• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.3-3
• /
• 1997

미사일 수직발사 시스템은 공간을 작게 차지하고 간편하여 각국이 선호하고 있다. 그러나 수직발사 초기에는 매우 낮은 속도로 상승하므로 Fin의 공력이 발생하지 않기 때문에 추력방향을 직접제어하지 않으면 안된다. 추력방향 제어장치는 Gimbal, Jet Vane, Jet Tab, Secondary Injection 등 여러 방식이 있으나 Jet Vane Type의 추력 방향 제어장치는 응답이 빠르고 경량화가 가능하며 후방 Fin과의 연동 및 작동 후 분리가 가능하다는 장점으로 인해 수직발사 미사일의 초기 방향제어에 주로 사용한다. 이 장치는 Vane이 화염 속에서 직접 구동되므로 고내열성 재료의 기술이 필요하며 미사일의 전체 System에 요구되는 Side Force를 발생시키기 위한 Vane의 최대 받음각 및 회전속도를 결정해야 한다. 따라서 초음속 유동해석을 통해서 Vane의 받음각에 대한 Side Force와 Torque를 계산하며, 구조해석을 통해 Side Force가 가해지는 동안의 Housing의 굽힘, 비틀림 하중 등을 계산하였다. 또한 Controller는 기존의 유압방식보다도 소형이며 복잡하지 않고 가격이 싼 DC Motor와 감속기를 이용하여 빠른 응답성에 부합토록 설계하였다. 본론에서는 성능과 관련된 초기 요구조건에 대한 최적설계의 변수들을 해석하고. 그에 따른 개발사양, 개발 과정, 구조, 시험방법 등에 대해 고찰하고자 한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.19-25
• /
• 2016

Using a actuator to which the motor and the gear is applied to the I-PD control method and a dual-loop system to carry out precise position control. I-PD control algorithm performs an operation to reduce the overshoot in the transient response. Accordingly, the actuator obtains a precise position tracking result. Also it utilizes two sensors and dual loops. It reduces the adverse effect on the precise position control that may occur by the end play of the gear train. In this paper, we uses the actuator model applying the BLDC motor and gear in order to determine the position tracking result by the dynamic characteristic change. It was verified by the simulation results.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.3
• /
• pp.61-67
• /
• 2004

The extinction characteristics of the solid propellant were studied experimentally in this paper. These characteristics are required for designing TCO (thrust cut off) system of the solid rocket motor Parameters to characterize solid propellant extinction were defined by physical observation. A device was designed (or acquiring these parameters and the firing tests were implemented to get the preliminary data for the extinction characteristics of HTBP propellant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.403-406
• /
• 2009

This research is based on the altitude temperature, pressure and humidity, as defined by MIL-HDBK-310 standard and modifies this conditions to conform to the new standard MIL-STD-810F and test procedure given in AIAA-2466 from this fundamental guideline optimal design and sizing of test section, inlet, exhauster duct, temperature and humidity control was performed.

• Journal of the Korean Society for Railway
• /
• v.20 no.3
• /
• pp.339-348
• /
• 2017

Power supply for railway cars can be divided into propulsion system power supply and auxiliary power units (APU). The propulsion system power supply is for propulsion of railway cars, and regenerative braking; the APU provides power for the air compressor, lighting, car control and other auxiliary parts. According to high voltage and high current specifications, generally, an insulated-gate bipolar transistor (IGBT) is adopted for the switching component. For appropriate switching operation, a gate driver unit (GDU) is essentially required. In this paper, the technical trends of GDU for railway cars are analyzed and a design consideration for IGBT GDU is described.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.5
• /
• pp.61-70
• /
• 2017

Robust thrust distribution method of solid DACS is researched. For the case of the system which has higher number of actuation nozzles than the degree of freedom of thrust to be controlled, the robust thrust allocation law which accommodate the abnormal operation is suggested. Assuming the situation that some nozzles are uncontrollable, the error between nozzle throat area command and response can be calculated. The error is used for realtime reshaping of weighting matrix. From the weighting effect, the nozzle which operated abnormally has low responsibility for the command then, the thrust error is reduced. The suggested algorithm is verified by the simulation of abnormal operation condition of DCS and ACS nozzle respectively.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.186-192
• /
• 1998

This paper presents a high performance low switching PWM technique or the propulsion system of railway such as subway and high speed train. In order to achieve the continuous voltage control to six-step and s low harmonics with low switching frequency under 500Hz, the synchronous technique is combined with a space vector overmodulation and implemented by using DSP. Improved performance and a validation of proposed method are showed by the digital simulation and the experimental results using a 1.65MVA IGBT VVVF inverter and inertia load equivalent to 160 tons railway cars.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.35-35
• /
• 1999

최근 미사일 및 차세대 비행체에는 초기 고기동이나 무수한 제어력의 특성을 지닌 TVC 시스템이 많이 사용되고 있다. 기존의 공력 조타에 의한 비행 자세 제어방법은 속도의 2승에 비례하는 제어력을 발생하지만, TVC(Thrust Vector Control)를 이용하면 추력 방향을 변경하여 제어력을 얻음으로써 방향 제어에 보다 월등한 성능을 발휘할 수 있기 때문이다. TVC를 이용한 방향제어는 저속도 경우와 공기가 희박한 고 고도에서도 충분한 제어력을 얻을 수 있다. 그러나 그 우수성에 비추어 국내에서는 아직 그 성능에 대해 충분한 자료가 없는 실정이다.

• ICROS
• /
• v.3 no.3
• /
• pp.29-35
• /
• 1997

본 논문에서는 인공위성의 자세를 측정하는 장치로서 태양센서, 지구수평센서, 자이로스코프, 별센서, 자장계 등의 자세감지장치와 궤도조정 및 자세제어를 하기 위한 모멘텀 휠, 반작용 휠, 가스 제트 추력기 등 각종 구동장치의 기술적 특성에 대해서 검토하고자 한다. 본 논문의 주목적은 최근 국내에서 활발히 추진되고 있는 인공위성 개발 사업 관련 위성체와 관련된 일반의 관심을 증대시키고 관련 실무 지식을 소개하고자 하는데 있다.

• Journal of KIISE:Computing Practices and Letters
• /
• v.9 no.6
• /
• pp.674-682
• /
• 2003

Ship autonomous navigation is designated as what computerizes mental faculties possessed of navigation experts, which are building navigation plans, grasping the situation, forecasting the fluctuation, and coping with the situation. An autonomous navigation system, which consists of several subsystems such as navigation system, a collision avoidance system, several data fusion systems, and a motion control system, is based on an intelligent control architecture for the sake of integrating the systems. The motion control system, which is one of the most essential system in autonomous navigation system, controls its propulsion and steering gears to move the ship satisfying its hydrodynamic characteristics. This paper is the study on the ship movement control system and its implementation which are totally developed and run on virtual-world system. Receiving the high-level control values such as a waypoint presented from the collision avoidance system, the motion control system generates them to low-level control values for propulsion and steering devices. In the paper, we develop a ship motion controller using Oldenburger's theory based on mathematical fundamentals, and simulate it with various scenarios in order to verify its performance.