• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.387-390
• /
• 2007

Recently the diameter of the 5MW wind turbine reaches 126m, and the tower height is nearly the same with the wind turbine diameter. The blade will experience periodic inflow oscillation due to blade rotation inside the ground shear flow region, that is, the inflow velocity is maximum at uppermost position and minimum at lowermost position. In this study we compare the aerodynamic data between two inflow conditions, i.e, uniform flow and normal wind profile. From the computed results all of the relative errors for oscillating amplitudes increased due to the ground shear flow effect. Especially My at hub and $F_x$, $M_y$, $M_z$ at LSS increased enormously. It turns out that the aerodynamic analysis including the ground shear flow effect must be considered for fatigue load analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.768-772
• /
• 1994

공작기계의 주축은 최근 고속화,고정밀화 및 고강성화되어가는 경향이 커지고 있다. 이러한 경향에 따라서 주축의] 설계는 매우 중요하며, 주축용 베어링은 앵귤러 콘택트 볼베어링이 많이 사용되고 있다. 공작기계의 주축은 고속 회전에 따른 고강성의 필요성이 증대하게 되고, 고상성을 얻기 위하여 축 방향의 일정한 예압을 주게된다. 이 예압량은 결국 축 방향의 하중이므로 주축용 베어링의 수명을 변화 시키게 된다. 따라서 축 방향 하중의 변화에 따른 베어링의 수명 특성을 파악하여야 하며, 적절한 베어링 수명의 판단을 통해 기계의 보수 및 관리에 관한 재경비를 절감할 수 있다. 그러므로 본 연구에서는 실험을 통해 베어링의 특성 주파수를 이끌어 내고 주파수 스펙트럼 분석을 이용하여 베어링의 상태를 진단하 는 기본겆인 데이터를 얻는다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.170-170
• /
• 2004

박막의 접착강도를 측정하기 위하여 수직력과 수평력을 동시에 측정할 수 있는 0.1∼100 N 용량의 2축 로드셀에 기반을 둔 스크레치 테스터를 개발하였다. 반도체용 Si wafer 기판 위에 Au나 Al 등의 금속이 관은 박막으로 증착된 제품을 table에 고정시킨 후, 2축 로드셀(x, z)이 장착된 하중센서의 선단에 Diamond Tip을 장착하여 기판과 박막에 하중(z-axis)을 증가시키면서 동시에 wafer를 x축 방향으로 이동시킨다. 이런 방식으로 시료의 표면을 긁으면 박막이 벗겨져 나가 Diamond Tip이 기판에 닿을 때 서로 다른 경도차에 의해 진동이 발생하게 되고, 이 진동을 Acoustic Emission 센서에서 감지하여 Crack 발생 시점의 Load와 Stroke를 찾아내게 된다.(중략)

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.409-413
• /
• 2007

To assure the structural integrity for the hub and low speed shaft (LSS) of the drive train, it is necessary to obtain the ultimate aerodynamic loads acting on the wind turbine blade. The aim of this study is to predict the time histories of 3 forces and 3 moments at the hub and the LSS based on the design load case of the IEC 61400-1. From the calculated results most of the load components have rotor revolution frequency whereas thrust and torque of the LSS show blade passage frequency. It turns out that the EWM wind condition involves the maximum ultimate loads at both hub and LSS of the horizontal axis wind turbine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.140-147
• /
• 2003

Full scale durability test in the laboratory is an essential of any fatigue life evaluation of components or structures of the automotive vehicle. Component testing is particularly important in today's highly competitive industries where the design to reduce weight and production costs must be balanced with the necessity to avoid expensive service failure. Generally, hydraulic road simulator is used to carry out the fatigue test and the vibration test. In this paper, the link unit which is able to realize the 3 element forces such as vertical force, lateral force, and longitudinal force that are applied to the road simulator is designed. Also, the designed link is verified with kinematics and inverse-kinematics. From this results, the designed factor satisfied the maximum stroke so that it satisfied the requirements for 3-axial road simulator.

• Computational Structural Engineering
• /
• v.11 no.3
• /
• pp.229-239
• /
• 1998

복합재료는 강도-무게비가 다른 재료들에 비해 훨씬 크기 때문에 부재의 좌굴문제가 대단히 중요하게 취급되며, 본 논문에서는 축방향 압축력을 받는 복합재료로 된 쉘 부재의 좌굴해석이 수행된다. 이 재료는 일반적으로 이방성 재료 특성을 나타내 보이나, 섬유들이 한 방향으로만 배치되어 있는 경우 섬유방향에 연직한 평면에서의 강도나 탄성계수들은 모두 일정한 횡 등방성 재료성질을 가진 것으로 간주할 수 있다. 9 절점 degenerate 쉘 유한요소를 사용한 선형안정해석, LUSAS 범용 프로그램을 이용한 구조해석, 그리고 고전적 쉘 좌굴방정식에 의한 해석들을 수행하였으며, 그 결과들을 서로 비교, 분석하였다. 고려된 등방성 재료나 횡 등방성 재료의 경우 모두, degenerate 유한요소해석으로 계산한 임계하중들은 고전적 이론해에 의한 결과들 보다 낮았으며, LUSAS 결과들과는 거의 같았다. 이는 degenerate 유한요소에 의한 선형안정해석 결과들이 안전측에 듬을 의미하며, 복합재료로 된 쉘 구조물의 좌굴해석에 degenerate 유한요소를 효율적으로 적용할 수 있음을 의미한다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.1
• /
• pp.51-62
• /
• 2001

In-situ stress measurement using AE (Acoustic Emission) and DRA (Deformation Rate Analysis) is usually carried out under uniaxial loading in the laboratory and it consumes delay time from drilling to testing. Therefore, it should be considered how the lateral stress and delay time influence on the test results for the in-situ stress determination. As the delay time increased, the accuracy of estimating the pre-stress decreased. The pre-stress of the specimen loaded only axially was determined within an error of less than 9% (using AE) and 4% (using DRA). And the specimen on which axial pre-stress and the confining pressure were loaded had an error of less than 17% (using AE) and 14% (using DRA). The results of AE and DRA for field specimens were very similar with each other but smaller than those of hydraulic fracturing method.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.139-146
• /
• 2003

The objective of the presented study is to develop an efficient procedure of proof load testing for existing bridges. By analytical methods, some of these bridges are not adequate to carry normal highway traffic. However, the actual load carrying capacity is often much higher than what can be determined by conventional analysis. Proof load testing can reveal the hidden strength reserve and thus verify the adequacy of the tested bridge. Proof load level required for meaningful tests should be sufficiently higher than legal load. In the state of Michigan, the legal 11-axle truck can weigh up to 685 kN. In this study, a combination of two military tanks and two Michigan 11-axle trucks was used. The proof loads were gradually increased to ensure the safety of the test. After each move, measurements were taken. For the considered bridge, stress levels were rather low compared to pre-test analysis results. This is due to incorrect material strength, structural contribution of nonstructural components such as parapets and railings, and partially fixed supports.

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.13-24
• /
• 2006

The stresses in concrete pavement systems are larger when vehicle loads are applied at pavement edges, and these large stresses significantly affect the behavior and performance of pavements. Therefore, in this study, the stress distribution and the critical stresses in concrete pavements were investigated using a finite element model when dual-wheel single-, tandem-, and tridem-axle loads were applied at pavement edges. First, the stress distribution along the longitudinal and transverse directions was analyzed, and then the effects of slab thickness, concrete elastic modulus, and foundation stiffness on the stress distribution were investigated. The effect of the tire contact pressure related to the tire print area was also studied. The location of the critical stress occurrence in concrete pavements was finally investigated. From this study, it was found that the critical concrete stress due to edge loads became larger as the concrete elastic modulus increased, the slab thickness increased, and the foundation stiffness decreased. The effect of the tire contact pressure on the critical stress was clear as the slab thickness became smaller. The critical stress location in the transverse direction was independent of the concrete elastic modulus and the foundation stiffness; however, it moved into the interior as the slab thickness increased. The critical stress location in the longitudinal direction was under the axle for single- and tandem-axle loads, but for tridem-axle loads, it tended to move under the middle axle from the outer axles as the concrete elastic modulus and/or slab thickness increased and the foundation stiffness decreased.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1082-1087
• /
• 2021

The propeller shaft has different pattern of behaviors at each static, dynamic, and transient condition to a ship shaft system due to the effects of propeller weight and eccentric thrust, which increases the potential risk of bearing failure by causing local load variations. To prevent this, the various research of the shafting system has been conducted with the emphasis on optimizing the relative slope and oil film retention between propeller shaft and stern tube bearing at quasi-static condition, mainly with respect to the Rules for the Classification of Steel Ships. However, to guarantee a stability of the shafting system, it is necessary to consider the dynamic condition including the transient state due to the sudden change in the stern wakefield during rudder turn. In this context, this study cross-validated the ef ect of propeller shaft behavior on the stern tube bearing during port turn operation, which is a typical transient condition, by using the strain gauge method and displacement sensor for 50,000 DWT medium class tanker. And it was confirmed that the propeller eccentric thrust change showing relief the load of the stern tube bearing.