• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.28-28
• /
• 1998

단일 충돌제트의 경우 충돌면에서의 열전달 효과는 제트 출구와 충돌면 사이의 간격, 노즐 형상에 따른 제트출구의 초기조건, Re$_{D}$수 변화와 충돌면의 형상이나 표면거칠기 등에 따라 변화하게 된다. 그러나 수직 충돌제트의 경우 정체영역에서의 국소적인 열전달 향상은 용이하나 반경 방향으로 열전달이 점차 감소하게 된다. 따라서 충돌면의 전반적인 열전달 향상을 위해서는 열전달이 정체점보다 상대적으로 낮은 영역에서 열전달 향상이 필요하다. 또한, 실제 적용시 충돌면의 형상이나 협소한 공간에서 노즐위치의 제약으로 인하여 충돌제트가 수직으로 분사되는 경우보다 경사진 제트가 더욱 많이 응용된다. 더욱이, 수직충돌제트가 사용되는 많은 상황에서도 주위의 다른 공기 흐름의 영향으로 인하여 실제 제트가 경사각을 갖고 분사되어진다 이러한 경사충돌제트의 중요성에도 불구하고 경사충돌제트에 대한 연구는 수직충돌제트에 대한 연구보다 상대적으로 적게 이루어져 왔다.

• Journal of the Korean Vacuum Society
• /
• v.4 no.4
• /
• pp.343-349
• /
• 1995

게데형 분자드래그펌프의 배기특성을 강구(hard sphere)분자모델과 NTC(No Time Counter)충돌 scheme을 이용한 직접모사 법의 하나인 DSMC(direct simulation Monte Carlo)방법을 이용하여 해석하였다. 해석에 사용된 모델은 높이가 일정하고, 길이가 높이의 1~3000배 사이인 이차원 채널이다. 자유분자영역으로부터 연속체 영역까지의 영역에서 최대압축비와 배기속도를 계산하였다. 계산결과 기존의 최대압축비 이론 결과는 채널내의 압력변화가 클 때는 큰 오차를 유발하는 것을 알 수 있었고, 유동방향의 기체분자의 통과확률은 채널 길이와 출구압력에 관계없이 거의 일정한 값을 갖는다는 것을 발견하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.3-3
• /
• 2000

저추진력 추력기라는 것은 추력이 수 N 정도, 노즐출구직경이 수 mm 정도의 소형추력기를 의미하며, 주로 인공위성을 비롯한 우주 비행체의 자세제어, 궤도천이 등의 목적을 위해 사용된다. 따라서, 저추진력 추력기의 일반적인 작동환경은 연속체 영역, 천이영역(transition flow regime), 희박영역(rarefied flow regime)을 모두 포함하므로, 기존의 연속체 유체역학에서 사용되는 Navier-Stokes 방정식을 사용할 수 없고, 분자들의 미시적인 움직임과 내부 에너지 분포를 고려한 Boltzmann 방정식을 이용한 해석을 수행하여야 한다.(중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.235-242
• /
• 2014

To investigate pressure distributions on the shaft surface of the air bearing, the commercial CFD software was employed to study three different nozzle geometries to improve the nozzle performance: general drill-shaped, matched cube-shaped and trimmed exit nozzles. Under the influence of stagnation point, the maximum pressure was observed at the center of shaft surface for all cases. Owing to the blocking effect of a fine gap between the shaft surface and the nozzle exit, the drill-shaped nozzle has the rapid local pressure increase near the nozzle exit corner, generating the ring vortex in the radial direction within pressure ratio of 6.92, and its pressure becomes negative in a certain range of downstream. In comparison, the contoured nozzle showed a local pressure increase in the measured range of pressure ratios, but a negative pressure appeared within the pressure ratio of about 10. The trimmed nozzle was seemed to extend the high pressure zone near the stagnation point in the radial direction substantially, and no negative pressure was appeared in the whole range. Based on these observations, it is found that trimming nozzle exit becomes more effective for improving the performance than modifying the nozzle inside contour.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.757-764
• /
• 2011

In this study, we analysed the influence of the performance and inflow flow of a radial inflow turbine with the variation of vane nozzle exit angles for a 100kW class turbine applicable in the waste heat recovery system. For this, three-dimensional CFD analysis was performed using commercial code called ANSYS Fluent 12.1. As the vane nozzle exit angle was more increased the reattachment region near blades of the vane nozzle got smaller, and also the Mach number at vane nozzle exit was observed to be 1 due to the effect of the cross section reduction. Through this study, we expect that the analysed results will be used as the design material for the composition of the turbine optimal design parameters corresponding to the target output power.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2267-2276
• /
• 1996

Twin-fluid atomization has been widely used in combustors and process industries because of its high performance and simple structure. Flow visualization and pressure measurements were conducted to investigate the effects of gas flow in twin-fluid atomization. Schlieren photographs showed that changes in atomizing gas pressure, altered the wave patterns, and the lengths of both recitrculating toroid (impinging stangnation point) nad supersonic flow region in the jet. A longer supersonic wave pattern like net-shape wqas observed as atomizing gas pressure increased. The disintegration phenomenon of liquid delivery tube. The variation of spray angles with gas pressures were obtained by visualization using laser sheet beam. Suction pressuresat the nozzle orifice exit and recirculating region are shown to be used to estimate the stable atomization condition of a twin-fluid atomizer.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.11B
• /
• pp.1030-1037
• /
• 2008

This paper presents an algorithm for the path-finding problem in unknown environments with cooperative and commutative multi-robots. To verify the algorithm, we investigate the problem of escaping through the exit of a randomly generated maze by muti-robots. For the purpose, we adopt the so called frontier cells and cell utility functions, which were used in the exploration problem for the multi-robots. For the wireless communications among the mobile robots, we modify and utilize the so called the random basket routing, a kind of hop-by-hop opportunistic routing. A mobile robot, once it finds the exit, will choose its next action, either escape immediately or stay-and-relay the exit information for the others, where the robot takes one action based on a given probability. We investigate the optimal probability that minimizes the average escaping time (out of the maze to the exit) of a mobile robot.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.25-25
• /
• 1999

안정화 화염으로 수소 확산 화염을 이용한 메탄/공기 난류 예혼합 화염의 미연가스 영역의 난류 특성을 측정하였다. 측정은 동일한 위치에 대해서 화염이 존재할 때와 존재하지 않을 때에 대해 수행되었다. 버너 출구 레이놀즈 수 7000에서 당량비 0.6과 1.0의 경우에 대해 실험이 수행되었다. 난류 유동장은 2색 레이저 유속계에 의해 측정되었다. 21개의 위치에 대해서 반복적으로 측정이 수행되었다.

• Journal of the Korean Institute of Gas
• /
• v.15 no.3
• /
• pp.53-57
• /
• 2011

The present study has been carried out to analyze the flow characteristics of a heat recovery steam generator with the change of inlet flow conditions by using numerical flow analysis. The inlet of HRSG corresponds the outlet of gas turbine exit and the flow after gas turbine has strong swirl flow and turbulence. The inlet flow condition of HRSG should be included the exit flow characteristics of gas turbine. The present numerical analysis adopted the flow analysis result of gas turbine exit flow as a inlet flow condition of HRSG analysis. The computational flow analysis result of gas turbine exit shows that the maximum axial velocity appears near circular duct wall and the maximum turbulent kinetic energy and dissipation rate exist relatively higher gradient region of axial velocity. The comparison of flow analysis will be executed with change of inlet turbulent flow condition. The first case is using the inlet turbulent properties from the result of computational analysis of gas turbine exit flow, and the second case is using the assumed turbulent intensity with the magnitude proportional to the velocity magnitude and length scale. The computational results of flow characteristics for two cases show great difference especially in the velocity field and turbulent properties. The main conclusion of the present study is that the flow inlet condition of HRSG should be included the turbulent properties for the accurate computational result of flow analysis.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.105-111
• /
• 2013

The present study has been carried out to reduce the heat loss from a built in refrigerator by using reverse heat loss method to discern the region with larger heat loss. To perform this purpose, an infrared thermographic camera has been used to measure the surface temperature of the refrigerator and tried to improve the heat loss near the ice dispenser. The numerical heat transfer analysis also has been accomplished to clarify the heat transfer mechanism near the ice dispenser. The possible applicable method to reduce heat loss was increasing the curvature radius at the ice dispenser corner. The curvature radius has been changed from 0mm to 40mm to see the effect of the curvature at the corner. From the present research, the optimal curvature radius for the reduction of heat loss at the ice dispenser could be 30mm.