에서 일어나는 과도현상을 묘사할 수 있다는 점을 고려할 때 RTD우회배관 제거후 응답시간 지연상수가 바뀌더라도 안전하다는 결론에 도달했다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.8
• /
• pp.54-61
• /
• 2001

A fully on-chip open-drain CMOS output driver was designed for high bandwidth DRAMs, such that its output voltage swing was insensitive to the variations of temperature and supply voltage. An auto refresh signal was used to update the contents of the current control register, which determined the transistors to be turned-on among the six binary-weighted transistors of an output driver. Because the auto refresh signal is available in DRAM chips, the output driver of this work does not require any external signals to update the current control register. During the time interval while the update is in progress, a negative feedback loop is formed to maintain the low level output voltage ($V_OL$) to be equal to the reference voltage ($V_{OL.ref}$) which is generated by a low-voltage bandgap reference circuit. Test results showed the successful operation at the data rate up to 1Gb/s. The worst-case variations of $V_{OL.ref}$ and $V_OL$ of the proposed output driver were measured to be 2.5% and 7.5% respectively within a temperature range of $20^{\circ}C$ to $90^{\circ}C$ and a supply voltage range of 2.25V to 2.75V, while the worst-case variation of $V_OL$ of the conventional output driver was measured to be 24% at the same temperature and supply voltage ranges.

• The Journal of the Korea Contents Association
• /
• v.19 no.12
• /
• pp.517-526
• /
• 2019

The purpose of this study is to find the optimal method for clinical application by analyzing image quality and radiation output according to parameter combination when using the Automatic Exposure Control (AEC). The experimental method combines 70, 81 kVp with sensitivity S200, S400, S800 and S1000 of the Automatic Exposure Control for Entrance Surface Dose (ESD), current volume, Signal to Noise Ratio (SNR), Contrast to Noise Ratio (CNR), Time-to-Radiation Dose Curve in abdomen and pelvis. And then, image quality and radiation output stability were evaluated. As a results, Entrance Surface Dose, current volume, Signal to Noise Ratio, Contrast to Noise Ratio decreased as the tube voltage and sensitivity were set higher. In addition, the higher tube voltage and sensitivity, the Time-to-Radiation Dose Curve showed a poor output stability. In conclusion, the higher the combination of tube voltage and sensitivity in the use of Automatic Exposure Control, the more problems can be seen in image quality and stability of the radiation output. Therefore, a relatively low combination of tube voltage and sensitivity showed that the image quality and radiation output stability could be optimized by minimizing the error range that would occur when the detector recognized a combination of parameters.