• Journal of Aerospace System Engineering
• /
• v.16 no.5
• /
• pp.26-34
• /
• 2022

The propulsion system of geostationary orbiting satellites is typically used to raise the orbit into a transfer orbit, maintain the orbital position in the south/north, east/west direction in regular operation, and accumulate momentum in the south/north and east/west direction. Recently, when an electric propulsion system is used in a geostationary orbit satellite, the payload capacity can be increased by about 40% compared to a chemical propulsion system. However, despite these advantages, using an electric propulsion system has several limitations that should apply to all geostationary orbiting satellites. This paper discusses the operational constraints to consider when developing an indigenous geostationary satellite using a fully electric propulsion, radiation exposure, and control mechanism design due to unit displacement and floating ground-design. A high-voltage control unit for electric drives were analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.281-285
• /
• 2007

The flow characteristics in the thruster should be analyzed considering its geometry and the pressure ratio to estimate its performance and etc. This paper suggests the computational result of an axisymmetric real nozzle for the altitude control of a satellite to find out the application limit that the assumption of continuum mechanics holds. The steady non-reacted compressible flow field in the unstructured grid system is computed and analyzed with varying the environmental pressure (or the degree of vacuum) under the fixed pressure ratio in a real thruster of which the area ratio of exit to throat is 56. The assumption of the continuum mechanics is not approved when the environmental pressure is reduced less than $10^{-3}$ atm.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.336-339
• /
• 2011

Hot-fire test facility is one of the most important infrastructure for thruster development and evaluation. During the past three years, Korea Aerospace Research Institute (KARI) and Hanwha Corporation have successfully performed the construction of hot-fire test facility for medium-scale monopellant thruster to the maximum 200N thrust level. In general, thruster hot-firing test should be performed in vacuum conditions to simulate space environment. The hot-fire test facility is divided into three subsystems, vacuum system, propellant supply system and data measurement & control system. The goal of this facility is to extend the capability from small thruster for satellite mission to medium-scale thruster for launch vehicle and lunar mission. In this paper, the progress and overview for thruster hot-fire test facility was introduced and test results were also presented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.1
• /
• pp.42-49
• /
• 2014

Performance evaluation was carried out for the 70 N-class hydrazine thruster whose design performance had been already verified. The pulse-mode firing test was conducted for the development model thrusters with various thrust chamber diameters. Evaluation was made by the performance parameters such as specific impulse, impulse bit, and characteristic velocity, etc: specific impulse and characteristic velocity were deteriorated as the thrust chamber diameter deviates from a standard model. Consequently, it is revealed that the performance characteristics of standard model is most superior among the test models.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.191-195
• /
• 2006

It is definitely required to control dispersion of the rocket engine performance in order to accomplish the mission of a launch vehicle successfully. A performance dispersion analysis was conducted for a gas generator cycle liquid rocket engine and the required pressure drops were estimated for engine tunning. As a result, the vacuum thrust dispersion of the engine was from +9.1% to -8.7% and the mixture ratio deviated from +9.7% to -9.6% from the nominal value due to the errors of components and the engine inlet condition of propellants. The required pressure drop in the LOx line to the combustor is higher than in the fuel line for same mixture ratio change.

• Aerospace Engineering and Technology
• /
• v.6 no.2
• /
• pp.164-170
• /
• 2007

In this paper, the development results of electromechanical TVC actuation system is described in the aspect of design, analysis, manufacturing and test. The kinds of prime power for TVC actuation system is classified by the variety of propulsion system of launch vehicle. The electric power by battery is the sole candidate for prime power of TVC actuation system at the view point of feasible domestic infra technologies for the present. The characteristic analysis study is performed between electromechanical and electrohydraulic actuation system with respect to power efficiency, performance and weight efficiency. The electromechanical actuation system has superiority of power and weight efficiency according to less opportunity of power conversion process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.91-97
• /
• 2017

The KSLV-II launch complex system consists of mechanical ground support equipment(MGSE), fuel ground support equipment(FGSE), electrical ground support equipment(EGSE) and infrastructures. Compressed gas supply system, as a part of FGSE, is responsible for launch operations such as gas intake, storage, supply to launch vehicle and ground support equipments. This system consists of three primary elements such as gas storage part, control panel and controller. Automatic panels, as a part of control panel, are manufactured to operate remotely by controller. This study presents compressed gas supply system which is designed for KSLV-II and ground support equipment characteristics.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.1
• /
• pp.84-89
• /
• 2011

A Xenon Feed System (XFS) has been developed for hall-effect thruster to small satellite space-propulsion system applications. The XFS delivers low pressure gas to the Anode and Cathode of thruster head unit from a xenon storage tank. Accurate throttling of the propellant mass flow rate is independently required for each channel of the thruster head unit. The mass flow rate to each channel is controlled using the accumulator tank pressure regulation through a micron orifice and isolation valve. This paper discusses the Xenon Feed System design including the component selections, performance estimation and functional test.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.613-615
• /
• 2009

This paper is to introduce Hanwha Aerospace R&D Center's development status of TVC(Thrust Vector Control) system and control valves for Korean space launch vehicles. With the successful development of KSR-III TVC system, Hanwha have developed TVC system and RCS control valves for KSLV-I. Also, in the advance research area of KSLV-II, Hanwha have participated in LOx and fuel flow control valves and LOx shut-off valve development in the engine supply system. Based on the accumulated experiences and technologies in the aerospace key components and system development, Hanwha will make an important contribution to KSLV-II development in the future.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.76-82
• /
• 2011

The thrust axis alignment of the launch vehicle is very important because the misalignment causes the unstable attitude control and results in mission failure. Generally, optical methods such as digital theodolite and laser tracker and mechanical method such as turn table method are used to align the thrust axis. This article deals with the simple method using inclinometer based on the gravitational direction. The inclinometer indicates zero degree when that is located on the perpendicular plate to gravitational direction. This method needs two inclinometer, such as standard and alignment ones and uses the angle difference as the reference data to adjust the TVC actuator offset.