• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.32-41
• /
• 2006

In this study, the thrust generation by simultaneous flapping airfoils in tandem configuration is parametrically studied with respect to flapping frequency, amplitude and relative location. Navier-Stokes solver with overset grid topology is employed to calculate the unsteady flowfields. The computation results indicate that when the two airfoils stroke in-phase - flapping phase lag is zero - the maximum propulsive efficiency and thrust can be obtained for most frequency and amplitude range. At a flapping amplitude of 0.2 chord and a reduced frequency of 0.75, the propulsive efficiency of aft airfoil is enhanced by about 37 % compared with that of forward airfoil. However, if flapping frequency exceeds some critical value, the strength of the leading edge vortex of aft airfoil is fortified by the trailing edge vortex of the forward airfoil, resulting in poor propulsive efficiency. It is also found that out-of-phase flapping has relatively low propulsive efficiency and thrust since vortical wake of the forward airfoil interacts with the leading edge vortex of aft airfoil in the unfavorable fashion. The total thrust and propulsive efficiency are shown to decrease with the horizontal miss distance of the aft airfoil. On the contrary, the vertical miss distance has little effect on the overall aerodynamic performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.68-75
• /
• 2015

In this paper, unsteady characteristics of pressure in solid rocket motor were analyzed by using response of pintle actuation, pressure and thrust data from ground test. Pressure and thrust in solid rocket motor can be controlled in real time by varying nozzle throat area with pintle, installed in the valve. Unsteady characteristics of pressure can be observed in this system occurred by various reasons. Two critical reasons, error of pintle actuation and ablation of center tube, are found and effects of each reason can be analyzed individually by re-prediction of pressure with response of pintle actuation and analyzing thrust to pressure ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.139-143
• /
• 2007

The overall results of combustion tests performed for a 30 tonf-class full-scale combustion chambers of a liquid rocket engine were described. The combustion chambers have chamber pressure of 53${\sim}$60 bar and propellant mass flow rate of 89 kg/so The combustion chamber is composed of mixing head, SUS baffle, baffle injector, ablative chamber, channel cooling chamber and regenerative cooling chamber. The test results show that the combustion characteristic velocity is in the range of 1673${\sim}$1730 m/sec and the specific impulse of the combustion chamber is in the range of 254${\sim}$263 sec. As the recess number of the injectors increases, the combustion characteristic velocity increases. And as the combustion characteristic velocity increases, the specific impulse of the combustion chamber also increases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.585-589
• /
• 2010

It is important for the liquid rocket engine to meet the exact performance requirements in order to guarantee the successful mission of the launch vehicle. Usually, a ground combustion test for the engine is conducted to reduce the performance error and for the tuning. For the gas-generator (GG) cycle engine, this adjustment process can be easily tuned by means of the control valves. A linearized correlation between the process parameters of the control - the combustion chamber pressure and the mixture ratio of engine - and the independent parameter of the control- rotational angle of the control valve - could be suitable to reduce the tuning errors. Also this linearity can reduce the effort for the tuning and make the process more explicit by ensuring a more intuitive control. In this point, we proposed an algorithm in the frame of the in-house-developed program to obtain the control valves' inherent characteristics which satisfy the linearity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.124-131
• /
• 2019

A design study of gas turbine engine simulation duct was conducted to investigate the operating characteristics and control gain tunning of the Altitude Engine Test Facility(AETF). The simulation duct design involved testing variable spike nozzle and ISO standard choking nozzle to verify the measurements such as mass flow rate and thrust. The simulation duct air flow area was designed to satisfy Ma 0.4 at the aerodynamic interface plane(AIP) at engine design condition. The test conditions for verifying the AETF controls and measurement devices were deduced from 1D analysis and CFD calculation results. The spike-cone driving part was designed to withstand the applied aero-load, and satisfy the axial traversing speed of 10 mm/s at whole operation envelops.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.6
• /
• pp.34-42
• /
• 2022

A correlation between propellant supply condition and chamber pressure in GCH₄-LOx small rocket engine was explored and hot-firing tests were conducted to analyze the engine performance characteristics according to the equivalence ratio variation at a constant chamber pressure. Correlation studies have shown that chamber pressure is linearly proportional to oxidizer supply pressure. As a result of the test, the thrust, specific impulse and characteristic velocity that are the main performance parameters of a rocket engine, were found to be enhanced as the equivalence ratio starting from a fuel-lean condition approached the stoichiometric ratio, but the efficiencies of characteristic velocity and specific impulse were on the contrary, in their dependency on the equivalence ratio.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.294-298
• /
• 2001

Satellite propulsion system is employed for orbit transfer, orbit correction, and attitude control. The monopropellant feeding system in the low-earth-orbit satellite blowdowns fuel to the thrust chamber. The thrust produced by the thruster depends on fuel amount flowed into the combustion chamber. If the thruster valve be given on-off signal from on-board commander in the satellite, valve will be opened or closed. When the thrusters fire fuel flows through opened thruster valve. Instantaneous stoppage of flow in according to valve actuation produces transient pressure due to pressure wave. This paper describes transient pressure predictions of the KOMPSAT2 propulsion system resulting from latching valve and thrust control valve operations. The time-dependent set of the fluid mass and momentum equations are calculated by Method of Characteristics (MOC).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.111-114
• /
• 2009

A catalyst ignitor of small thrust engine using hydrogen peroxide and kerosene was designed and fabricated, which confirmed mass flow rate for design pressure through the water cold-flow test in this study. In order to investigate ignition performance, it was changed that mixture ratio for kerosene mass flow rate in a position which heat of hydrogen peroxide decomposition comes to a steady state. And we confirmed stable ignition property in a wide range of mixture ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.256-259
• /
• 2007

In this paper, the combustion characteristics of hybrid rocket were studied with various port number of the cylindrical multi-port grain. For the regression rate case, as the port number increases, the both port regression rate and end-surface regression rate tend to increase. For the performance parameter case, as the port number increases, the O/F ratio tends to decreases and the specific impulse tends to increase.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.60-69
• /
• 1989

안정성과 진동억제 특성이 요구되는 터어빈이나 모터등의 고속 회전기계에서는 틸팅-패드 저어널 베어링이 많이 사용되고 있다. 이는 틸팅-패드 저어널 베어링에서는 패드가 피봇이나 로울러로 지지되어 있으므로 윤활유막에서 발생하는 압력의 합력중심이 항상 이 지지점을 지나게 되어 베어링의 안정특성이 향상되기 때문이다. 틸팅-패드 저어널 베어링은 추력 베어링과 같이 불연속적인 윤활면을 갖는다. 그러므로 베어링의 입구부 선단에서 공급되는 윤활유의 충돌로 인한 압력격변이 일어나는데 이때 패드 입구부에서 발생하는 압력을 선단압력이라 한다. 이러한 선단압력으로 인한 베어링의 성능변화에 관한 연구는 주로 추력 베어링에 대하여 이론 및 실험적으로 수행 되어져 왔으며 그 결과들은 선단압력이 베어링의 성능에 미치는 영향을 무시할 수 없음을 보여주고 있다. 그러나 아직도 선단압력의 영향이 제대로 파악되고 있지 못하며, 특히 틸팅-패드 저어널 베어링에서 선단압력의 영향을 조사한 연구는 많이 부족한 실정이다. 그러므로 본 연구에서는 유한폭 틸팅-패드 저어널 베어링을 모델화한 실험장치를 설계 제작하여 선단압력을 포함한 유막내의 압력분포 및 유막두께를 연속적으로 측정함으로써 틸팅-패드 저어널 베어링의 성능에 미치는 선단압력의 영향을 실험적으로 조사하기로 한다.