• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.1-8
• /
• 2019

An experimental study is performed to observe the characteristics of the thrust vectoring control (TVC) of the supersonic jet using proportional control valves. It is observed that three different TVC characteristics exist as the nozzle pressure ratio varies. Strong hysteresis phenomena are also observed during the valve control for a certain range of the nozzle pressure ratio. It is also noticed that the secondary chamber pressure is one of the influencing parameters for the TVC. Therefore, a control algorithm utilizing the secondary chamber pressure coefficient as a predictor is applied to achieve the stable TVC avoiding the hysteresis. Consequently, the stable TVC with the maximum deflection angle of about 20-degree has been realized using the proportional control valves.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.1026-1030
• /
• 2010

This paper summarizes the activities performed for the development of a BLDC(Brushless Direct Current) motor driven cryogenic thrust control valve with application to KSLV-II rocket engine. The developed thrust control valve can modulate the flow rate of liquid oxygen under cryogenic temperature of 90K and high pressure of 113.2 bar with the help of electro-mechanical actuator driven by a BLDC motor. This valve can be applied to an engine combustion test after minor change because all development certification test have been performed successfully.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.443-446
• /
• 2012

A thrust control valve of a liquid rocket engine plays a role to increase or decrease the thrust of an LRE by modulating the flow rate of propellant into a gas-generator. This paper deals with a flow regulator that has functions of not only modulating thrust but also maintaining constant flow rate regardless of pressure change at inlet or outlet of the flow regulator. A direct acting flow regulator was fabricated and tested for the comparison of experimental and simulation results under steady-state conditions. The drawbacks and limitations of the flow regulator were analyzed. Also the new design of a flow regulator was proposed.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.51-56
• /
• 2002

Satellite propulsion system is employed for orbit transfer, orbit correction, and attitude control. The monopropellant feeding system in the low-earth-orbit satellite blowdowns fuel to the thrust chamber. The thrust produced by the thruster depends on fuel amount flowed into the combustion chamber. If the thruster valve be given on-off signal from on-board commander in the satellite, valve will be opened or closed. When the thrusters fire fuel flows through opened thruster valve, instantaneous stoppage of flow in according to valve actuation produces transient pressure due to pressure wave. This paper describes transient pressure predictions of the KOMPSAT-2 propulsion system resulting from latching valve and thrust control valve operations. The time-dependent set of the fluid mass and momentum equations are calculated by MOC.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.12
• /
• pp.1055-1062
• /
• 2012

In this paper, the mathematical models and control algorithm of a thrust control valve were described as a precedent study on the design of thrust control algorithm for a liquid rocket engine (LRE). Numerical simulations were performed using a simplified simulation system of an LRE and the developed mathematical models were validated by comparison with the experimental results. Through these research, basic data were acquired for the development of a thrust control algorithm for a LRE.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.225-229
• /
• 2012

대기가 희박한 고고도 환령이나 급격한 선회를 위해 2차분사에 의한 추력벡터제어를 사용한다. 8개의 2차분사구를 갖는 고체로켓모터를 대상으로, 2차분사의 유량을 조절하는 밸브의 개도가 추력, 측추력 및 롤 모멘트에 미치는 영향을 해석적으로 연구하였다. 정상 상태의 3차원 Reynolds Averaged Navier-Stokes 식의 해를 구하였으며, 난류를 위해 Spalart-Almaras 모델을 사용하였다. 수치해석의 타당성을 평가하기 위해 실험 결과와 해석결과를 비교하였다. 밸브의 개도가 증가함에 따라 추력은 감소하나 측추력은 증가한다. 반면, 롤 모멘트의 경우, 밸브와 2차분사 파이프의 상호작용에 의해 개도에 비례하지 않는다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.363-367
• /
• 2005

Latching valves are operated like solenoid valves by open/close command and they maintain final open or close commend without electric power source, so they are widely used in propulsion system of satellite and launch vehicle requiring reliability and being subject of restriction of power. This paper present design and test procedure of latching valve using permanent magnet polarized solenoid, which is developed for 45N Hydrazine propulsion system, to estimate feasibility of design and manufacture of latching valve.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.74-84
• /
• 2005

This paper include the investigation of finding the system characteristics of facility by simulating open-type turbo-pump fed system, which has commercial control valves, using AMESIM (Advanced Modeling Environment Simulation) commercial software. After developing a flight-type control valve on the basis of the results, the system characteristics of facility for control and valve tests is estimated. Especially, one of purposes of this paper is to find PID value of each commercial control valve in the facility for system test. To find suitable control logic, PI and PID modes are also compared. This paper also introduces design parameters of valve and equipment for thrust control and TDS simulation, which are using control valves.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.96-103
• /
• 2005

The main purpose of launch vehicle is to insert satellite into a target orbit safely and correctly. To accomplish the main purpose of launch vehicle, the inserting velocity, inserting angle, and final mass of launch vehicle should be within the allowable range. In general, such requirements are satisfied with applying TCS(Thrust Control System) and TDS(Tank Depletion System), which manage thrust and mixture ratio by controlling propellant flow rate with thrust and mixture ratio control valves. In this study, the control characteristics of thrust and mixture ratio control valve were examined by PID control logic for stable operation of liquid-Propellant rocket engine at on-dosing point. The analysis on the control characteristics of control valves was done with AMESim code and the results from control valve test facility at KARI.

• Bulletin of the Korean Space Science Society
• /
• 2004.04a
• /
• pp.97-97
• /
• 2004

현재 KSLV-I에서 탑재부의 Pitch, Yaw, Roll의 3축 제어 및 2단부의 Roll 제어를 위해 사용되는 보조 추진 시스템은 구성이 단순하며, 신뢰성이 높은 것으로 알려져 있는 단일 추진제인 하이드라진을 이용하는 추진 시스템을 고려하고 있다. 이러한 하이드라진 추진 시스템은 추력실 전방에 설치되어 있는 추력기 밸브의 ON/OFF를 이용하여 추력을 조절하게 되는데, 이 때 추력기 밸브의 빠른 작동으로 인해 수격현상에 의한 급격한 압력 상승이 발생하게 되어 구조물의 손상을 발생하게 된다. (중략)