• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.61-64
• /
• 2003

A comprehensive understanding is given for the hot-firing test results, which were obtained throughout the verification program of mono-propellant hydrazine thrusters producing 0.95 lbf (4.2 Newtons) of nominal steady-state thrust at an inlet pressure of 350 psia (2.41 ㎫). The scrutiny is made in terms of thrust and temperature behavior of steady state firing mode at the given propellant injection pressures of 400, 250, 100, and 50 psi. Engineering philosophy of data measurement and reduction is shortly mentioned, too.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.151-154
• /
• 2007

The purpose of this study is to identify the basic concept of thruster design through the visualization firing test on a hydrazine thruster. We designed the visual catalyst bed on the basis of the 1lbf hydrazine thruster for a low earth orbit satellite and observed visually the internal catalyst bed reaction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.317-320
• /
• 2010

In this study, the requirements for propellants to modulate the thrust of solid rocket motor were primarily investigated, followed by searching the research trends for propellants which would be feasible for the controlled solid rocket motor. And then, the theoretical performance and combustion characteristics of solid propellants being studied in ADD were demonstrated briefly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.379-382
• /
• 2017

Flow characteristics of dual bell nozzle with pintle were investigated. Thrust and thrust coefficient were compared with the pintle-bell nozzle of the same condition, and difference according to the pintle stroke was investigated. At stroke 0 mm, the thrust of the dual bell nozzle was about 13.18% higher than the bell nozzle, and when the pintle was backward, it was similar to the bell nozzle. The change in expansion ratio with stroke was considered to be more advantageous for a dual bell nozzle that performs altitude compensation through separation and transition.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.837-838
• /
• 2015

본 논문에서는 양측식 영구자석 선형 동기 전동기(Permanent Magnet Linear Synchronous Motor: 이하 PMLSM)의 전기자 분산배치를 위해 전기자에 보조치 및 Offset에 의해 나타나는 단부 코깅력을 해석하였다. 또한 가장 낮은 단부 코깅력을 가지는 Offset 위치에 대하여 역기전력을 분석하였으며 이에 따른 추력 특성에 대한 고찰을 수행하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2001.11a
• /
• pp.26-26
• /
• 2001

소형항공기용 IO-540 왕복엔진을 대상으로 추진기관의 성능에 미치는 배압 특성을 조사하기 위해서 지상 성능시험을 수행하였다. 본 시험은 6가지 배기조건에 대해서 엔진의 배압과 흡기압력, 토크, 그리고 프로펠러의 정지추력을 측정하였다. 엔진의 배압은 대체로 머플러를 장착할 경우와 배기관 끝단이 상대적으로 직경이 작고 길이가 길수록 증가하였다. 배압 특성은 특히 엔진의 회전속도가 고속 영역으로 갈수록 프로펠러 추력에 변화를 나타냈으며 전반적으로 추진기관 성능에 미세한 영향을 미치는 것으로 나타났다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.23-28
• /
• 2011

The engine ground and altitude tests were carried out to investigate the effect of jet fuel alteration on the performance of a small turbojet engine. JP-S was supplied 8% higher than JP-8 by fuel metering system at the same command. The employment of JP-S showed the similar starting characteristic to that of JP-8, however, difference in the ignition time and acceleration rate of engine speed due to the difference of fuel flow rate by fuel metering system was observed. In spite of jet fuel alteration, the test results yield the similar steady-state engine performance in net thrust, air flow, exhaust gas temperature, etc. On the other hand, the fuel consumption of JP-S increased by 5 % compared with that of JP-8. In point of specific fuel consumption (SFC), SFC of JP-S was approximately 1.1~2.6 %, 5 % higher than that of JP-8 in ground and altitude tests respectively at the same thrust.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.410-415
• /
• 2010

The engine ground and altitude tests were carried out to investigate the effect of jet fuel alteration on the performance of a small turbojet engine. JP-S was supplied 8% higher than JP-8 by fuel metering system at the same command. The employment of JP-S showed the similar starting characteristic to that of JP-8, however, difference in the ignition time and acceleration rate of engine speed due to the difference of fuel flow rate by fuel metering system was observed. In spite of jet fuel alteration, the test results yield the similar Steady-State engine performance in Net thrust, Air flow, Exhaust Gas Temperature, etc. On the other hand, the Fuel consumption of JP-S increased by 5 % compared with that of JP-8. In point of Specific Fuel Consumption (SFC), SFC of JP-S was approximately 1.1~2.6 %, 5 % higher than that of JP-8 in ground and altitude tests respectively at the same thrust.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.139-143
• /
• 2005

Combustion Test Facility for Liquid Rocket Engine using kerosene and liquid oxygen has been developed for the purpose of cooling and performance study. Test engine of thrust 0.5 KN(design thrust) is tested to confirm the normal operation. Therefore, water-cooled firing tests using kerosene engine with injectors of fuel-centered coaxial type are conducted. With the viewpoint of characteristic velocity, and specific impulse at sea level, and chamber pressure on OF mixture ratio are analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.213-217
• /
• 2011

Unsteady numerical simulations of pintle nozzles were implemented for solid rocket thrust vector control. The variation of pintle location was considered using unsteady numerical techniques, and dynamic characteristics of various pintle models were investigated. In order to consider the variation of the pintle location, a moving mesh method was applied. The effects of shape and location of the pintle nozzle have been analytically investigated. And the results were compared with numerical results. The chamber pressure, mass flow and thrust are analyzed to take account dynamic characteristics of pintle performance.