• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.80-89
• /
• 1998

Propulsion subsystem transfers KOMPSAT into mission orbit and controls its attitude. Design factor consists of structure safety, electrical circuit design, consumable power estimation of thermal hardwares, damping device design of fuel transient pressure, and system configuration design by considering plume effect from thruster firing. System level analysis should be performed for verification of system design under launch vehicle and orbital environment. Electrical functional test of thermal control hardware, proof pressure test, cleanliness verification test, and internal/external leakage test of fuel feeding system should be carried out for performance estimation of propulsion system. Design and assembly process of propulsion subsystem was depicted and reliability of system was verified by test analysis in this paper.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.9-9
• /
• 1998

다목적 실용위성의 궤도전이 및 위성체 자세제어를 위한 추진시스템의 설계요소에는 구조적 안전성, 우주환경에서의 열제어를 위한 회로 및 구성하드웨어 설계, 연료계통 맥압강하를 위한 장치설계 및 추력기 배기가스 영향을 고려한 형상설계 등이 있으며, 설계검증을 위해 부분해석이 수행된다. 또한 발사환경과 우주 궤도환경에서의 추진시스템 성능평가를 위한 연제어계 기능시험, 압력인증시험, 청정도시험 및 내부/외부 누설시험이 수행된다. 본 논문에서는 추진시스템 설계 및 조립공정에 대해 기술하였고, 시험분석을 통해 시스템의 설계 및 조립공정상의 신뢰성을 검증 분석하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.797-800
• /
• 2011

For the space launch vehicle, propulsion system is the most important subsystem among others. For the evaluation of development level for rocket engine, integrated system test performed in appropriate facility is needed. In this study, test article and major parameters for certifying the propulsion system of launch vehicle were reviewed.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.133-142
• /
• 2010

Propulsion system of launch vehicle is composed with subsystems as propellant tank, pressurization system, propellant fill/drain system, valve operating system, purge system and so on. Among others, pressurization system is the most important subsystem, because of the real-time control part for pressure control of propellant tank. Therefore, it is the subsystem that must be primarily considered on conceptual design process. In this paper, the data of the previously developed pressurization systems were collected and the optimum configuration was selected by analysis of advantage and disadvantage of the systems.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.55-64
• /
• 2002

A conceptual design of propulsion system for a geosynchronous communication satellite with 12 years design life is presented in this paper. Propellant mass budget for the design life is calculated using total velocity increment (ΔV) flowed-down from mission requirement analysis. Sizes of the fuel and oxidizer tank are derived based on the calculated propellant mass budget, and mass of the pressurant as well as the size and pressure of pressurant tank are calculated too. Thruster positioning, number of rocket engines, and position of tank are determined through Trade-Off Study with Structure & Mechanical Subsystem. Propulsion system configuration and its schematics are presented finally.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.1
• /
• pp.117-124
• /
• 2003

Thermal design fur satellite propulsion system has been performed. Overall design requirements and the constitution for propulsion system is described. To meet the thermal design requirements, both a primary and a redundant heater circuit, each with two thermostats placed in series, will protect each hydrazine-wetted components, even if one heater circuit fails to operate. Heater power is turned off if any one of these thermostats is opened at its higher setpoint. Thus, even if one thermostat is failed closed, the second thermostat will turn off the heater. All such components shall be insulated with MLI. Propulsion heater sizing based on the constant worst cold case condition is conducted through thermal analysis. All heaters selected fur propulsion components operate to prevent propellant freezing satisfying the thermal requirements for the propulsion subsystem over the worst case average voltage, i.e. 25 volts.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.4
• /
• pp.98-106
• /
• 2000

A conceptual design of propulsion system for a geosynchronous communication satellite with 12 years design life is presented in this paper. Propellant mass budget for the design life is calculated using total velocity increment ($\Delta$V) flowed-down from mission requirement analysis. Sizes of the fuel and oxidizer tank are derived based on the calculated propellant mass budget, and mass of the pressurant as well as the size and Pressure of pressurant tank are calculated too. Thruster positioning, number of rocket engines, and position of tank are determined through trade-off study with Structure & Mechanical Subsystem. Propulsion system configuration and its schematics are presented finally.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.76-83
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including main and rotary ducts, the nozzle subsystem including main and tip jet nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. Transient simulation performance utilized the ICV (Inter-component volume) method and simulated using the SIMULINK. Transient performance analysis was performed on 3 cases. Fuel flow schedules to accelerate from Idle to maximum rotational speed were divided into the step increase of the most severe case and ramp increase cases to avoid the overshoot of turbine inlet temperature, and variations of thrust and the turbine inlet temperature were investigated in some transient analysis cases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.712-721
• /
• 2015

Pulse Detonation Engine (PDE) has been considered as a future propulsion system for broad range of operation and higher thermal efficiency. Various subsystem technologies have been studied for more than decade to improve the performance of the potential system. New valve systems has been developed for the stable operation at high frequency including inflow-driven valve, rotary valve and valveless system. To foster the detonation initiation with a little ignition energy, plasma ignition method and DDT (deflagration to detonation transition) acceleration method such as swept ramp mechanism have been studied. Fluidic nozzle system and other nozzle system are the ongoing research topics to maximize the propulsion performance of the PDE. Present paper introduces the state of the art of PDE subsystem technologies developed in recent years.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.293-298
• /
• 2005

Air-Launching is an effective method that can launch the 'Nanosat' with low launching cost. In this study, system and subsystem design of the air launching rocket for nanosats which perform a simple mission, have been performed. Foe this purpose, the WBS of the Air-launching Rocket System, and the subsystem schematics have been defined first. Based on these results, detailed configuration and DMU have been developed.